Gene Kouba
Research Subjects
Gene Kouba has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Ovadia Shoham
The University of Tulsa
6 shared publications - Ram S. Mohan
The University of Tulsa
3 shared publications - Eduardo Pereyra
McDougall School of Petroleum Engineering, The University of Tulsa, Tulsa, OK 74104
2 shared publications - Luis E. Gomez
McDougall School of Petroleum Engineering, The University of Tulsa, Tulsa, OK 74104
2 shared publications - Shoubo Wang
McDougall School of Petroleum Engineering, The University of Tulsa, 800 S. Tucker Drive, Tulsa, OK 74104
2 shared publications - Hung Nguyen
Mem. ASME Department of Mechanical Engineering, The University of Tulsa, 800 S. Tucker Drive, Tulsa, OK 74104
1 shared publication
Latest Publications
- 9 April 2014
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 136 (2) , 022902
Experimental Investigations of Droplet Deposition and Coalescence in Curved Pipes
Even though there have been several studies conducted by the industry on the use of different inlet devices for gas–liquid separation, there have been limited laboratory and field evaluations on the use of external piping configurations as flow conditioning devices upstream of a separator inlet. The results of a systematic study of droplet deposition and coalescence in curved pipe and pipe fittings are reported in this paper. A facility has been designed consisting of two main test sections: a fixed horizontal straight pipe section and an interchangeable 180 deg return pipe section (or curved pipe section) of the same length. Both inlet and outlet to the 180 deg return are horizontal, but the plane of the 180 deg return pipe section can pivot about the axis of the inlet horizontal pipe to an angle as much as 10 deg downwards allowing downward flow in the return section. Various pipe fittings of different radius of curvature can be installed for comparison in the 180 deg return. Fittings evaluated in this study included: 180 deg pipe bend, short elbow bend (with standard radius of curvature of 1.5D), long elbow bend (with custom radius of curvature of 6D), target tee bend, and cushion tee bend. Experiments have been carried out using water and air, and varying gas velocities and liquid loadings. In order to compare the performance of geometries, Droplet Deposition Fractions (DDF) were measured in the horizontal straight pipe section and in the 180 deg return pipe section as a measure of coalescence efficiency. The results demonstrate that higher DDF occurs for curved fittings as compared to the straight pipe section. The short elbow bend has approximately 10% DDF higher, whereas long elbow bend along with 180 deg pipe bend perform better (by 15–20% DDF) than straight pipe. It was found that the cushion tee and target tee bends can coalesce droplets at lower gas velocities but break up droplets at higher gas velocities. Additionally, no significant differences between DDF's in three different inclination angles of a curved pipe were observed. It can be concluded that 180 deg pipe bend or two 6D long radius elbow bend can serve as a droplet coalescer; a pair of cushion tees or target tees can also work as coalescers at low kinetic energy but as atomizers at high kinetic energy.
- 9 April 2014
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 136 (2) , 022902
Experimental Investigations of Droplet Deposition and Coalescence in Curved Pipes
Even though there have been several studies conducted by the industry on the use of different inlet devices for gas–liquid separation, there have been limited laboratory and field evaluations on the use of external piping configurations as flow conditioning devices upstream of a separator inlet. The results of a systematic study of droplet deposition and coalescence in curved pipe and pipe fittings are reported in this paper. A facility has been designed consisting of two main test sections: a fixed horizontal straight pipe section and an interchangeable 180 deg return pipe section (or curved pipe section) of the same length. Both inlet and outlet to the 180 deg return are horizontal, but the plane of the 180 deg return pipe section can pivot about the axis of the inlet horizontal pipe to an angle as much as 10 deg downwards allowing downward flow in the return section. Various pipe fittings of different radius of curvature can be installed for comparison in the 180 deg return. Fittings evaluated in this study included: 180 deg pipe bend, short elbow bend (with standard radius of curvature of 1.5D), long elbow bend (with custom radius of curvature of 6D), target tee bend, and cushion tee bend. Experiments have been carried out using water and air, and varying gas velocities and liquid loadings. In order to compare the performance of geometries, Droplet Deposition Fractions (DDF) were measured in the horizontal straight pipe section and in the 180 deg return pipe section as a measure of coalescence efficiency. The results demonstrate that higher DDF occurs for curved fittings as compared to the straight pipe section. The short elbow bend has approximately 10% DDF higher, whereas long elbow bend along with 180 deg pipe bend perform better (by 15–20% DDF) than straight pipe. It was found that the cushion tee and target tee bends can coalesce droplets at lower gas velocities but break up droplets at higher gas velocities. Additionally, no significant differences between DDF's in three different inclination angles of a curved pipe were observed. It can be concluded that 180 deg pipe bend or two 6D long radius elbow bend can serve as a droplet coalescer; a pair of cushion tees or target tees can also work as coalescers at low kinetic energy but as atomizers at high kinetic energy.
- 19 March 2012
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 134 (2) , 023001
State of the Art of Experimental Studies and Predictive Methods for Slug Liquid Holdup
A summary of all available correlations and mechanistic models for the prediction of slug liquid holdup is presented. Additionally, an experimental data base for slug liquid holdup has been collected from available literature. A comparison between the predictions of available models and correlations against the data base is presented, identifying the range of applicability of the different methods. The correlations have been tuned against the new data by calculating new values of their constant parameters, showing an improved performance. Also, the uncertainties of the correlations parameters are evaluated and presented. A recommendation for the best method of predicting the slug liquid holdup is provided.
- 19 March 2012
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 134 (2) , 023001
State of the Art of Experimental Studies and Predictive Methods for Slug Liquid Holdup
A summary of all available correlations and mechanistic models for the prediction of slug liquid holdup is presented. Additionally, an experimental data base for slug liquid holdup has been collected from available literature. A comparison between the predictions of available models and correlations against the data base is presented, identifying the range of applicability of the different methods. The correlations have been tuned against the new data by calculating new values of their constant parameters, showing an improved performance. Also, the uncertainties of the correlations parameters are evaluated and presented. A recommendation for the best method of predicting the slug liquid holdup is provided.
- 1 January 2011
- Published by Springer Nature
- p. 299-311
Design and Performance of Gas–Liquid Cylindrical Cyclone/Slug Damper System
- 1 January 2011
- Published by Springer Nature
- p. 299-311
Design and Performance of Gas–Liquid Cylindrical Cyclone/Slug Damper System
- 1 January 2003
- Published by ASME International
- p. 1645-1656
The State-of-the-Art of Gas-Liquid Compact Separator Control Technology: From Lab to Field
Conventional gas-liquid separators are vessel-type with simple level, and pressure control since the residence time is large. Compact gas-liquid separators, such as Gas-Liquid Cylindrical Cyclone (GLCC©), have emerged recently as alternatives to reduce size and increase separation efficiency for offshore and subsea applications. As compared to the vessel-type separators, compact separators, are simple, low-cost, low-weight, require little maintenance and are easy to install and operate. However, the residence time of the GLCC is very small. Consequently, it can get upset easily due to high flow variations at the inlet, for example, slugging, without the aid of fast and accurate control systems. In the past, lack of understanding of control system dynamics and design tools have prevented this technology from fast field deployment. The objective of this study is to present a review of the compact gas-liquid separator (GLCC) control technology. This includes the development of control strategies, control system design, dynamic simulation, experimental investigation and field applications. The performance of compact gas-liquid separator (GLCC) strongly depends on the liquid level and/or separating pressure. In this investigation, several control strategies have been developed for field applications of gas-liquid compact separators. Especially, an optimal control strategy was developed for handling slug flow and optimizing the system performance in terms of reduced or eliminated liquid carry-over (LCO) or gas carry-under (GCU). The developed strategies have been used for the design of several GLCC applications, currently in operation in the field. Details of these applications are also presented. This study provides the state-of-the-art of gas-liquid compact separator control technology from the lab to field.
- 1 January 2003
- Published by ASME International
- p. 1645-1656
The State-of-the-Art of Gas-Liquid Compact Separator Control Technology: From Lab to Field
Conventional gas-liquid separators are vessel-type with simple level, and pressure control since the residence time is large. Compact gas-liquid separators, such as Gas-Liquid Cylindrical Cyclone (GLCC©), have emerged recently as alternatives to reduce size and increase separation efficiency for offshore and subsea applications. As compared to the vessel-type separators, compact separators, are simple, low-cost, low-weight, require little maintenance and are easy to install and operate. However, the residence time of the GLCC is very small. Consequently, it can get upset easily due to high flow variations at the inlet, for example, slugging, without the aid of fast and accurate control systems. In the past, lack of understanding of control system dynamics and design tools have prevented this technology from fast field deployment. The objective of this study is to present a review of the compact gas-liquid separator (GLCC) control technology. This includes the development of control strategies, control system design, dynamic simulation, experimental investigation and field applications. The performance of compact gas-liquid separator (GLCC) strongly depends on the liquid level and/or separating pressure. In this investigation, several control strategies have been developed for field applications of gas-liquid compact separators. Especially, an optimal control strategy was developed for handling slug flow and optimizing the system performance in terms of reduced or eliminated liquid carry-over (LCO) or gas carry-under (GCU). The developed strategies have been used for the design of several GLCC applications, currently in operation in the field. Details of these applications are also presented. This study provides the state-of-the-art of gas-liquid compact separator control technology from the lab to field.
- 1 October 1999
- Published by Society of Petroleum Engineers (SPE)
State-of-the-Art Simulator for Field Applications of Gas-Liquid Cylindrical Cyclone Separators
The Gas-Liquid Cylindrical Cyclone (GLCC(c)1) is an example of a compact separator which is simple, lightweight, and having low capital and operational costs. The GLCC(c) has a wide variety of potential applications, varying from only partial to complete phase separation. This paper presents a state-of-the-art simulator for GLCC(c) design and analysis, based on an improved mechanistic model, written in an Excel Visual-Basic(r) platform. The simulator has two components namely, design wizard code and performance code. The design wizard is used for performing the preliminary design of the GLCC(c), and the performance code enables detailed prediction of the complex hydrodynamic flow behavior in the GLCC(c). This user-friendly simulator incorporates the best available technology for the design of GLCC(c) separators for the industry. The simulator has been used to design over 100 GLCC(c) units operating in the USA and around the world. Details of successful field application of GLCC(c) separator for offshore Lake Maracaibo, PDVSA, Venezuela, (multiphase flow-metering loop), PETROBRAS, Brazil, (external pre-separation) ARCO, Alaska (gas knockout) and Minas, CPI, Indonesia (bulk separation/metering), are presented and discussed. These examples demonstrate the potential, advantages, and benefits offered by the GLCC(c) simulator for enhancing the utilization of compact separators in both offshore and onshore environments.1 GLCC(c) - Gas-Liquid Cylindrical Cyclone - copyright, The University of Tulsa, 1994.
- 1 October 1999
- Published by Society of Petroleum Engineers (SPE)
State-of-the-Art Simulator for Field Applications of Gas-Liquid Cylindrical Cyclone Separators
The Gas-Liquid Cylindrical Cyclone (GLCC(c)1) is an example of a compact separator which is simple, lightweight, and having low capital and operational costs. The GLCC(c) has a wide variety of potential applications, varying from only partial to complete phase separation. This paper presents a state-of-the-art simulator for GLCC(c) design and analysis, based on an improved mechanistic model, written in an Excel Visual-Basic(r) platform. The simulator has two components namely, design wizard code and performance code. The design wizard is used for performing the preliminary design of the GLCC(c), and the performance code enables detailed prediction of the complex hydrodynamic flow behavior in the GLCC(c). This user-friendly simulator incorporates the best available technology for the design of GLCC(c) separators for the industry. The simulator has been used to design over 100 GLCC(c) units operating in the USA and around the world. Details of successful field application of GLCC(c) separator for offshore Lake Maracaibo, PDVSA, Venezuela, (multiphase flow-metering loop), PETROBRAS, Brazil, (external pre-separation) ARCO, Alaska (gas knockout) and Minas, CPI, Indonesia (bulk separation/metering), are presented and discussed. These examples demonstrate the potential, advantages, and benefits offered by the GLCC(c) simulator for enhancing the utilization of compact separators in both offshore and onshore environments.1 GLCC(c) - Gas-Liquid Cylindrical Cyclone - copyright, The University of Tulsa, 1994.
- 1 July 1998
- Published by Society of Petroleum Engineers (SPE) in Journal of Petroleum Technology
- Vol. 50 (7)
State of the Art of Gas/Liquid Cylindrical-Cyclone Compact-Separator Technology
- 1 July 1998
- Published by Society of Petroleum Engineers (SPE) in Journal of Petroleum Technology
- Vol. 50 (7)
State of the Art of Gas/Liquid Cylindrical-Cyclone Compact-Separator Technology
- 1 November 1990
- Published by Society of Petroleum Engineers (SPE) in SPE Production Engineering
- Vol. 5 (04) , 373-380
A Nonintrusive Flowmetering Method for Two-Phase Intermittent Flow in Horizontal Pipes
- 1 November 1990
- Published by Society of Petroleum Engineers (SPE) in SPE Production Engineering
- Vol. 5 (04) , 373-380
A Nonintrusive Flowmetering Method for Two-Phase Intermittent Flow in Horizontal Pipes