Kang-Hua Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kang-Hua Chen has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
H. C. Fang
State Key Laboratory for Powder Metallurgy, Central South University, Changsha 410083, Hunan (P. R. China)
3 shared publicationsS. Y. Chen
State Key Laboratory for Powder Metallurgy, Central South University, Changsha 410083, Hunan (P. R. China)
3 shared publicationsChang-Jun Zhu
Central South University
2 shared publicationsH. Chao
State Key Laboratory for Powder Metallurgy, Central South University, Changsha, Hunan 410083 (P.R. China)
2 shared publications- Changjun Zhu
Light Alloy Research Institute, Central South University, Changsha 410083, China
1 shared publication Chen-Xi Pan
Central South University
1 shared publication
Latest Publications
- Open Access
Mesomechanical Modeling and Numerical Simulation of the Diffraction Elastic Constants for Ti6Al4V Polycrystalline Alloy
A mesoscopic mechanical model based on the Mori-Tanaka method and Eshelby’s inclusion theory was presented to investigate the uniform elastic deformation behavior of Ti6Al4V with β-Ti and α-Ti phases. In particular, elastic mechanics field equations of inclusion and matrix phases were established separately, and several crystal plane diffraction elastic constants were predicted under uniaxial loading in this model. The results demonstrated that diffracted crystal plane elastic constants diversified with the elastic stiffness of the composition phase. In consequence, elastic deformation of one particular phase is related to the constraint of the whole deformation of all the phases constituting the materials. In this work, diffracted crystal plane elastic constants corresponding to different phases exert a substantial role in the determination of stresses by diffraction methods. Several numerical simulation results were compared and discussed.
Open AccessMesomechanical Modeling and Numerical Simulation of the Diffraction Elastic Constants for Ti6Al4V Polycrystalline Alloy
A mesoscopic mechanical model based on the Mori-Tanaka method and Eshelby’s inclusion theory was presented to investigate the uniform elastic deformation behavior of Ti6Al4V with β-Ti and α-Ti phases. In particular, elastic mechanics field equations of inclusion and matrix phases were established separately, and several crystal plane diffraction elastic constants were predicted under uniaxial loading in this model. The results demonstrated that diffracted crystal plane elastic constants diversified with the elastic stiffness of the composition phase. In consequence, elastic deformation of one particular phase is related to the constraint of the whole deformation of all the phases constituting the materials. In this work, diffracted crystal plane elastic constants corresponding to different phases exert a substantial role in the determination of stresses by diffraction methods. Several numerical simulation results were compared and discussed.
- 1 March 2018
- Published by Springer Nature in Journal of Central South University
- Vol. 25 (3) , 506-515
Microstructure, mechanical properties, and milling performance of arc-PVD AlTiN-Cu and AlTiN/AlTiN-Cu coatings
- 1 March 2018
- Published by Springer Nature in Journal of Central South University
- Vol. 25 (3) , 506-515
Microstructure, mechanical properties, and milling performance of arc-PVD AlTiN-Cu and AlTiN/AlTiN-Cu coatings
- 1 April 2013
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 23 (4) , 956-963
Effect of initial microstructure on hot workability of 7085 aluminum alloy
- 1 April 2013
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 23 (4) , 956-963
Effect of initial microstructure on hot workability of 7085 aluminum alloy
- 12 March 2012
- Published by Wiley in Materials and Corrosion
- Vol. 63 (3) , 254-258
Effect of the deformation on the stress–corrosion cracking of Al–Zn–Mg–Cu alloys
The effect of deformation on the stress–corrosion cracking (SCC) of Al–Zn–Mg–Cu alloys is studied by slow strain rate technique (SSRT) and bolt‐loaded double cantilever beam (DCB) tests. Results show that with the deformation increasing, the undissolved particles and subgrain size decrease whereas the fraction of recrystallization increases after solution treatment. The susceptibility to SCC by SSRT and DCB tests varies on different deformation amount alloy, in which cause is discussed.
- 12 March 2012
- Published by Wiley in Materials and Corrosion
- Vol. 63 (3) , 254-258
Effect of the deformation on the stress–corrosion cracking of Al–Zn–Mg–Cu alloys
The effect of deformation on the stress–corrosion cracking (SCC) of Al–Zn–Mg–Cu alloys is studied by slow strain rate technique (SSRT) and bolt‐loaded double cantilever beam (DCB) tests. Results show that with the deformation increasing, the undissolved particles and subgrain size decrease whereas the fraction of recrystallization increases after solution treatment. The susceptibility to SCC by SSRT and DCB tests varies on different deformation amount alloy, in which cause is discussed.
- 1 April 2011
- Published by Springer Nature in Journal of Central South University
- Vol. 18 (2) , 310-313
Effect of Al and Si additions on microstructure and mechanical properties of TiN coatings
- 1 April 2011
- Published by Springer Nature in Journal of Central South University
- Vol. 18 (2) , 310-313
Effect of Al and Si additions on microstructure and mechanical properties of TiN coatings
- 4 January 2011
- Published by Wiley in Materials and Corrosion
- Vol. 62 (1) , 35-40
The effect of recrystallization on corrosion and electrochemical behavior of 7150 Al alloy
By weight loss, potentiodynamic polarization, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS) techniques complemented by optical and scanning electron microscopy observations, the effect of recrystallization on the corrosion, and electrochemical behavior of 7150 Al alloy was studied. The results indicated that the high recrystallization fraction 7150‐1# was worse than the low recrystallization fraction 7150‐2# on corrosion resistance. The analysis of EIS indicated that 7150‐1# exhibited obvious pitting corrosion at 5 h immersion time, whereas 7150‐2# showed no obvious pitting corrosion even at 33 h. The corrosion route developed along the grain boundary of recrystallization grains, not along the grain boundary of unrecrystallization grains.
- 4 January 2011
- Published by Wiley in Materials and Corrosion
- Vol. 62 (1) , 35-40
The effect of recrystallization on corrosion and electrochemical behavior of 7150 Al alloy
By weight loss, potentiodynamic polarization, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS) techniques complemented by optical and scanning electron microscopy observations, the effect of recrystallization on the corrosion, and electrochemical behavior of 7150 Al alloy was studied. The results indicated that the high recrystallization fraction 7150‐1# was worse than the low recrystallization fraction 7150‐2# on corrosion resistance. The analysis of EIS indicated that 7150‐1# exhibited obvious pitting corrosion at 5 h immersion time, whereas 7150‐2# showed no obvious pitting corrosion even at 33 h. The corrosion route developed along the grain boundary of recrystallization grains, not along the grain boundary of unrecrystallization grains.
- 2 September 2010
- Published by Wiley in Materials and Corrosion
- Vol. 61 (9) , 783-789
EIS study on pitting corrosion of 7150 aluminum alloy in sodium chloride and hydrochloric acid solution
The pitting corrosion behavior of 7150 aluminum alloy was studied by electrochemical impedance spectroscopy (EIS) in the sodium chloride and hydrochloric acid solution. Based on EIS features and corrosion morphologies as well as corrosion potential, the process of pitting corrosion could be clearly divided into four stages: at the first stage, the Nyquist diagram was composed of two overlapping capacitive loops at the high‐medial frequency and one inductive loop at the low frequency. At the second stage (metastable pits developing stage), there existed one small capacitive loop at the high frequency and one big capacitive loop at the medial frequency. At the third stage (stable pits developing stage), two time constants were more clearly distinguished, corresponding to two obvious capacitive loops. At the fourth stage, there appeared one capacitive loop, attributing to uniform corrosion. An equivalent circuit was designed to fit EIS, and the experimental results and the fitted results had good correspondence.
- 2 September 2010
- Published by Wiley in Materials and Corrosion
- Vol. 61 (9) , 783-789
EIS study on pitting corrosion of 7150 aluminum alloy in sodium chloride and hydrochloric acid solution
The pitting corrosion behavior of 7150 aluminum alloy was studied by electrochemical impedance spectroscopy (EIS) in the sodium chloride and hydrochloric acid solution. Based on EIS features and corrosion morphologies as well as corrosion potential, the process of pitting corrosion could be clearly divided into four stages: at the first stage, the Nyquist diagram was composed of two overlapping capacitive loops at the high‐medial frequency and one inductive loop at the low frequency. At the second stage (metastable pits developing stage), there existed one small capacitive loop at the high frequency and one big capacitive loop at the medial frequency. At the third stage (stable pits developing stage), two time constants were more clearly distinguished, corresponding to two obvious capacitive loops. At the fourth stage, there appeared one capacitive loop, attributing to uniform corrosion. An equivalent circuit was designed to fit EIS, and the experimental results and the fitted results had good correspondence.
- 1 August 2006
- Published by Springer Nature in Journal of Central South University of Technology
- Vol. 13 (4) , 325-331
A mesomechanical ductility model of SiCp/Al composite
- 1 August 2006
- Published by Springer Nature in Journal of Central South University of Technology
- Vol. 13 (4) , 325-331
A mesomechanical ductility model of SiCp/Al composite