Yu.G. Rezvov
Research Subjects
Yu.G. Rezvov has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
V. V. Proklov
21 shared publications- Sergey N. Antonov
Fryazino Branch, Kotelnikov Institute of Radio Engineering and Electronics, Russian Academy of Sciences, Fryazino, Russia
18 shared publications A. V. Vainer
Russian Academy of Sciences
16 shared publicationsS. N. Antonov
Kotelnikov Institute of Radio Engineering and Electronics, Russian Academy of Sciences, Fryazino Branch, Fryazino, Russia
9 shared publicationsAlexander Vainer
Institute of Radio-engineering and Electronics, Russian Academy of Sciences, Moscow, Russia
4 shared publicationsL. N. Chesnokov
4 shared publications
Latest Publications
- 1 February 2024
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 50 (2) , 90-94
Acousto-Optic MultiBeam Axial Diffraction in Paratellurite
—To form a multibeam radiation pattern, it is proposed to use the axial geometry of acousto-optic interaction in paratellurite. In the single frequency mode, the use of this geometry for angular scanning is characterized by a dip in the frequency response. Optimization of a multifrequency radio signal makes it possible to efficiently divide laser radiation into several beams with maintaining the fundamental advantages of axial geometry: minimum crystal size and power consumption.
- 1 February 2024
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 50 (2) , 90-94
Acousto-Optic MultiBeam Axial Diffraction in Paratellurite
—To form a multibeam radiation pattern, it is proposed to use the axial geometry of acousto-optic interaction in paratellurite. In the single frequency mode, the use of this geometry for angular scanning is characterized by a dip in the frequency response. Optimization of a multifrequency radio signal makes it possible to efficiently divide laser radiation into several beams with maintaining the fundamental advantages of axial geometry: minimum crystal size and power consumption.
- 24 October 2022
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 68 (5) , 435-441
Internal Thermal Effects in Axial Paratellurite-Based Acoustooptic Deflector
The thermal angular deviation of the zero and working orders in an axial paratellurite-based acoustooptic deflector is experimentally investigated at a control power up to 6.5 W in the continuous mode. Regional measurements (near the transducer, in the middle, and at the sound absorber) are performed for variants of +1 and –1 working order diffraction and show a linear dependence of the angular deviation on the control power. A qualitative description of deviation of the working order as a combined action of two factors is proposed: (1) zeroth-order deviation at passage of two thermal optically denser prisms attached to the transducer and sound absorber and (2) reduction in the diffraction angle due to the growth in the sound speed at crystal heating. The inhomogeneity of the temperature field cannot be used to uniquely separate the contributions of these factors to the averaged working-order deviation. It is shown that the technology of the liquid contact between the endface surface of a piezoelectric transducer and the body increases the stability of the deflector parameters as light passes in the zone adjacent to the transducer. It is revealed that for +1 order diffraction there is a zone with a minimum thermal deviation between the piezoelectric transducer and the absorber. This is explained by the mutual compensation between the zeroth-order deviation (in the field of the thermal optical wedge from the absorber) and the factor of increased in sound speed.
- 24 October 2022
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 68 (5) , 435-441
Internal Thermal Effects in Axial Paratellurite-Based Acoustooptic Deflector
The thermal angular deviation of the zero and working orders in an axial paratellurite-based acoustooptic deflector is experimentally investigated at a control power up to 6.5 W in the continuous mode. Regional measurements (near the transducer, in the middle, and at the sound absorber) are performed for variants of +1 and –1 working order diffraction and show a linear dependence of the angular deviation on the control power. A qualitative description of deviation of the working order as a combined action of two factors is proposed: (1) zeroth-order deviation at passage of two thermal optically denser prisms attached to the transducer and sound absorber and (2) reduction in the diffraction angle due to the growth in the sound speed at crystal heating. The inhomogeneity of the temperature field cannot be used to uniquely separate the contributions of these factors to the averaged working-order deviation. It is shown that the technology of the liquid contact between the endface surface of a piezoelectric transducer and the body increases the stability of the deflector parameters as light passes in the zone adjacent to the transducer. It is revealed that for +1 order diffraction there is a zone with a minimum thermal deviation between the piezoelectric transducer and the absorber. This is explained by the mutual compensation between the zeroth-order deviation (in the field of the thermal optical wedge from the absorber) and the factor of increased in sound speed.
- 23 June 2022
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 68 (3) , 235-241
Acousto-Optic Diffraction in an Ultrasonic Field of a Width-Profiled Transducer
Acousto-optical diffraction in an ultrasonic field of a slow acoustic mode in paratellurite excited by a hexagonal-shaped piezoelectric transducer has been simulated in a nonaxial geometry of an acousto-optic deflector. It has been established that, compared to a rectangular transducer, a width-profiled transducer reduces the characteristic scale of an acoustic inhomogeneity. As a result, the parameters of the acousto-optic interaction approach that of a homogeneous acoustic field: the maximum diffraction efficiency increases (especially in an over modulation mode with a Raman–Nath parameter of 3π), and the distortions of the transverse profile of diffracted radiation are reduced.
- 23 June 2022
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 68 (3) , 235-241
Acousto-Optic Diffraction in an Ultrasonic Field of a Width-Profiled Transducer
Acousto-optical diffraction in an ultrasonic field of a slow acoustic mode in paratellurite excited by a hexagonal-shaped piezoelectric transducer has been simulated in a nonaxial geometry of an acousto-optic deflector. It has been established that, compared to a rectangular transducer, a width-profiled transducer reduces the characteristic scale of an acoustic inhomogeneity. As a result, the parameters of the acousto-optic interaction approach that of a homogeneous acoustic field: the maximum diffraction efficiency increases (especially in an over modulation mode with a Raman–Nath parameter of 3π), and the distortions of the transverse profile of diffracted radiation are reduced.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (1) , 33
Acousto-Optic MultiBeam Axial Diffraction in Paratellurite
To form a multibeam radiation pattern, it is proposed to use the axial geometry of acousto-optic interaction in paratellurite. In the single frequency mode, the use of this geometry for angular scanning is characterized by a dip in the frequency response. Optimization of a multifrequency radio signal makes it possible to efficiently divide laser radiation into several beams with maintaining the fundamental advantages of axial geometry: minimum crystal size and power consumption. Keywords: acousto-optic diffraction, acousto-optic deflector, axial geometry, multifrequency mode, paratellurite.
- 1 January 2022
- Published by Ioffe Institute Russian Academy of Sciences in Technical Physics Letters
- Vol. 48 (1) , 33
Acousto-Optic MultiBeam Axial Diffraction in Paratellurite
To form a multibeam radiation pattern, it is proposed to use the axial geometry of acousto-optic interaction in paratellurite. In the single frequency mode, the use of this geometry for angular scanning is characterized by a dip in the frequency response. Optimization of a multifrequency radio signal makes it possible to efficiently divide laser radiation into several beams with maintaining the fundamental advantages of axial geometry: minimum crystal size and power consumption. Keywords: acousto-optic diffraction, acousto-optic deflector, axial geometry, multifrequency mode, paratellurite.
- 14 September 2021
- Published by Pleiades Publishing Ltd in Instruments and Experimental Techniques
- Vol. 64 (5) , 734-738
An Acousto-Optical Modulator for Laser Doppler Anemometers of Liquid and Gas Flows
The scheme of a laser Doppler two-beam anemometer of a liquid or gas flow based on an acousto-optic modulator on a TeO2 crystal is considered, which performs the functions of a beam splitter and a light frequency shifter. It is shown that the mode of acousto-optic diffraction, that is, axial two-phonon interaction at a slow acoustic mode, is the most optimal for anemometer circuits. In this mode, two equally intense diffracted beams with unidirectional polarizations are formed, the frequency difference between which is equal to the doubled ultrasound frequency. The calculation of the frequency of the modulator parameters for anemometers with different light wavelengths has been performed.
- 14 September 2021
- Published by Pleiades Publishing Ltd in Instruments and Experimental Techniques
- Vol. 64 (5) , 734-738
An Acousto-Optical Modulator for Laser Doppler Anemometers of Liquid and Gas Flows
The scheme of a laser Doppler two-beam anemometer of a liquid or gas flow based on an acousto-optic modulator on a TeO2 crystal is considered, which performs the functions of a beam splitter and a light frequency shifter. It is shown that the mode of acousto-optic diffraction, that is, axial two-phonon interaction at a slow acoustic mode, is the most optimal for anemometer circuits. In this mode, two equally intense diffracted beams with unidirectional polarizations are formed, the frequency difference between which is equal to the doubled ultrasound frequency. The calculation of the frequency of the modulator parameters for anemometers with different light wavelengths has been performed.
- 14 September 2021
- Published by Pleiades Publishing Ltd in Instruments and Experimental Techniques
- Vol. 64 (5) , 729-733
An Acousto-Optical Deflector Based on Paratellurite: Increasing the Thermal Stability of Parameters
The phenomena that occur during internal heating (release of the control radio power) of an acousto-optic deflector based on paratellurite with heat removal from the piezoelectric transducer through a liquid contact were experimentally investigated. It was found that, in addition to the temperature drift of the velocity of sound and the refractive indices, the temperature inhomogeneity has a significant effect on the deflector characteristics. In this case, the volume of the crystal behaves like an optical wedge, which is optically denser near the transducer and less dense at a distance from it. The effect of internal compensation of the thermal deviation of the diffracted-beam position at a certain deflector orientation is detected.
- 14 September 2021
- Published by Pleiades Publishing Ltd in Instruments and Experimental Techniques
- Vol. 64 (5) , 729-733
An Acousto-Optical Deflector Based on Paratellurite: Increasing the Thermal Stability of Parameters
The phenomena that occur during internal heating (release of the control radio power) of an acousto-optic deflector based on paratellurite with heat removal from the piezoelectric transducer through a liquid contact were experimentally investigated. It was found that, in addition to the temperature drift of the velocity of sound and the refractive indices, the temperature inhomogeneity has a significant effect on the deflector characteristics. In this case, the volume of the crystal behaves like an optical wedge, which is optically denser near the transducer and less dense at a distance from it. The effect of internal compensation of the thermal deviation of the diffracted-beam position at a certain deflector orientation is detected.
- 1 September 2021
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 66 (9) , 1078-1084
Acousto-Optic Control of the 2D Energy Profile of Laser Beam
Acousto-optic control of the energy profile of laser radiation is considered. High-efficiency multibeam Bragg diffraction with a combination of beams close in angular space that form an averaged single-beam pattern is employed. The 2D intensity profile is obtained as a product of two independent 1D profiles. A polarization-independent two-coordinate acousto-optic deflector is used to experimentally obtain several profiles (in particular, an almost uniform) with a total efficiency of no less than 85% and a switching time of about 10 μs. The method can be employed in systems for material processing using high-power lasers.
- 1 September 2021
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 66 (9) , 1078-1084
Acousto-Optic Control of the 2D Energy Profile of Laser Beam
Acousto-optic control of the energy profile of laser radiation is considered. High-efficiency multibeam Bragg diffraction with a combination of beams close in angular space that form an averaged single-beam pattern is employed. The 2D intensity profile is obtained as a product of two independent 1D profiles. A polarization-independent two-coordinate acousto-optic deflector is used to experimentally obtain several profiles (in particular, an almost uniform) with a total efficiency of no less than 85% and a switching time of about 10 μs. The method can be employed in systems for material processing using high-power lasers.
- 1 March 2021
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 67 (2) , 128-133
An Acousto-Optic Polarization-Insensitive Two-Coordinate Deflector
A new scheme of a polarization-independent two-coordinate acousto-optic deflector based on paratellurite crystals has been developed. One specific feature of the optical scheme is the use of only three single crystals without additional phase plates. A practical model of a deflector for a light wavelength of 1.06 μm, which provides a total efficiency of more than 80%, has been created. This device became the basic element in a switch for unpolarized fiber-optic channels with a switching algorithm of 1 to 25. The main parameters are as follows: the total loss ranges from 3.8 to 5.3 dB, the isolation between channels is from –45 to –60 dB, and the switching time is 7 μm.
- 1 March 2021
- Published by Pleiades Publishing Ltd in Acoustical Physics
- Vol. 67 (2) , 128-133
An Acousto-Optic Polarization-Insensitive Two-Coordinate Deflector
A new scheme of a polarization-independent two-coordinate acousto-optic deflector based on paratellurite crystals has been developed. One specific feature of the optical scheme is the use of only three single crystals without additional phase plates. A practical model of a deflector for a light wavelength of 1.06 μm, which provides a total efficiency of more than 80%, has been created. This device became the basic element in a switch for unpolarized fiber-optic channels with a switching algorithm of 1 to 25. The main parameters are as follows: the total loss ranges from 3.8 to 5.3 dB, the isolation between channels is from –45 to –60 dB, and the switching time is 7 μm.
- 1 January 2021
- Published by Ioffe Institute Russian Academy of Sciences in Журнал технической физики
- Vol. 91 (8) , 1269
Акустооптическое управление энергетическим 2D-профилем лазерного луча
The acousto-optic control of the energy profile of laser radiation is considered. A highly efficient multibeam Bragg diffraction mode with a combination of beams close in angular space, forming an averaged pattern in the form of a single beam, is used. In this case, the two-dimensional intensity profile is realized as a product of two independent one-dimensional profiles. On the basis of a polarization-independent two-coordinate acousto-optic deflector, several profiles (including a close to uniform one) were experimentally obtained with a total efficiency of no less than 85% and a profile change time of about ten microseconds. This method can be used in systems for processing materials with powerful lasers.
- 1 January 2021
- Published by Ioffe Institute Russian Academy of Sciences in Журнал технической физики
- Vol. 91 (8) , 1269
Акустооптическое управление энергетическим 2D-профилем лазерного луча
The acousto-optic control of the energy profile of laser radiation is considered. A highly efficient multibeam Bragg diffraction mode with a combination of beams close in angular space, forming an averaged pattern in the form of a single beam, is used. In this case, the two-dimensional intensity profile is realized as a product of two independent one-dimensional profiles. On the basis of a polarization-independent two-coordinate acousto-optic deflector, several profiles (including a close to uniform one) were experimentally obtained with a total efficiency of no less than 85% and a profile change time of about ten microseconds. This method can be used in systems for processing materials with powerful lasers.
- 2 November 2020
- Published by Pleiades Publishing Ltd in Instruments and Experimental Techniques
- Vol. 63 (6) , 835-841
Acousto-Optic Devices Based on Multibeam Diffraction
The multibeam acousto-optical Bragg diffraction of laser radiation is considered. This is splitting of an initial beam into several independently controlled beams (channels) without substantial light-power losses. Practically significant relationships that determine the conditions for implementing the multibeam diffraction and its main parameters have been obtained. It is shown that the necessary condition is the form of control radio signal that is close to a frequency (phase) modulated signal. Experimental studies were conducted on a polarization-insensitive acousto-optic deflector based on a paratellurite crystal. Practical applications of the multibeam diffraction are shown: laser image deposition, multichannel transmission (switching) of optical information, and the formation of the laser-beam profile.
- 2 November 2020
- Published by Pleiades Publishing Ltd in Instruments and Experimental Techniques
- Vol. 63 (6) , 835-841
Acousto-Optic Devices Based on Multibeam Diffraction
The multibeam acousto-optical Bragg diffraction of laser radiation is considered. This is splitting of an initial beam into several independently controlled beams (channels) without substantial light-power losses. Practically significant relationships that determine the conditions for implementing the multibeam diffraction and its main parameters have been obtained. It is shown that the necessary condition is the form of control radio signal that is close to a frequency (phase) modulated signal. Experimental studies were conducted on a polarization-insensitive acousto-optic deflector based on a paratellurite crystal. Practical applications of the multibeam diffraction are shown: laser image deposition, multichannel transmission (switching) of optical information, and the formation of the laser-beam profile.