Sergey V Malykhin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Sergey V Malykhin has a total of 100 co-authors. Here are the top co-authors by number of shared publications:
- Igor E. Garkusha
Kharkiv Institute of Physics and Technology
11 shared publications - Marek Jan Sadowski
International Scientific Committee for Dense Magnetized Plasmas 2 , 01-497 Warsaw, Poland
6 shared publications E Skladnik-Sadowska
National Centre for Nuclear Research (NCBJ), 05-400 Otwock, Poland
5 shared publications- S. V. Surovitskiy
National Technical University "Kharkiv Polytechnic Institute
5 shared publications V A Makhlaj
Institute of Plasma Physics, NSC ‘Kharkov Institute of Physics and Technology’, 61108, Kharkov, Ukraine
5 shared publicationsI Landman
National Technical University
4 shared publications
Latest Publications
- 14 April 2026
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
STRUCTURAL AND PHASE CHANGES IN Ti41Zr41Ni18 COATINGS DURING VACUUM ANNEALING
Structural and phase changes in the magnetron-deposited Ti41Zr41Ni18 coating during vacuum annealing at temperatures of 500 and 700 °C were studied with XRD, SEM, and TEM methods. It was found that after annealing at 500 °C for 4 h an icosahedral quasicrystalline phase was formed from the amorphous phase, as well as a columnar structure of the 2/1 crystalline approximant formed near the surface. A three-hour annealing at 700 °C promoted a volume-heterogeneous phase transformation of the quasicrystalline phase into three crystalline phases: α-Ti(Zr) solid solution, Laves phase (Ti,Zr)2Ni (C14 type) and the 2/1 crystalline approximant phase. The heterogeneity may be due to the development of internal stresses, the release of latent heat of transformation, and overheating of the phase reaction front.
- 14 April 2026
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
STRUCTURAL AND PHASE CHANGES IN Ti41Zr41Ni18 COATINGS DURING VACUUM ANNEALING
Structural and phase changes in the magnetron-deposited Ti41Zr41Ni18 coating during vacuum annealing at temperatures of 500 and 700 °C were studied with XRD, SEM, and TEM methods. It was found that after annealing at 500 °C for 4 h an icosahedral quasicrystalline phase was formed from the amorphous phase, as well as a columnar structure of the 2/1 crystalline approximant formed near the surface. A three-hour annealing at 700 °C promoted a volume-heterogeneous phase transformation of the quasicrystalline phase into three crystalline phases: α-Ti(Zr) solid solution, Laves phase (Ti,Zr)2Ni (C14 type) and the 2/1 crystalline approximant phase. The heterogeneity may be due to the development of internal stresses, the release of latent heat of transformation, and overheating of the phase reaction front.
- Open Access
- 1 November 2023
- Published by AIP Publishing in Low Temperature Physics
- Vol. 49 (11) , 1245-1249
Electrical resistivity of coatings of quasicrystalline and crystalline phases of the Ti—Zr—Ni system in the temperature range 4–300 K
The temperature dependence of the electrical resistivity in the temperature range from 4.4 to 300 K for Ti41Zr41Ni18 (at. %) thin coatings of different crystal perfection and phase composition was studied. The coatings were deposited by magnetron sputtering with subsequent vacuum annealing in various modes ensuring the formation of several heterophase combinations, which included 1/1 and 2/1 approximation phases, a quasicrystalline icosahedral phase, a Laves phase (Ti, Zr)2Ni, and an α-Ti (Zr) solid solution. The structure before and after annealing was studied by X-ray diffractometry. It was established that coatings with a predominant content of amorphous, quasicrystalline, or approximant 2/1 phases have a temperature coefficient of resistance less than zero, while samples with a predominance of crystalline phases demonstrate characteristic metallic conductivity. The temperature dependence of the electrical resistivity of the Ti41Zr41Ni18 quasicrystalline coating turned out to be similar to the dependence in bulk samples of the Ti40Zr40Ni20 composition. The electrical resistivity of the approximant 2/1 phase with a low content of the additional Laves phase in the film has an almost constant value in the entire investigated temperature range.
- 1 November 2023
- Published by AIP Publishing in Low Temperature Physics
- Vol. 49 (11) , 1245-1249
Open AccessElectrical resistivity of coatings of quasicrystalline and crystalline phases of the Ti—Zr—Ni system in the temperature range 4–300 K
The temperature dependence of the electrical resistivity in the temperature range from 4.4 to 300 K for Ti41Zr41Ni18 (at. %) thin coatings of different crystal perfection and phase composition was studied. The coatings were deposited by magnetron sputtering with subsequent vacuum annealing in various modes ensuring the formation of several heterophase combinations, which included 1/1 and 2/1 approximation phases, a quasicrystalline icosahedral phase, a Laves phase (Ti, Zr)2Ni, and an α-Ti (Zr) solid solution. The structure before and after annealing was studied by X-ray diffractometry. It was established that coatings with a predominant content of amorphous, quasicrystalline, or approximant 2/1 phases have a temperature coefficient of resistance less than zero, while samples with a predominance of crystalline phases demonstrate characteristic metallic conductivity. The temperature dependence of the electrical resistivity of the Ti41Zr41Ni18 quasicrystalline coating turned out to be similar to the dependence in bulk samples of the Ti40Zr40Ni20 composition. The electrical resistivity of the approximant 2/1 phase with a low content of the additional Laves phase in the film has an almost constant value in the entire investigated temperature range.
- Open Access
- 1 January 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 959 (1) , 012004
Materials surface damage and modification under high power plasma exposures
- 1 January 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 959 (1) , 012004
Open AccessMaterials surface damage and modification under high power plasma exposures
- Open Access
- 1 December 2016
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 9, 116-122
Damaging of tungsten and tungsten–tantalum alloy exposed in ITER ELM-like conditions
- 1 December 2016
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 9, 116-122
Open AccessDamaging of tungsten and tungsten–tantalum alloy exposed in ITER ELM-like conditions
- 1 August 2016
- Published by IOP Publishing in Physica Scripta
- Vol. 91 (9) , 094001
Simulation of plasma–surface interactions in a fusion reactor by means of QSPA plasma streams: recent results and prospects
This paper is devoted to plasma–surface interaction issues at high heat-loads which are typical for fusion reactors. For the International Thermonuclear Experimental Reactor (ITER), which is now under construction, the knowledge of erosion processes and the behaviour of various constructional materials under extreme conditions is a very critical issue, which will determine a successful realization of the project. The most important plasma–surface interaction (PSI) effects in 3D geometry have been studied using a QSPA Kh-50 powerful quasi-stationary plasma accelerator. Mechanisms of the droplet and dust generation have been investigated in detail. It was found that the droplets emission from castellated surfaces has a threshold character and a cyclic nature. It begins only after a certain number of the irradiating plasma pulses when molten and shifted material is accumulated at the edges of the castellated structure. This new erosion mechanism, connected with the edge effects, results in an increase in the size of the emitted droplets (as compared with those emitted from a flat surface). This mechanism can even induce the ejection of sub-mm particles. A concept of a new-generation QSPA facility, the current status of this device maintenance, and prospects for further experiments are also presented.
- 1 August 2016
- Published by IOP Publishing in Physica Scripta
- Vol. 91 (9) , 094001
Simulation of plasma–surface interactions in a fusion reactor by means of QSPA plasma streams: recent results and prospects
This paper is devoted to plasma–surface interaction issues at high heat-loads which are typical for fusion reactors. For the International Thermonuclear Experimental Reactor (ITER), which is now under construction, the knowledge of erosion processes and the behaviour of various constructional materials under extreme conditions is a very critical issue, which will determine a successful realization of the project. The most important plasma–surface interaction (PSI) effects in 3D geometry have been studied using a QSPA Kh-50 powerful quasi-stationary plasma accelerator. Mechanisms of the droplet and dust generation have been investigated in detail. It was found that the droplets emission from castellated surfaces has a threshold character and a cyclic nature. It begins only after a certain number of the irradiating plasma pulses when molten and shifted material is accumulated at the edges of the castellated structure. This new erosion mechanism, connected with the edge effects, results in an increase in the size of the emitted droplets (as compared with those emitted from a flat surface). This mechanism can even induce the ejection of sub-mm particles. A concept of a new-generation QSPA facility, the current status of this device maintenance, and prospects for further experiments are also presented.
- 24 March 2016
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Functional Materials
- Vol. 23 (4) , 179-183
On application of X-ray aproximation method for studying the substructure of sufficiently perfect samples
- 24 March 2016
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Functional Materials
- Vol. 23 (4) , 179-183
On application of X-ray aproximation method for studying the substructure of sufficiently perfect samples
- Open Access
- 24 March 2015
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 591
High power plasma interaction with tungsten grades in ITER relevant conditions
- 24 March 2015
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 591
Open AccessHigh power plasma interaction with tungsten grades in ITER relevant conditions
- 15 November 2014
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 59 (11) , 1620-1625
Changes in the structure and substructure of tungsten during irradiation by hydrogen plasma flows at the specific energy close to the heat loads on the ITER surface
The changes in the structure, the substructure, and the state of stress in the surface layers of tungsten targets and the cracking processes in them are studied in model experiments on irradiation by a hydrogen plasma in a quasi-stationary plasma accelerator QSPA Kh-50, which adequately reproduces the energy density and the edge localized mode (ELM) time in ITER. The plasma heat load is up to 1 MJ m−2, the pulse duration is 0.25 ms, and the maximum number of irradiating pulses of 150. The development of residual macrostresses from compression to tension is analyzed by X-ray diffraction, and their relation to cracking is shown. Irradiation is found to increase the lattice parameter of tungsten in the undeformable section from a 0 ≈ 0.31642 ± 0.00001 (initial state) to 0.31645 ± 0.00001 nm. The changes in the coherent scattering region and microstrains are estimated. The role of point defects and their complexes in the irradiation-assisted processes is established. A qualitative model is proposed to explain these changes.
- 15 November 2014
- Published by Pleiades Publishing Ltd in Technical Physics
- Vol. 59 (11) , 1620-1625
Changes in the structure and substructure of tungsten during irradiation by hydrogen plasma flows at the specific energy close to the heat loads on the ITER surface
The changes in the structure, the substructure, and the state of stress in the surface layers of tungsten targets and the cracking processes in them are studied in model experiments on irradiation by a hydrogen plasma in a quasi-stationary plasma accelerator QSPA Kh-50, which adequately reproduces the energy density and the edge localized mode (ELM) time in ITER. The plasma heat load is up to 1 MJ m−2, the pulse duration is 0.25 ms, and the maximum number of irradiating pulses of 150. The development of residual macrostresses from compression to tension is analyzed by X-ray diffraction, and their relation to cracking is shown. Irradiation is found to increase the lattice parameter of tungsten in the undeformable section from a 0 ≈ 0.31642 ± 0.00001 (initial state) to 0.31645 ± 0.00001 nm. The changes in the coherent scattering region and microstrains are estimated. The role of point defects and their complexes in the irradiation-assisted processes is established. A qualitative model is proposed to explain these changes.
- 1 May 2014
- Published by IOP Publishing in Physica Scripta
- Vol. T161
Plasma exposure of different tungsten grades with plasma accelerators under ITER-relevant conditions
- 1 May 2014
- Published by IOP Publishing in Physica Scripta
- Vol. T161
Plasma exposure of different tungsten grades with plasma accelerators under ITER-relevant conditions
- 1 April 2014
- Published by IOP Publishing in Physica Scripta
- Vol. T159
Tungsten damage and melt losses under plasma accelerator exposure with ITER ELM relevant conditions
- 1 April 2014
- Published by IOP Publishing in Physica Scripta
- Vol. T159
Tungsten damage and melt losses under plasma accelerator exposure with ITER ELM relevant conditions