Manjusri Misra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Manjusri Misra has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Amar K. Mohanty
Michigan State University
5 shared publicationsLawrence T. Drzal
Michigan State University
5 shared publicationsA. K. Mohanty
School of Packaging, 130 Packaging Building, Michigan State University, East Lansing, Michigan 48824
2 shared publicationsGeeta Mehta
Michigan State University
2 shared publicationsL. T. Drzal
Composite Materials and Structures Center, 2100 Engineering Building, Michigan State University, East Lansing, Michigan 48824
2 shared publicationsM. S. Huda
Composite Materials and Structures Center, 2100 Engineering Building, Michigan State University, East Lansing, Michigan 48824
2 shared publications
Latest Publications
- 28 September 2006
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 102 (5) , 4856-4869
Wood‐fiber‐reinforced poly(lactic acid) composites: Evaluation of the physicomechanical and morphological properties
This article presents the results of a study of the processing and physicomechanical properties of environmentally friendly wood‐fiber‐reinforced poly(lactic acid) composites that were produced with a microcompounding molding system. Wood‐fiber‐reinforced polypropylene composites were also processed under similar conditions and were compared to wood‐fiber‐reinforced poly(lactic acid) composites. The mechanical, thermomechanical, and morphological properties of these composites were studied. In terms of the mechanical properties, the wood‐fiber‐reinforced poly(lactic acid) composites were comparable to conventional polypropylene‐based thermoplastic composites. The mechanical properties of the wood‐fiber‐reinforced poly(lactic acid) composites were significantly higher than those of the virgin resin. The flexural modulus (8.9 GPa) of the wood‐fiber‐reinforced poly(lactic acid) composite (30 wt % fiber) was comparable to that of traditional (i.e., wood‐fiber‐reinforced polypropylene) composites (3.4 GPa). The incorporation of the wood fibers into poly(lactic acid) resulted in a considerable increase in the storage modulus (stiffness) of the resin. The addition of the maleated polypropylene coupling agent improved the mechanical properties of the composites. Microstructure studies using scanning electron microscopy indicated significant interfacial bonding between the matrix and the wood fibers. The specific performance evidenced by the wood‐fiber‐reinforced poly(lactic acid) composites may hint at potential applications in, for example, the automotive and packaging industries. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4856–4869, 2006
- 28 September 2006
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 102 (5) , 4856-4869
Wood‐fiber‐reinforced poly(lactic acid) composites: Evaluation of the physicomechanical and morphological properties
This article presents the results of a study of the processing and physicomechanical properties of environmentally friendly wood‐fiber‐reinforced poly(lactic acid) composites that were produced with a microcompounding molding system. Wood‐fiber‐reinforced polypropylene composites were also processed under similar conditions and were compared to wood‐fiber‐reinforced poly(lactic acid) composites. The mechanical, thermomechanical, and morphological properties of these composites were studied. In terms of the mechanical properties, the wood‐fiber‐reinforced poly(lactic acid) composites were comparable to conventional polypropylene‐based thermoplastic composites. The mechanical properties of the wood‐fiber‐reinforced poly(lactic acid) composites were significantly higher than those of the virgin resin. The flexural modulus (8.9 GPa) of the wood‐fiber‐reinforced poly(lactic acid) composite (30 wt % fiber) was comparable to that of traditional (i.e., wood‐fiber‐reinforced polypropylene) composites (3.4 GPa). The incorporation of the wood fibers into poly(lactic acid) resulted in a considerable increase in the storage modulus (stiffness) of the resin. The addition of the maleated polypropylene coupling agent improved the mechanical properties of the composites. Microstructure studies using scanning electron microscopy indicated significant interfacial bonding between the matrix and the wood fibers. The specific performance evidenced by the wood‐fiber‐reinforced poly(lactic acid) composites may hint at potential applications in, for example, the automotive and packaging industries. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4856–4869, 2006
- 30 August 2006
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 14 (4) , 359-368
Effect of Accelerated Weathering on Biocomposites Processed by SMC and Compression Molding
- 30 August 2006
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 14 (4) , 359-368
Effect of Accelerated Weathering on Biocomposites Processed by SMC and Compression Molding
- 1 January 2006
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 14 (1) , 27-35
Effect of Sequential Mixing and Compounding Conditions on Cellulose Acetate/Layered Silicate Nanocomposites
- 1 January 2006
- Published by Springer Nature in Journal of Polymers and the Environment
- Vol. 14 (1) , 27-35
Effect of Sequential Mixing and Compounding Conditions on Cellulose Acetate/Layered Silicate Nanocomposites
- 22 December 2005
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 291 (1) , 90-95
A Solvent Free Graft Copolymerization of Maleic Anhydride onto Cellulose Acetate Butyrate Bioplastic by Reactive Extrusion
Summary: Interfacial adhesion between fibers and matrix is a crucial factor for effective stress transfer from matrix to fiber; especially in short fiber reinforced composite systems. The use of a chemical compatibilizer is an efficient means to achieve such adhesion. Maleic anhydride‐grafted‐cellulose acetate butyrate (CAB‐g‐MA) is one such compatibilizer which can be used in biocomposite fabrication, and this has been synthesized in our laboratory by utilizing a twin‐screw reactive extrusion process in the presence of a free radical initiator (2,5‐dimethyl‐2,5‐di(tert‐butylperoxy)hexane). The unique feature of this process is its solvent‐free approach for grafting of maleic anhydride onto CAB, without hydroxyl group protection. CAB‐g‐MA was characterized using FTIR as well as by a non‐aqueous titration method. The effects of initiator and monomer concentrations and various processing conditions on the graft content were also investigated. The preliminary results show that by adding approximately 10 wt.‐% of CAB‐g‐MA into a plasticized cellulose acetate butyrate (TEB)‐industrial hemp fiber biocomposites system, an improvement in tensile strength (20%) and in tensile modulus (45%) were obtained. These results are promising in that they pave the way for future studies involving the use of CAB‐g‐MA as a suitable compatibilizer for cellulose ester‐natural fiber biocomposites. magnified image
- 22 December 2005
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 291 (1) , 90-95
A Solvent Free Graft Copolymerization of Maleic Anhydride onto Cellulose Acetate Butyrate Bioplastic by Reactive Extrusion
Summary: Interfacial adhesion between fibers and matrix is a crucial factor for effective stress transfer from matrix to fiber; especially in short fiber reinforced composite systems. The use of a chemical compatibilizer is an efficient means to achieve such adhesion. Maleic anhydride‐grafted‐cellulose acetate butyrate (CAB‐g‐MA) is one such compatibilizer which can be used in biocomposite fabrication, and this has been synthesized in our laboratory by utilizing a twin‐screw reactive extrusion process in the presence of a free radical initiator (2,5‐dimethyl‐2,5‐di(tert‐butylperoxy)hexane). The unique feature of this process is its solvent‐free approach for grafting of maleic anhydride onto CAB, without hydroxyl group protection. CAB‐g‐MA was characterized using FTIR as well as by a non‐aqueous titration method. The effects of initiator and monomer concentrations and various processing conditions on the graft content were also investigated. The preliminary results show that by adding approximately 10 wt.‐% of CAB‐g‐MA into a plasticized cellulose acetate butyrate (TEB)‐industrial hemp fiber biocomposites system, an improvement in tensile strength (20%) and in tensile modulus (45%) were obtained. These results are promising in that they pave the way for future studies involving the use of CAB‐g‐MA as a suitable compatibilizer for cellulose ester‐natural fiber biocomposites. magnified image
- 18 November 2005
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 99 (3) , 1055-1068
Effect of fiber surface treatment on the properties of biocomposites from nonwoven industrial hemp fiber mats and unsaturated polyester resin
Biocomposites were made with nonwoven hemp mats and unsaturated polyester resin (UPE). The hemp fiber volume fraction was optimized by mechanical testing. The effect of four surface treatments of industrial hemp fibers on mechanical and thermal properties of biocomposites was studied. The treatments done were alkali treatment, silane treatment, UPE (matrix) treatment, and acrylonitrile treatment. Bending strength, modulus of elasticity, tensile strength, tensile modulus, impact strength, storage modulus, loss modulus, and tan δ were evaluated and compared for all composites. The mechanical as well as thermal properties of the biocomposites improved after surface treatments. The properties of the above biocomposites were also compared with E‐glass–mat composite. To achieve balance in properties, a hybrid composite of industrial hemp and glass fibers was made. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1055–1068, 2006
- 18 November 2005
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 99 (3) , 1055-1068
Effect of fiber surface treatment on the properties of biocomposites from nonwoven industrial hemp fiber mats and unsaturated polyester resin
Biocomposites were made with nonwoven hemp mats and unsaturated polyester resin (UPE). The hemp fiber volume fraction was optimized by mechanical testing. The effect of four surface treatments of industrial hemp fibers on mechanical and thermal properties of biocomposites was studied. The treatments done were alkali treatment, silane treatment, UPE (matrix) treatment, and acrylonitrile treatment. Bending strength, modulus of elasticity, tensile strength, tensile modulus, impact strength, storage modulus, loss modulus, and tan δ were evaluated and compared for all composites. The mechanical as well as thermal properties of the biocomposites improved after surface treatments. The properties of the above biocomposites were also compared with E‐glass–mat composite. To achieve balance in properties, a hybrid composite of industrial hemp and glass fibers was made. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1055–1068, 2006
- 1 August 2005
- Published by Springer Nature in Journal of Materials Science
- Vol. 40 (16) , 4221-4229
“Green” composites from recycled cellulose and poly(lactic acid): Physico-mechanical and morphological properties evaluation
- 1 August 2005
- Published by Springer Nature in Journal of Materials Science
- Vol. 40 (16) , 4221-4229
“Green” composites from recycled cellulose and poly(lactic acid): Physico-mechanical and morphological properties evaluation
- 2 November 2004
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 289 (11) , 955-974
A Review on Pineapple Leaf Fibers, Sisal Fibers and Their Biocomposites
Summary: The use of lignocellulosic fibers, pineapple leaf fiber (PALF) and sisal as reinforcements in thermoplastic and thermosetting resins for developing low cost and lightweight composites is an emerging field of research in polymer science and technology. Although, these biofibers have several advantages, such as low densities, low cost, nonabrasive nature, high filling level possible, low energy consumption, high specific properties, biodegradability, etc., over synthetic fibers, the absorption of moisture by untreated biofibers, poor wettability, and insufficient adhesion between the polymer matrix and fiber deteriorate the mechanical properties of composites made up of these biofibers. Therefore, the modification of these fibers is a key area of research at present to obtain optimum fiber‐matrix properties. This review article is concerned with the structure, composition and properties of PALF and sisal, the chemical modifications of these fibers and PALF/sisal‐reinforced thermosets, thermoplastics, rubber, cement, hybrids and biocomposites. Scanning electron micrograph of tensile fractured surface of alkali treated sisal fiber (magnification ×500). magnified image Scanning electron micrograph of tensile fractured surface of alkali treated sisal fiber (magnification ×500).
- 2 November 2004
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 289 (11) , 955-974
A Review on Pineapple Leaf Fibers, Sisal Fibers and Their Biocomposites
Summary: The use of lignocellulosic fibers, pineapple leaf fiber (PALF) and sisal as reinforcements in thermoplastic and thermosetting resins for developing low cost and lightweight composites is an emerging field of research in polymer science and technology. Although, these biofibers have several advantages, such as low densities, low cost, nonabrasive nature, high filling level possible, low energy consumption, high specific properties, biodegradability, etc., over synthetic fibers, the absorption of moisture by untreated biofibers, poor wettability, and insufficient adhesion between the polymer matrix and fiber deteriorate the mechanical properties of composites made up of these biofibers. Therefore, the modification of these fibers is a key area of research at present to obtain optimum fiber‐matrix properties. This review article is concerned with the structure, composition and properties of PALF and sisal, the chemical modifications of these fibers and PALF/sisal‐reinforced thermosets, thermoplastics, rubber, cement, hybrids and biocomposites. Scanning electron micrograph of tensile fractured surface of alkali treated sisal fiber (magnification ×500). magnified image Scanning electron micrograph of tensile fractured surface of alkali treated sisal fiber (magnification ×500).