T. S. Sidhu
Research Subjects
T. S. Sidhu has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
R. D. Agrawal
Indian Institute of Technology Roorkee
7 shared publicationsS. Prakash
Indian Institute of Technology Roorkee
7 shared publications- Tarun Goyal
Department of Mechanical Engineering, I K Gujral Punjab Technical University, Jalandhar, India
4 shared publications - Ravinderjit Singh Walia
Punjab Engineering College (Deemed to be University)
3 shared publications A. Malik
Indian Institute of Technology Roorkee
1 shared publicationRamesh Bhagat
Shaheed Bhagat Singh College of Engineering and Technology
1 shared publication
Latest Publications
- 1 July 2014
- Published by IGI Global Scientific Publishing in International Journal of Surface Engineering and Interdisciplinary Materials Science
- Vol. 2 (2) , 23-33
Taguchi Based Optimization for Micro Hardness of Cold Spray Coating Process
In this paper, low pressure cold spray process has been employed to produce coatings on three different substrates. The experiments have been designed using Taguchi L 18 array where the input parameters have been selected as the type of feed arrangement, substrate material, stagnation temperature, stagnation pressure of the compressed gas and stand-off distance. The effect of these key parameters on raw data and Signal to Noise (S/N) ratio for micro hardness of low pressure cold spray process has been studied. The coatings were successfully developed on the substrates and the micro hardness of the so produced coatings has been measured. The results show that a high value of micro hardness can be obtained by selecting the input parameters which increases the impact velocity of the striking particles. These high velocity impacting particles produces a peening effect to already attached powder particles thereby increasing the micro hardness of obtained coatings. It is seen that the significant process parameters are type of powder feeding arrangement, substrate material, stand-off distance stagnation pressure of carrier gas and stagnation temperature of the carrier gas.
- 1 July 2014
- Published by IGI Global Scientific Publishing in International Journal of Surface Engineering and Interdisciplinary Materials Science
- Vol. 2 (2) , 23-33
Taguchi Based Optimization for Micro Hardness of Cold Spray Coating Process
In this paper, low pressure cold spray process has been employed to produce coatings on three different substrates. The experiments have been designed using Taguchi L 18 array where the input parameters have been selected as the type of feed arrangement, substrate material, stagnation temperature, stagnation pressure of the compressed gas and stand-off distance. The effect of these key parameters on raw data and Signal to Noise (S/N) ratio for micro hardness of low pressure cold spray process has been studied. The coatings were successfully developed on the substrates and the micro hardness of the so produced coatings has been measured. The results show that a high value of micro hardness can be obtained by selecting the input parameters which increases the impact velocity of the striking particles. These high velocity impacting particles produces a peening effect to already attached powder particles thereby increasing the micro hardness of obtained coatings. It is seen that the significant process parameters are type of powder feeding arrangement, substrate material, stand-off distance stagnation pressure of carrier gas and stagnation temperature of the carrier gas.
- 29 April 2014
- Published by Springer Nature
- p. 353-364
Investigation on Process Parameter Optimization for Coating Density and Microhardness of Cold-Sprayed Coatings
- 29 April 2014
- Published by Springer Nature
- p. 353-364
Investigation on Process Parameter Optimization for Coating Density and Microhardness of Cold-Sprayed Coatings
- 22 March 2012
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 64 (5-8) , 903-914
Multi-response optimization of low-pressure cold-sprayed coatings through Taguchi method and utility concept
- 22 March 2012
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 64 (5-8) , 903-914
Multi-response optimization of low-pressure cold-sprayed coatings through Taguchi method and utility concept
- 27 September 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 60 (5-8) , 611-623
Surface roughness optimization of cold-sprayed coatings using Taguchi method
- 27 September 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 60 (5-8) , 611-623
Surface roughness optimization of cold-sprayed coatings using Taguchi method
- 1 April 2009
- Published by Springer Nature in Sādhanā
- Vol. 34 (2) , 299-307
Erosion-corrosion behaviour of Ni-based superalloy Superni-75 in the real service environment of the boiler
- 1 April 2009
- Published by Springer Nature in Sādhanā
- Vol. 34 (2) , 299-307
Erosion-corrosion behaviour of Ni-based superalloy Superni-75 in the real service environment of the boiler
- 10 October 2007
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 16 (5-6) , 844-849
Oxidation and Hot Corrosion Resistance of HVOF WC-NiCrFeSiB Coating on Ni- and Fe-based Superalloys at 800 °C
- 10 October 2007
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 16 (5-6) , 844-849
Oxidation and Hot Corrosion Resistance of HVOF WC-NiCrFeSiB Coating on Ni- and Fe-based Superalloys at 800 °C
- 18 January 2007
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 38 (1) , 77-85
Study of Molten Salt Corrosion of High Velocity Oxy-Fuel Sprayed Cermet and Nickel-Based Coatings at 900 °C
- 18 January 2007
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 38 (1) , 77-85
Study of Molten Salt Corrosion of High Velocity Oxy-Fuel Sprayed Cermet and Nickel-Based Coatings at 900 °C
- 1 December 2006
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 15 (4) , 811-816
Characterizations and Hot Corrosion Resistance of Cr3C2-NiCr Coating on Ni-Base Superalloys in an Aggressive Environment
- 1 December 2006
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 15 (4) , 811-816
Characterizations and Hot Corrosion Resistance of Cr3C2-NiCr Coating on Ni-Base Superalloys in an Aggressive Environment
- 1 September 2006
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 15 (3) , 387-399
Hot Corrosion Resistance of High-Velocity Oxyfuel Sprayed Coatings on a Nickel-Base Superalloy in Molten Salt Environment
- 1 September 2006
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 15 (3) , 387-399
Hot Corrosion Resistance of High-Velocity Oxyfuel Sprayed Coatings on a Nickel-Base Superalloy in Molten Salt Environment