T. C. Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
T. C. Yang has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Kwang Yoo
Naval Research Laboratory , 4555 Overlook Ave., Washington, D.C. 20375
11 shared publicationsWen-Bin Yang
National Institute of Standards and Technology , Stop 8920, 100 Bureau Drive, Gaithersburg, Maryland 20899
3 shared publicationsLaurie Fialkowski
Naval Res. Lab., Washington, DC 20375
2 shared publicationsAlenka Zajić
Naval Res. Lab., Washington, DC 20375
1 shared publicationAzmi Al-Kurd
Patton Electronics, Inc., Gaithersburg, MD 20879
1 shared publicationD. Dacol
Naval Res. Lab., Washington, DC 20375
1 shared publication
Latest Publications
- 1 October 2011
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 130 (4) , 1995-2002
Relating the performance of time-reversal-based underwater acoustic communications in different shallow water environments
The performance of underwater acoustic communications, such as the output signal-to-noise ratio (OSNR), is generally dependent on the channel specifics, hence a channel model is normally required as the performance of the channel equalizer depends on the number of tap coefficients used (e. g., a sparse equalizer) which are different for different oceans having different multipath arrivals. This letter presents theoretical arguments, and experimental data from different oceans that suggest that the increase of OSNR with the number of diverse receivers (in terms of the effective number of receivers) and the decrease of OSNR with the channel-estimation error follow a universal relationship using the time-reversal or correlation-based equalizer, despite the fact that the channels have very different properties. The reason is due to the fact that the OSNR is a function of the q function, the auto-correlation of the received impulse responses summed over all receiver channels, and the q function is approximately the same for all shallow waters given a sufficient (>= 4 - 6) number of receivers. (C) 2011 Acoustical Society of America. [DOI: 10.1121/1.3632078]
- 1 October 2011
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 130 (4) , 1995-2002
Relating the performance of time-reversal-based underwater acoustic communications in different shallow water environments
The performance of underwater acoustic communications, such as the output signal-to-noise ratio (OSNR), is generally dependent on the channel specifics, hence a channel model is normally required as the performance of the channel equalizer depends on the number of tap coefficients used (e. g., a sparse equalizer) which are different for different oceans having different multipath arrivals. This letter presents theoretical arguments, and experimental data from different oceans that suggest that the increase of OSNR with the number of diverse receivers (in terms of the effective number of receivers) and the decrease of OSNR with the channel-estimation error follow a universal relationship using the time-reversal or correlation-based equalizer, despite the fact that the channels have very different properties. The reason is due to the fact that the OSNR is a function of the q function, the auto-correlation of the received impulse responses summed over all receiver channels, and the q function is approximately the same for all shallow waters given a sufficient (>= 4 - 6) number of receivers. (C) 2011 Acoustical Society of America. [DOI: 10.1121/1.3632078]
- 1 March 2010
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 127 (3_Suppleme) , 1820
Using the vector sensors as receivers for underwater acoustic communications.
A vector sensor package (VSP) generally consists of three orthogonally oriented sensors and an omni directional hydrophone, all packed in a small compact housing. Because of its small size, the VSP might be more useful than a hydrophone array. In contrast to the hydrophone array, which has a non‐negligible vertical aperture and is difficult to deploy on an autonomous underwater vehicle(AUV), the VSP can be easily deployed on the AUV and used for underwater acoustic communications (UAC). However, the usefulness of the VSP depends on whether it provides the same spatial diversity as a hydrophone array. Hence, to address this question, this paper investigates the spatial correlation characteristics of the VSP and the bit error rates and/or output SNRs, based on at sea data, between the VSPs and the hydrophone array. The data were collected in May of 2009 on the New Jersey shelf. A hydrophone array and a VSP were deployed close to the ocean bottom and used for UACs. The source was towed at a slow speed, transmitting signals of various modulations at distances 0.5 to a few kilometers from the receivers. Initial results will be presented. [Work supported by the Office of Naval Research.]
- 1 March 2010
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 127 (3_Suppleme) , 1820
Using the vector sensors as receivers for underwater acoustic communications.
A vector sensor package (VSP) generally consists of three orthogonally oriented sensors and an omni directional hydrophone, all packed in a small compact housing. Because of its small size, the VSP might be more useful than a hydrophone array. In contrast to the hydrophone array, which has a non‐negligible vertical aperture and is difficult to deploy on an autonomous underwater vehicle(AUV), the VSP can be easily deployed on the AUV and used for underwater acoustic communications (UAC). However, the usefulness of the VSP depends on whether it provides the same spatial diversity as a hydrophone array. Hence, to address this question, this paper investigates the spatial correlation characteristics of the VSP and the bit error rates and/or output SNRs, based on at sea data, between the VSPs and the hydrophone array. The data were collected in May of 2009 on the New Jersey shelf. A hydrophone array and a VSP were deployed close to the ocean bottom and used for UACs. The source was towed at a slow speed, transmitting signals of various modulations at distances 0.5 to a few kilometers from the receivers. Initial results will be presented. [Work supported by the Office of Naval Research.]
- 1 July 2009
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 126 (1) , 220-228
Interference suppression for code-division multiple-access communications in an underwater acoustic channel
In a code-division multiple-access communications network, the signal from a nearby user often creates a strong interference for the signal from a distant user. This is known as the near-far problem. Power control of source levels is ineffective in an underwater acoustic channel due to the slow sound speed. Interference rejection based on code orthogonality is ineffective using matched-filter processing due to the fact that multipath arrivals effectively destroy the code orthogonality and that the signal arrival times between different users are not synchronized. An algorithm, called hyperspace cancellation by coordinate zeroing, is used in this paper to remove/suppress interference. Using a fast Walsh–Hadamard transform (FWHT) based on the interferer’s code sequence, the interference signal is enhanced and removed by coordinate zeroing. The residual signal is transformed back using an inverse FWHT. The filtered data, with the interference signal largely removed, are processed using the desired signal code sequence. Two methods previously developed for direct-sequence spread-spectrum communications in an underwater channel are used to extract the transmitted symbols. Low bit error rate (<10−2) is found with the at-sea data for signal-to-interference ratio as low as −8 to −11 dB.
- 1 July 2009
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 126 (1) , 220-228
Interference suppression for code-division multiple-access communications in an underwater acoustic channel
In a code-division multiple-access communications network, the signal from a nearby user often creates a strong interference for the signal from a distant user. This is known as the near-far problem. Power control of source levels is ineffective in an underwater acoustic channel due to the slow sound speed. Interference rejection based on code orthogonality is ineffective using matched-filter processing due to the fact that multipath arrivals effectively destroy the code orthogonality and that the signal arrival times between different users are not synchronized. An algorithm, called hyperspace cancellation by coordinate zeroing, is used in this paper to remove/suppress interference. Using a fast Walsh–Hadamard transform (FWHT) based on the interferer’s code sequence, the interference signal is enhanced and removed by coordinate zeroing. The residual signal is transformed back using an inverse FWHT. The filtered data, with the interference signal largely removed, are processed using the desired signal code sequence. Two methods previously developed for direct-sequence spread-spectrum communications in an underwater channel are used to extract the transmitted symbols. Low bit error rate (<10−2) is found with the at-sea data for signal-to-interference ratio as low as −8 to −11 dB.
- 1 December 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 124 (6) , 3632-3647
Low probability of detection underwater acoustic communications using direct-sequence spread spectrum
Direct-sequence spread spectrum is used for underwater acoustic communications between nodes, at least one of which is moving. At-sea data show that the phase change due to source motion is significant: The differential phase between two adjacent symbols is often larger than the phase difference between symbols. This poses a challenge to phase-detection based receiver algorithms when the source or receiver is moving. A pair of energy detectors that are insensitive to the phase fluctuations is proposed, whose outputs are used to determine the relationship between adjacent symbols. Good performance is achieved for a signal-to-noise ratio (SNR) as low as −10dB based on at-sea data. While the method can be applied to signaling using short code sequences, the focus in this paper is on long code sequences for the purpose of achieving a high processing gain (at the expense of a low data rate), so that communications can be carried out at a low input SNR to minimize the probability of detection (PD) by an interceptor. PD is calculated for a typical shallow water environment as a function of range for several source levels assuming a broadband energy detector with a known signal bandwidth.
- 1 December 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 124 (6) , 3632-3647
Low probability of detection underwater acoustic communications using direct-sequence spread spectrum
Direct-sequence spread spectrum is used for underwater acoustic communications between nodes, at least one of which is moving. At-sea data show that the phase change due to source motion is significant: The differential phase between two adjacent symbols is often larger than the phase difference between symbols. This poses a challenge to phase-detection based receiver algorithms when the source or receiver is moving. A pair of energy detectors that are insensitive to the phase fluctuations is proposed, whose outputs are used to determine the relationship between adjacent symbols. Good performance is achieved for a signal-to-noise ratio (SNR) as low as −10dB based on at-sea data. While the method can be applied to signaling using short code sequences, the focus in this paper is on long code sequences for the purpose of achieving a high processing gain (at the expense of a low data rate), so that communications can be carried out at a low input SNR to minimize the probability of detection (PD) by an interceptor. PD is calculated for a typical shallow water environment as a function of range for several source levels assuming a broadband energy detector with a known signal bandwidth.
- 1 July 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 124 (1) , 113-127
Temporal coherence of sound transmissions in deep water revisited
This paper examines the signal coherence loss due to internal waves in deep water in terms of the signal coherence time and compare to data reported in the literature over the past 35 years. The coherence time of the early raylike arrivals was previously modeled by Munk and Zachariasen ["Sound propagation through a fluctuating stratified ocean: Theory and observation," J. Acoust. Soc. Am. 59, 818-838 (1976)] using the supereikonal approximation and by Dashen et al. ["Path-integral treatment of acoustic mutual coherence functions for arrays in a sound channel," J. Acoust. Soc. Am. 77, 1716-1722 (1985)] using the path integral approach; a -1 [corrected] power frequency dependence and a -1/2 [corrected] power range dependence were predicted. Recent data in shallow water in downward refractive environments with internal waves suggested that the signal coherence time of the mode arrivals follows a -3/2 power frequency dependence and a -1/2 power range dependence. Since the temporal coherence of the acoustic signal is related to the temporal coherence of the internal waves, based on the observation that the (linear) internal waves in deep and shallow waters have a similar frequency spectrum, it is argued that the modelike arrivals in deep water should exhibit a similar frequency dependence in deep and shallow waters. This argument is supported by a brute-force application of the path integral to mode arrivals based on the WKB relation between the ray and mode. It is found that the data are consistent with the -3/2 power frequency dependence but more data are needed to further test the hypothesis.
- 1 July 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 124 (1) , 113-127
Temporal coherence of sound transmissions in deep water revisited
This paper examines the signal coherence loss due to internal waves in deep water in terms of the signal coherence time and compare to data reported in the literature over the past 35 years. The coherence time of the early raylike arrivals was previously modeled by Munk and Zachariasen ["Sound propagation through a fluctuating stratified ocean: Theory and observation," J. Acoust. Soc. Am. 59, 818-838 (1976)] using the supereikonal approximation and by Dashen et al. ["Path-integral treatment of acoustic mutual coherence functions for arrays in a sound channel," J. Acoust. Soc. Am. 77, 1716-1722 (1985)] using the path integral approach; a -1 [corrected] power frequency dependence and a -1/2 [corrected] power range dependence were predicted. Recent data in shallow water in downward refractive environments with internal waves suggested that the signal coherence time of the mode arrivals follows a -3/2 power frequency dependence and a -1/2 power range dependence. Since the temporal coherence of the acoustic signal is related to the temporal coherence of the internal waves, based on the observation that the (linear) internal waves in deep and shallow waters have a similar frequency spectrum, it is argued that the modelike arrivals in deep water should exhibit a similar frequency dependence in deep and shallow waters. This argument is supported by a brute-force application of the path integral to mode arrivals based on the WKB relation between the ray and mode. It is found that the data are consistent with the -3/2 power frequency dependence but more data are needed to further test the hypothesis.
- 1 February 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 123 (2) , 842-855
Performance analysis of direct-sequence spread-spectrum underwater acoustic communications with low signal-to-noise-ratio input signals
Direct-sequence spread-spectrum signals collected from the TREX04 experiment are analyzed to determine the bit-error-rate (BER) as a function of the input signal-to-noise ratio (SNR) for a single receiver. A total of 1160 packets of data are generated by adding ambient noise data collected at sea to the signal data (in postprocessing) to create signals with different input-SNR, some as low as −15dB. Two methods are analyzed in detail, both using a time-updated channel impulse-response estimate as a (matched) filter to mitigate the multipath-induced interferences. The first method requires an independent estimate of the time-varying channel impulse-response function; the second method uses the channel impulse-response estimated from the previous symbol as the matched filter. The first method yields an average BER <10−2 for input-SNR as low as −12dB and the second method yields a similar performance for input-SNR as low as −8dB. The measured BERs are modeled using the measured signal amplitude fluctuation statistics and processing gain obtained by de-spreading the received signal with the transmitted code sequence. Performance losses caused by imprecise symbol synchronization at low input-SNR, uncertainty in channel estimation, and signal fading are quantitatively modeled and compared with data.
- 1 February 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 123 (2) , 842-855
Performance analysis of direct-sequence spread-spectrum underwater acoustic communications with low signal-to-noise-ratio input signals
Direct-sequence spread-spectrum signals collected from the TREX04 experiment are analyzed to determine the bit-error-rate (BER) as a function of the input signal-to-noise ratio (SNR) for a single receiver. A total of 1160 packets of data are generated by adding ambient noise data collected at sea to the signal data (in postprocessing) to create signals with different input-SNR, some as low as −15dB. Two methods are analyzed in detail, both using a time-updated channel impulse-response estimate as a (matched) filter to mitigate the multipath-induced interferences. The first method requires an independent estimate of the time-varying channel impulse-response function; the second method uses the channel impulse-response estimated from the previous symbol as the matched filter. The first method yields an average BER <10−2 for input-SNR as low as −12dB and the second method yields a similar performance for input-SNR as low as −8dB. The measured BERs are modeled using the measured signal amplitude fluctuation statistics and processing gain obtained by de-spreading the received signal with the transmitted code sequence. Performance losses caused by imprecise symbol synchronization at low input-SNR, uncertainty in channel estimation, and signal fading are quantitatively modeled and compared with data.
- 1 December 2007
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 122 (6) , 3338-3352
Subbottom profiling using a ship towed line array and geoacoustic inversion
Bottom profiling traditionally uses broadband signals received on a line array at long ranges to estimate the bottom layer structure and thickness. In this paper, a subbottom profiling method is developed and applied to a ship-towed line array using the same ship towed source to estimate the subbottom layer structure and thickness. A ship towed line-array system can be used to estimate bottom properties using geoacoustic inversion and can cover a wide area in a short time. It needs some prior information about the subbottom structure and layer thickness, without which the solution can be ambiguous and even erratic when resolving parameters over a wide area. It is shown that the required subbottom information can be obtained from the time–angle relation by beamforming the same acoustic signal data used for geoacoustic inversion. The time-angle analysis is used to expose the prevalent physics intrinsic to geoacoustic inversion. One finds that the tau–p relation of the bottom and the bottom reflection coefficients, sampled at discrete angles associated with bottom and multiple surface-bottom returns, are often adequate, for many practical applications, to uniquely determine the geoacoustic bottom at low (⩽1kHz) frequencies.
- 1 December 2007
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 122 (6) , 3338-3352
Subbottom profiling using a ship towed line array and geoacoustic inversion
Bottom profiling traditionally uses broadband signals received on a line array at long ranges to estimate the bottom layer structure and thickness. In this paper, a subbottom profiling method is developed and applied to a ship-towed line array using the same ship towed source to estimate the subbottom layer structure and thickness. A ship towed line-array system can be used to estimate bottom properties using geoacoustic inversion and can cover a wide area in a short time. It needs some prior information about the subbottom structure and layer thickness, without which the solution can be ambiguous and even erratic when resolving parameters over a wide area. It is shown that the required subbottom information can be obtained from the time–angle relation by beamforming the same acoustic signal data used for geoacoustic inversion. The time-angle analysis is used to expose the prevalent physics intrinsic to geoacoustic inversion. One finds that the tau–p relation of the bottom and the bottom reflection coefficients, sampled at discrete angles associated with bottom and multiple surface-bottom returns, are often adequate, for many practical applications, to uniquely determine the geoacoustic bottom at low (⩽1kHz) frequencies.
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01977385,p. 1-5
Modeling and Interpretation of Beamforming Gain and Diversity Gain for Underwater Acoustic Communications
Output signal-to-noise ratios for a multichannel decision feedback equalizer were measured from experimental BPSK data as a function of the receiver spacing, number of receivers used, and array aperture and reported in a paper in OCEANS 2005 by the author. This paper discusses the theory and reports numerical modeling results to compare with the data
- 1 September 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 01977385,p. 1-5
Modeling and Interpretation of Beamforming Gain and Diversity Gain for Underwater Acoustic Communications
Output signal-to-noise ratios for a multichannel decision feedback equalizer were measured from experimental BPSK data as a function of the receiver spacing, number of receivers used, and array aperture and reported in a paper in OCEANS 2005 by the author. This paper discusses the theory and reports numerical modeling results to compare with the data
- 1 July 2006
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 120 (1) , 231-246
Consistency and reliability of geoacoustic inversions with a horizontal line array
- 1 July 2006
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 120 (1) , 231-246
Consistency and reliability of geoacoustic inversions with a horizontal line array
- 1 September 2005
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 118 (3_Suppleme) , 1857
Geoacoustic inversion using ship noise received on the ship-towed line array
- 1 September 2005
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 118 (3_Suppleme) , 1857
Geoacoustic inversion using ship noise received on the ship-towed line array