E. Pinotti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
E. Pinotti has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
A. Borghesi
INFM and Università di Milano Bicocca, Dipartimento di Scienza dei Materiali, via Cozzi 53, 20125 Milano, Italy
4 shared publications- Adele Sassella
Department of Material Science, University of Milano-Bicocca, Via Cozzi 55, I-20125 Milano, Italy
4 shared publications M. Cartotti
INFM and Università di Milano Bicocca, Dipartimento di Scienza dei Materiali, via Cozzi 53, 20125 Milano, Italy
1 shared publication- Marcello Campione
University of Milano - Bicocca
1 shared publication R. Tubino
INFM and Dipartimento di Scienza dei Materiali, Università di Milano Bicocca, via Cozzi 53, I-201265 Milano, Italy
1 shared publication- Roberto Paolesse
University of Rome Tor Vergata
1 shared publication
Latest Publications
- 12 April 2004
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 22 (3) , 482-486
Thickness measurements by quartz microbalance during thin-film growth by organic-molecular-beam deposition
The problem of in situ monitoring the film thickness by quartz microbalance during vacuum deposition of organic-molecular semiconductors is addressed herein by setting a procedure for sensor calibration based on ex situ analysis of the deposited molecular film by atomic-force microscopy measurements. The procedure is applied to the growth of molecular-organic thin films on silica. Some physical parameters of the materials are deduced
- 12 April 2004
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 22 (3) , 482-486
Thickness measurements by quartz microbalance during thin-film growth by organic-molecular-beam deposition
The problem of in situ monitoring the film thickness by quartz microbalance during vacuum deposition of organic-molecular semiconductors is addressed herein by setting a procedure for sensor calibration based on ex situ analysis of the deposited molecular film by atomic-force microscopy measurements. The procedure is applied to the growth of molecular-organic thin films on silica. Some physical parameters of the materials are deduced
- 2 June 2003
- Published by Elsevier in Synthetic Metals
- Vol. 138 (1-2) , 15-19
Characterization of organic semiconductors by a large-signal capacitance–voltage method at high and low frequencies
- 2 June 2003
- Published by Elsevier in Synthetic Metals
- Vol. 138 (1-2) , 15-19
Characterization of organic semiconductors by a large-signal capacitance–voltage method at high and low frequencies
- 1 May 2001
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 19 (3) , 878-882
Thermal model of Knudsen cells for organic molecular beam deposition
Knudsen cells used for molecular beam deposition of organic materials are usually derived from the ones employed for conventional epitaxy of inorganic semiconductors. However, organic molecular materials need rather low evaporation temperatures and a very precise temperature control in the range from 100 to 400 °C. Therefore, a thermal model of the cell is needed, which, taking into account the peculiarity of organic molecular beam deposition, gives the thermal dynamics of the cell and can be used for developing accurate algorithms for thermal programming and control. In this article such a model is developed and fully assessed through a comparison with experimental results; on this basis, all information necessary for precisely controlling and programming Knudsen cells for organics is obtained.
- 1 May 2001
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 19 (3) , 878-882
Thermal model of Knudsen cells for organic molecular beam deposition
Knudsen cells used for molecular beam deposition of organic materials are usually derived from the ones employed for conventional epitaxy of inorganic semiconductors. However, organic molecular materials need rather low evaporation temperatures and a very precise temperature control in the range from 100 to 400 °C. Therefore, a thermal model of the cell is needed, which, taking into account the peculiarity of organic molecular beam deposition, gives the thermal dynamics of the cell and can be used for developing accurate algorithms for thermal programming and control. In this article such a model is developed and fully assessed through a comparison with experimental results; on this basis, all information necessary for precisely controlling and programming Knudsen cells for organics is obtained.
- 1 May 2001
- Published by Elsevier in Synthetic Metals
- Vol. 122 (1) , 169-171
Electrical characterization of organic semiconductors by transient current methods
- 1 May 2001
- Published by Elsevier in Synthetic Metals
- Vol. 122 (1) , 169-171
Electrical characterization of organic semiconductors by transient current methods