Gorka Elordi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gorka Elordi has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Gartzen Lopez
Department of Chemical Engineering, University of the Basque Country UPV/EHU, Bilbao, Spain
2 shared publications - Javier Bilbao
Department of Chemical Engineering
2 shared publications - Martin Olazar
Department of Chemical Engineering, University of the Basque Country, UPV/EHU, Bilbao, Spain
2 shared publications - Roberto Aguado
Department of Chemical Engineering, University of the Basque Country UPV/EHU, P.O. Box 644, E48080 Bilbao, Spain
2 shared publications Miriam Arabiourrutia
University of the Basque Country
1 shared publication
Latest Publications
- 22 October 2007
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 5 (1)
Characterization of the Liquid Obtained in Tyre Pyrolysis in a Conical Spouted Bed Reactor
Used tyres pose a serious environmental problem and pyrolysis is considered one of the more feasible solutions that may be economically profitable on a large scale. In this study the pyrolysis of tyres has been carried out in a conical spouted bed reactor at 500 °C and the liquid product has been characterized taking into account composition, heat value and simulated distillation. The tyre mass feed in each run was 2 g and the bed was made up of 15 g of sand. Pyrolysis of scrap tyre at the 500 °C gives way to a yield of 3.1% of gases, 37.6% of liquid fraction (C5-C10 range hydrocarbons), 25.6% of tar (C11+) and 33.7% of char. The liquid fraction is of suitable quality for its use as fuel but the char requires activation for its upgrading.
- 22 October 2007
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 5 (1)
Characterization of the Liquid Obtained in Tyre Pyrolysis in a Conical Spouted Bed Reactor
Used tyres pose a serious environmental problem and pyrolysis is considered one of the more feasible solutions that may be economically profitable on a large scale. In this study the pyrolysis of tyres has been carried out in a conical spouted bed reactor at 500 °C and the liquid product has been characterized taking into account composition, heat value and simulated distillation. The tyre mass feed in each run was 2 g and the bed was made up of 15 g of sand. Pyrolysis of scrap tyre at the 500 °C gives way to a yield of 3.1% of gases, 37.6% of liquid fraction (C5-C10 range hydrocarbons), 25.6% of tar (C11+) and 33.7% of char. The liquid fraction is of suitable quality for its use as fuel but the char requires activation for its upgrading.
- 4 October 2007
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 5 (1)
Catalytic Pyrolysis of High Density Polyethylene on a HZSM-5 Zeolite Catalyst in a Conical Spouted Bed Reactor
HDPE has been pyrolysed at 450 °C and 500 °C using HZSM-5 zeolite as a catalyst. Batch runs have been carried out at atmospheric pressure in a conical spouted bed reactor. Product analysis has been carried out by means of a GC, connected on-line with a thermostated line. The degradation rate of the plastic is slightly faster at 500 °C than at 450 °C and much faster than thermal pyrolysis in both cases. Products have been grouped into five lumps: the lump of light olefins, C2-C4; light alkanes, C1-C4; the gasoline fraction, C5-C11 compounds; C11+ hydrocarbons; and the coke deposited on the catalyst. An HZSM-5 catalyst is appropriate to obtain light olefins; about 55 wt% in both cases. The yield of gasoline fraction is also considerable and although its composition is not suitable for commercial gasoline, is interesting for its use in petrochemistry. The catalyst deactivation rate is low.
- 4 October 2007
- Published by Walter de Gruyter GmbH in International Journal of Chemical Reactor Engineering
- Vol. 5 (1)
Catalytic Pyrolysis of High Density Polyethylene on a HZSM-5 Zeolite Catalyst in a Conical Spouted Bed Reactor
HDPE has been pyrolysed at 450 °C and 500 °C using HZSM-5 zeolite as a catalyst. Batch runs have been carried out at atmospheric pressure in a conical spouted bed reactor. Product analysis has been carried out by means of a GC, connected on-line with a thermostated line. The degradation rate of the plastic is slightly faster at 500 °C than at 450 °C and much faster than thermal pyrolysis in both cases. Products have been grouped into five lumps: the lump of light olefins, C2-C4; light alkanes, C1-C4; the gasoline fraction, C5-C11 compounds; C11+ hydrocarbons; and the coke deposited on the catalyst. An HZSM-5 catalyst is appropriate to obtain light olefins; about 55 wt% in both cases. The yield of gasoline fraction is also considerable and although its composition is not suitable for commercial gasoline, is interesting for its use in petrochemistry. The catalyst deactivation rate is low.