Odd Sture Hopperstad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Odd Sture Hopperstad has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Tore Børvik
Norwegian University of Science and Technology
28 shared publications David Morin
8 shared publications- Lars Edvard Blystad Dæhli
Structural Impact Laboratory (SIMLab), Department of Structural Engineering, NTNU - Norwegian University of Science and Technology, Trondheim, Norway
5 shared publications - Susanne Thomesen
Structural Impact Laboratory (SIMLab), Department of Structural Engineering, NTNU—Norwegian University of Science and Technology, NO-7034 Trondheim, Norway
5 shared publications - Jonas Rudshaug
Norwegian Defence Estates Agency
4 shared publications Arild Holm Clausen
3 shared publications
Latest Publications
- Open Access
- 5 May 2026
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 119
Modelling of ductile fracture in stainless steel combining porous plasticity and phase-field models
- 5 May 2026
- Published by Elsevier in European Journal of Mechanics - A/Solids
- Vol. 119
Open AccessModelling of ductile fracture in stainless steel combining porous plasticity and phase-field models
- 16 January 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1175, 1-6
Thermomechanical Testing and Precipitation Modelling of Al-Mg-Si Alloys for Hot Forming Applications
Thermomechanical tension tests were conducted on an Al-Mg-Si alloy at temperatures of 250°C, 350°C, and 450°C, with displacement rates of 2, 20, and 200 mm/s. The tests utilized an axisymmetric specimen with a diameter of 6 mm and a parallel length of 91 mm. Net axial stress versus logarithmic strain curves beyond diffuse necking were generated from the force measurements combined with edge tracing using synchronized images captured by a digital camera. Transmission electron microscopy (TEM) analyses were conducted on selected samples extracted near the fracture surface after testing and cooling to room temperature. After testing at 450°C, overaged needle precipitates were nucleated in bulk and on dispersoids. The dislocation density was low, but sub-grains of one to a few micrometres were observed. In contrast, after testing at 250°C, fine needle precipitates were nucleated in the bulk and on dislocations. A high dislocation density was found, with no subgrain formation. A combined precipitation, yield strength, and work hardening model for Al-Mg-Si alloys, known as NaMo, was finally employed to simulate the evolution of the precipitate structure and the stress-strain behaviour in the thermomechanical tension tests. In the model, variables representing the instantaneous state of the precipitate structure are predicted and used to calculate the corresponding yield strength and work hardening rate incorporating the effects of strain rate and temperature. A comparison between the calculated and measured yield stresses for small plastic strains showed good agreement.
- 16 January 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1175, 1-6
Thermomechanical Testing and Precipitation Modelling of Al-Mg-Si Alloys for Hot Forming Applications
Thermomechanical tension tests were conducted on an Al-Mg-Si alloy at temperatures of 250°C, 350°C, and 450°C, with displacement rates of 2, 20, and 200 mm/s. The tests utilized an axisymmetric specimen with a diameter of 6 mm and a parallel length of 91 mm. Net axial stress versus logarithmic strain curves beyond diffuse necking were generated from the force measurements combined with edge tracing using synchronized images captured by a digital camera. Transmission electron microscopy (TEM) analyses were conducted on selected samples extracted near the fracture surface after testing and cooling to room temperature. After testing at 450°C, overaged needle precipitates were nucleated in bulk and on dispersoids. The dislocation density was low, but sub-grains of one to a few micrometres were observed. In contrast, after testing at 250°C, fine needle precipitates were nucleated in the bulk and on dislocations. A high dislocation density was found, with no subgrain formation. A combined precipitation, yield strength, and work hardening model for Al-Mg-Si alloys, known as NaMo, was finally employed to simulate the evolution of the precipitate structure and the stress-strain behaviour in the thermomechanical tension tests. In the model, variables representing the instantaneous state of the precipitate structure are predicted and used to calculate the corresponding yield strength and work hardening rate incorporating the effects of strain rate and temperature. A comparison between the calculated and measured yield stresses for small plastic strains showed good agreement.
- Open Access
- 23 December 2025
- Published by Elsevier in Acta Astronautica
- Vol. 241, 61-84
Hypervelocity impact on Whipple shields with varying bumper material at 3 and 7 km/s: A numerical study using a coupled FEM/DEM method
- 23 December 2025
- Published by Elsevier in Acta Astronautica
- Vol. 241, 61-84
Open AccessHypervelocity impact on Whipple shields with varying bumper material at 3 and 7 km/s: A numerical study using a coupled FEM/DEM method
- Open Access
- 25 June 2025
- Published by Springer Nature in Meccanica
- Vol. 60 (8) , 2151-2175
A variational phase-field model for ductile fracture depending on hydrostatic stresses
We model ductile fracture for geometrically linear deformations by coupling plasticity and phase-field fracture models in a variationally consistent framework. The main aim of the proposed model is to account for the effect of stress triaxiality, in order to accurately reproduce ductile fracture, in particular, the instant and location of fracture initiation. For this purpose, we couple the modified Cam-Clay plasticity model with a phase-field fracture model. We study the behaviour of the model analytically in terms of homogeneous material responses, and numerically on plane-strain and axisymmetric specimens under tension with different notches.
- 25 June 2025
- Published by Springer Nature in Meccanica
- Vol. 60 (8) , 2151-2175
Open AccessA variational phase-field model for ductile fracture depending on hydrostatic stresses
We model ductile fracture for geometrically linear deformations by coupling plasticity and phase-field fracture models in a variationally consistent framework. The main aim of the proposed model is to account for the effect of stress triaxiality, in order to accurately reproduce ductile fracture, in particular, the instant and location of fracture initiation. For this purpose, we couple the modified Cam-Clay plasticity model with a phase-field fracture model. We study the behaviour of the model analytically in terms of homogeneous material responses, and numerically on plane-strain and axisymmetric specimens under tension with different notches.
- Open Access
A variational phase-field model for ductile fracture depending on hydrostatic stresses
We model ductile fracture for geometrically linear deformations by coupling plasticity and phase-field fracture models in a variationally consistent framework. The main aim of the proposed model is to account for the effect of stress triaxiality, in order to accurately reproduce ductile fracture, in particular, the instant and location of fracture initiation. For this purpose, we couple the modified Cam-Clay plasticity model with a phase-field fracture model. We study the behaviour of the model analytically in terms of homogeneous material responses, and numerically on plane-strain and axisymmetric specimens under tension with different notches.
Open AccessA variational phase-field model for ductile fracture depending on hydrostatic stresses
We model ductile fracture for geometrically linear deformations by coupling plasticity and phase-field fracture models in a variationally consistent framework. The main aim of the proposed model is to account for the effect of stress triaxiality, in order to accurately reproduce ductile fracture, in particular, the instant and location of fracture initiation. For this purpose, we couple the modified Cam-Clay plasticity model with a phase-field fracture model. We study the behaviour of the model analytically in terms of homogeneous material responses, and numerically on plane-strain and axisymmetric specimens under tension with different notches.
- Open Access
- 24 May 2025
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 325
Tensile ductility of an aluminium alloy: Experiments and simulations with a porous plasticity model
- 24 May 2025
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 325
Open AccessTensile ductility of an aluminium alloy: Experiments and simulations with a porous plasticity model
- Open Access
- 20 May 2025
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 202
Finite element modeling of porous ductile solids with non-uniform void size distributions
- 20 May 2025
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 202
Open AccessFinite element modeling of porous ductile solids with non-uniform void size distributions
- Open Access
- 2 April 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 203
Hypervelocity impact on Whipple shields with varying bumper material at 3 and 7 km/s: An experimental study
- 2 April 2025
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 203
Open AccessHypervelocity impact on Whipple shields with varying bumper material at 3 and 7 km/s: An experimental study
- Open Access
- 25 March 2025
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 33 (1)
Study of lattice structure anisotropy by crystal elasticity and plasticity FE simulations
- 25 March 2025
- Published by Taylor & Francis in Mechanics of Advanced Materials and Structures
- Vol. 33 (1)
Open AccessStudy of lattice structure anisotropy by crystal elasticity and plasticity FE simulations
- Open Access
- 19 November 2024
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 308
Ductile failure by strain localisation: A computational study of materials and structures subjected to highly non-proportional load histories
- 19 November 2024
- Published by Elsevier in International Journal of Solids and Structures
- Vol. 308
Open AccessDuctile failure by strain localisation: A computational study of materials and structures subjected to highly non-proportional load histories