Daniel Royer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Daniel Royer has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
C. Chenu
2 shared publications- Claire Prada
Institut Langevin, ESPCI Paris, CNRS (UMR 7587), PSL Res. Univ., 1 rue Jussieu, Paris 75005, France
2 shared publications - Dominique Clorennec
Laboratoire Ondes et Acoustique, ESPCI, Université Paris 7, CNRS, 10 rue Vauquelin, 75005 Paris, France
2 shared publications - A. Déom
ONERA, 29 av. Division Leclerc
1 shared publication - B. Chapuis
ONERA, 29 av. Division Leclerc
1 shared publication - D. Clorennec
Laboratoire Ondes et Acoustique, Université Paris 7-CNRS-ESPCI 10, rue Vauquelin, 75231 Paris Cedex 05-France
1 shared publication
Latest Publications
- 1 January 2009
- Published by Springer Nature in Springer Proceedings in Physics
- p. 355-363
Structural health monitoring of bonded composite patches using Lamb waves
- 1 January 2009
- Published by Springer Nature in Springer Proceedings in Physics
- p. 355-363
Structural health monitoring of bonded composite patches using Lamb waves
- 1 May 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 123 (5_Suppleme) , 3833
Second order dispersive effect on zero-group velocity Lamb modes
After a local and transient loading of a plate, the acoustic energy decay in the source area can be explained by three mechanisms: the energy transport phenomenon at the Lamb wave group velocity, the material damping and the second‐order dispersive effect. Generally, the first mechanism dominates the other two. However, some dispersion curves of Lamb modes present a minimum frequency for a nonzero wave number. Since at these points the group velocity vanishes, no energy transport occurs, and the slower other two phenomena can be observed. Using laser‐based ultrasonic techniques, we show that the mechanical response of various thin metallic plates to a laser pulse impact is dominated by the resonance of the zero group velocity S1‐Lamb mode. In the first microseconds, we observed a t‐1/2 decay of the local vibration amplitude, which cannot be explained by the material damping. We demonstrated that this effect is ascribed to the second‐order term in the dispersion relation. After this power law decay, the mechanical displacement undergoes an exponential decay corresponding to the wave damping. Then, we show that the local attenuation of the plate material can be measured without any mechanical contact.
- 1 May 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 123 (5_Suppleme) , 3833
Second order dispersive effect on zero-group velocity Lamb modes
After a local and transient loading of a plate, the acoustic energy decay in the source area can be explained by three mechanisms: the energy transport phenomenon at the Lamb wave group velocity, the material damping and the second‐order dispersive effect. Generally, the first mechanism dominates the other two. However, some dispersion curves of Lamb modes present a minimum frequency for a nonzero wave number. Since at these points the group velocity vanishes, no energy transport occurs, and the slower other two phenomena can be observed. Using laser‐based ultrasonic techniques, we show that the mechanical response of various thin metallic plates to a laser pulse impact is dominated by the resonance of the zero group velocity S1‐Lamb mode. In the first microseconds, we observed a t‐1/2 decay of the local vibration amplitude, which cannot be explained by the material damping. We demonstrated that this effect is ascribed to the second‐order term in the dispersion relation. After this power law decay, the mechanical displacement undergoes an exponential decay corresponding to the wave damping. Then, we show that the local attenuation of the plate material can be measured without any mechanical contact.
- 1 May 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 123 (5_Suppleme) , 3156
Zero-group velocity modes and local vibrations of an elastic plate
Elastic plates or cylinders can support guided modes with zero group velocity (ZGV) at a nonzero value of the wave number. The conditions required for the existence of ZGV Lamb modes in isotropic plates are discussed. It is shown that these modes appear in a range of Poisson's ratio over the value for which the cut‐off frequency curves of modes belonging to the same family intercept, i.e for a bulk wavevelocity ratio equal to a rational number. An interpretation of this phenomenon in terms of a strong repulsion between a pair of modes having a different parity in the vicinity of the cutoff frequencies is given. Using laser‐based ultrasonic techniques, we experimentally investigate some properties of these ZGV Lamb modes: resonance, backward wave propagation, interference between backward and forward waves. Experiments performed with materials of various Poisson's ratio demonstrate that the resonance spectrum of an unloaded elastic plate, locally excited by a laser pulse, is dominated by the ZGV Lamb modes. From these local resonance frequencies, thickness variations can be measured accurately and material properties like the Poisson's ratio, bulk acoustic wave velocities or material attenuation can be determined without any mechanical contact.
- 1 May 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 123 (5_Suppleme) , 3156
Zero-group velocity modes and local vibrations of an elastic plate
Elastic plates or cylinders can support guided modes with zero group velocity (ZGV) at a nonzero value of the wave number. The conditions required for the existence of ZGV Lamb modes in isotropic plates are discussed. It is shown that these modes appear in a range of Poisson's ratio over the value for which the cut‐off frequency curves of modes belonging to the same family intercept, i.e for a bulk wavevelocity ratio equal to a rational number. An interpretation of this phenomenon in terms of a strong repulsion between a pair of modes having a different parity in the vicinity of the cutoff frequencies is given. Using laser‐based ultrasonic techniques, we experimentally investigate some properties of these ZGV Lamb modes: resonance, backward wave propagation, interference between backward and forward waves. Experiments performed with materials of various Poisson's ratio demonstrate that the resonance spectrum of an unloaded elastic plate, locally excited by a laser pulse, is dominated by the ZGV Lamb modes. From these local resonance frequencies, thickness variations can be measured accurately and material properties like the Poisson's ratio, bulk acoustic wave velocities or material attenuation can be determined without any mechanical contact.
- 1 February 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 123 (2) , 599-601
Stresses and displacements for some Rayleigh-type surface acoustic waves propagating on an anisotropic half space
Specific relations between mechanical displacements and stresses for Rayleigh-type surface acoustic waves propagating on an anisotropic half space are demonstrated. For 16 symmetry configurations belonging to the orthorhombic, tetragonal, hexagonal and cubic systems, involving only two displacement and stress components, it is shown that the ratio between the shear and normal stresses inside the propagation media is equal to the ratio between the normal and in-plane displacement components at the free surface. This result generalizes the previous one obtained in the case of an isotropic solid [W. Hassan and P. B. Nagy, J. Acoust. Soc. Am. 104, 3107–3110 (1998)].
- 1 February 2008
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 123 (2) , 599-601
Stresses and displacements for some Rayleigh-type surface acoustic waves propagating on an anisotropic half space
Specific relations between mechanical displacements and stresses for Rayleigh-type surface acoustic waves propagating on an anisotropic half space are demonstrated. For 16 symmetry configurations belonging to the orthorhombic, tetragonal, hexagonal and cubic systems, involving only two displacement and stress components, it is shown that the ratio between the shear and normal stresses inside the propagation media is equal to the ratio between the normal and in-plane displacement components at the free surface. This result generalizes the previous one obtained in the case of an isotropic solid [W. Hassan and P. B. Nagy, J. Acoust. Soc. Am. 104, 3107–3110 (1998)].
- 1 March 2007
- Published by Elsevier in Ultrasonics
- Vol. 46 (1) , 23-24
An improved approximation for the Rayleigh wave equation
- 1 March 2007
- Published by Elsevier in Ultrasonics
- Vol. 46 (1) , 23-24
An improved approximation for the Rayleigh wave equation
- 16 June 2003
- Published by AIP Publishing in Applied Physics Letters
- Vol. 82 (25) , 4608-4610
Analysis of surface acoustic wave propagation on a cylinder using laser ultrasonics
- 16 June 2003
- Published by AIP Publishing in Applied Physics Letters
- Vol. 82 (25) , 4608-4610
Analysis of surface acoustic wave propagation on a cylinder using laser ultrasonics
- 1 April 2001
- Published by Elsevier in Ultrasonics
- Vol. 39 (3) , 223-225
A study of the secular equation for Rayleigh waves using the root locus method
- 1 April 2001
- Published by Elsevier in Ultrasonics
- Vol. 39 (3) , 223-225
A study of the secular equation for Rayleigh waves using the root locus method
- 1 September 2000
- Published by Elsevier in Ultrasonics
- Vol. 38 (9) , 891-895
Experimental and theoretical waveforms of Rayleigh waves generated by a thermoelastic laser line source
- 1 September 2000
- Published by Elsevier in Ultrasonics
- Vol. 38 (9) , 891-895
Experimental and theoretical waveforms of Rayleigh waves generated by a thermoelastic laser line source
- 29 August 1994
- Published by AIP Publishing in Applied Physics Letters
- Vol. 65 (9) , 1091-1093
Giant surface acoustic waves generated by a multiple beam laser: Application to the detection of surface breaking slots
Giant surface acoustic wave (SAW) pulses have been generated by implementing on the surface of a solid an array of strip thermoelastic sources. It is shown experimentally, with a 16-beam pulsed YAG laser, that the delays introduced between the laser emission times allow the constructive summation of the SAW pulses. Mechanical displacements larger than 20 nm on a steel sample and 50 nm on aluminum were detected by a heterodyne optical interferometer. Examples of noncontact and nondestructive detection of thin surface breaking slots are presented.
- 29 August 1994
- Published by AIP Publishing in Applied Physics Letters
- Vol. 65 (9) , 1091-1093
Giant surface acoustic waves generated by a multiple beam laser: Application to the detection of surface breaking slots
Giant surface acoustic wave (SAW) pulses have been generated by implementing on the surface of a solid an array of strip thermoelastic sources. It is shown experimentally, with a 16-beam pulsed YAG laser, that the delays introduced between the laser emission times allow the constructive summation of the SAW pulses. Mechanical displacements larger than 20 nm on a steel sample and 50 nm on aluminum were detected by a heterodyne optical interferometer. Examples of noncontact and nondestructive detection of thin surface breaking slots are presented.