Carsten Netzel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Carsten Netzel has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Markus Weyers
Ferdinand-Braun-Institut (FBH)
9 shared publications Arne Knauer
Ferdinand-Braun-Institut gGmbH Leibniz-Institut für Höchstfrequenztechnik Gustav-Kirchhoff-Strasse 4 Berlin 12489 Germany
5 shared publications- Sylvia Hagedorn
Ferdinand‐Braun‐Institut (FBH) Gustav‐Kirchhoff‐Strasse 4 12489 Berlin Germany
4 shared publications Veit Hoffmann
Ferdinand-Braun-Institut, Leibniz-Institut für Höchstfrequenztechnik Gustav-Kirchhoff-Straße 4 12489 Berlin Germany
4 shared publications- Tim Kolbe
Ferdinand-Braun-Institut (FBH) , Gustav-Kirchhoff-Str. 4, 12489 Berlin
3 shared publications - Anna Mogilatenko
Ferdinand-Braun-Institut (FBH)
2 shared publications
Latest Publications
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (23) , 1917-1920
Engineering Mesa Fabrication for Optimized Performance of AlGaN-Based Far-UVC LEDs
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 38 (23) , 1917-1920
Engineering Mesa Fabrication for Optimized Performance of AlGaN-Based Far-UVC LEDs
- Open Access
- 11 November 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (45) , 453001
Selected topics on the reliability of GaAs- and GaN-based laser diodes
Driven by increasingly demanding applications, research into understanding degradation mechanisms and improving the reliability of edge-emitting quantum-well GaAs- and GaN-based laser diodes (LDs) has become an important parameter for advancing these devices. This paper presents an overview of results from aging and reliability studies on GaAs- and GaN-based LDs manufactured at the Ferdinand-Braun-Institute. The results are organized into three main topics: First, semiconductor-related effects, where gradual degradation and sudden failures are analyzed by studying the impact of operating conditions on electro-optical properties, combined with material analysis techniques such as scanning electron microscope, cathodoluminescence, and transmission electron microscope of degraded and failed devices. Second, facet-related degradation, where the impact of facet preparation technologies on LD degradation behavior is examined. Third, a review of statistical methods aimed at predicting the lifetime of these devices through empirical and physics-based modeling approaches.
- 11 November 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (45) , 453001
Open AccessSelected topics on the reliability of GaAs- and GaN-based laser diodes
Driven by increasingly demanding applications, research into understanding degradation mechanisms and improving the reliability of edge-emitting quantum-well GaAs- and GaN-based laser diodes (LDs) has become an important parameter for advancing these devices. This paper presents an overview of results from aging and reliability studies on GaAs- and GaN-based LDs manufactured at the Ferdinand-Braun-Institute. The results are organized into three main topics: First, semiconductor-related effects, where gradual degradation and sudden failures are analyzed by studying the impact of operating conditions on electro-optical properties, combined with material analysis techniques such as scanning electron microscope, cathodoluminescence, and transmission electron microscope of degraded and failed devices. Second, facet-related degradation, where the impact of facet preparation technologies on LD degradation behavior is examined. Third, a review of statistical methods aimed at predicting the lifetime of these devices through empirical and physics-based modeling approaches.
- Open Access
- 8 July 2026
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (14)
Influence of Backside Surface and Subsurface Damage in Gallium Nitride Wafers on Facet Quality and Violet‐Emitting Laser Diode Performance
Backside wafer thinning is crucial for producing high‐performance GaN laser, as it enables precise cleavage and the formation of high‐quality facets. This study investigates the effects of thinning techniques—lapping with different abrasive sizes, grinding, and mechanical polishing—on surface and subsurface damage (SSD) in GaN wafers, and examines how backside properties influence cleaved facets and device performance. Compared to lapping, grinding produces lower surface roughness, reduces SSD by up to a factor of five to 0.7 µm, and increases the wafer's bow radius by up to a factor of two to 0.65 m. Subsequent mechanical polishing yields a smoother surface, eliminates SSD, and further increases the bow radius to 2.2 m. The improved surface reduces the risk of unintentional wafer breakage from thinning‐induced damage, stress, and tensile strain in epitaxial layers. X‐ray diffraction confirms enhanced crystallinity with polished surfaces and finer abrasives. A clear correlation emerges between SSD, terrace formation on laser facets, and device performance. Lapping produces the roughest facets and the highest, most scattered threshold currents, while grinding and polishing yield smoother facets and reduce threshold current by nearly 40%. These findings highlight the critical role of backside surface quality in fabricating reliable, high‐performance GaN lasers.
- 8 July 2026
- Published by Wiley in Physica Status Solidi (a)
- Vol. 223 (14)
Open AccessInfluence of Backside Surface and Subsurface Damage in Gallium Nitride Wafers on Facet Quality and Violet‐Emitting Laser Diode Performance
Backside wafer thinning is crucial for producing high‐performance GaN laser, as it enables precise cleavage and the formation of high‐quality facets. This study investigates the effects of thinning techniques—lapping with different abrasive sizes, grinding, and mechanical polishing—on surface and subsurface damage (SSD) in GaN wafers, and examines how backside properties influence cleaved facets and device performance. Compared to lapping, grinding produces lower surface roughness, reduces SSD by up to a factor of five to 0.7 µm, and increases the wafer's bow radius by up to a factor of two to 0.65 m. Subsequent mechanical polishing yields a smoother surface, eliminates SSD, and further increases the bow radius to 2.2 m. The improved surface reduces the risk of unintentional wafer breakage from thinning‐induced damage, stress, and tensile strain in epitaxial layers. X‐ray diffraction confirms enhanced crystallinity with polished surfaces and finer abrasives. A clear correlation emerges between SSD, terrace formation on laser facets, and device performance. Lapping produces the roughest facets and the highest, most scattered threshold currents, while grinding and polishing yield smoother facets and reduce threshold current by nearly 40%. These findings highlight the critical role of backside surface quality in fabricating reliable, high‐performance GaN lasers.
- 1 May 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (17)
Temperature dependence of charge carrier diffusion in GaN and AlGaN layers
The development of ultraviolet AlGaN-based LEDs and laser diodes focuses on efficiency and lifetime. Efficient light generation and the reduction of nonradiative losses in the active layers are key factors in this optimization. However, recombination in AlGaN is a complex interplay of various factors: carrier localization due to local bandgap fluctuations, high defect densities, strong exciton binding, composition- and strain-dependent switching of the valence band ordering, as well as spontaneous and piezoelectric polarization fields in heterostructures. The diffusion of charge carriers determines the probability that they will reach nonradiative recombination centers in the material and thus become lost for light generation. We have compared the temperature-dependent charge carrier diffusion in GaN and AlxGa1−xN (x ≈ 0.5) layers using photoluminescence and cathodoluminescence measurements. Under conditions of low excitation power, the diffusion length in AlGaN is significantly shorter than 200 nm due to compositional and bandgap fluctuations. It is at least 2 times shorter than in homogeneous GaN. In addition, the diffusion length in GaN decreases from cryogenic temperatures to room temperature, which is typical for a homogeneous semiconductor. Regarding AlGaN, carrier diffusion increases in the same temperature range. The thermal activation of carrier diffusion in the presence of strong bandgap fluctuations seems to be more important in AlGaN layers than diffusion-limiting effects like phonon scattering and shorter effective recombination times at higher temperatures. This behavior contributes to a steep decrease in light-generation efficiency in AlGaN layers around room temperature, which is not similarly present in GaN layers.
- 1 May 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (17)
Temperature dependence of charge carrier diffusion in GaN and AlGaN layers
The development of ultraviolet AlGaN-based LEDs and laser diodes focuses on efficiency and lifetime. Efficient light generation and the reduction of nonradiative losses in the active layers are key factors in this optimization. However, recombination in AlGaN is a complex interplay of various factors: carrier localization due to local bandgap fluctuations, high defect densities, strong exciton binding, composition- and strain-dependent switching of the valence band ordering, as well as spontaneous and piezoelectric polarization fields in heterostructures. The diffusion of charge carriers determines the probability that they will reach nonradiative recombination centers in the material and thus become lost for light generation. We have compared the temperature-dependent charge carrier diffusion in GaN and AlxGa1−xN (x ≈ 0.5) layers using photoluminescence and cathodoluminescence measurements. Under conditions of low excitation power, the diffusion length in AlGaN is significantly shorter than 200 nm due to compositional and bandgap fluctuations. It is at least 2 times shorter than in homogeneous GaN. In addition, the diffusion length in GaN decreases from cryogenic temperatures to room temperature, which is typical for a homogeneous semiconductor. Regarding AlGaN, carrier diffusion increases in the same temperature range. The thermal activation of carrier diffusion in the presence of strong bandgap fluctuations seems to be more important in AlGaN layers than diffusion-limiting effects like phonon scattering and shorter effective recombination times at higher temperatures. This behavior contributes to a steep decrease in light-generation efficiency in AlGaN layers around room temperature, which is not similarly present in GaN layers.
- Open Access
- 10 November 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (19)
Broadband light emission from GaAsP and GaInP islands grown on silicon nanotip wafer via nanoheteroepitaxy
We present the monolithic integration of GaAsxP1−x and GaxIn1−xP islands, selectively grown on a Si(001) nanotip wafer using gas-source molecular-beam epitaxy via a nanoheteroepitaxy approach. Optimal growth temperatures balancing selectivity and compositional control are 520–580 °C for GaAsP and 500–510 °C for GaInP. By adjusting the group III and V fluxes, island luminescence is tuned across a broad spectral range from 1.5 to 2.1 eV. High-resolution x-ray diffraction measurements on ensembles exceeding one million islands confirm that both GaAsP and GaInP islands are relaxed, while broad diffraction linewidths point to alloy fluctuations. Scanning transmission electron microscopy combined with energy-dispersive x-ray spectroscopy reveals compositional variations of up to 6% among the GaAsP islands, with nearly uniform composition within individual islands. In the case of GaInP, indium-rich regions are observed within single islands, with up to 11% variation across the ensemble. These compositional variations result in broadened or multiple luminescence peaks. Despite challenges in achieving full uniformity, this work demonstrates an alternative pathway for the monolithic integration of scalable III–V infrared-to-visible light emitters and detectors on silicon, advancing the development of microscale light sources for the silicon platform.
- 10 November 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (19)
Open AccessBroadband light emission from GaAsP and GaInP islands grown on silicon nanotip wafer via nanoheteroepitaxy
We present the monolithic integration of GaAsxP1−x and GaxIn1−xP islands, selectively grown on a Si(001) nanotip wafer using gas-source molecular-beam epitaxy via a nanoheteroepitaxy approach. Optimal growth temperatures balancing selectivity and compositional control are 520–580 °C for GaAsP and 500–510 °C for GaInP. By adjusting the group III and V fluxes, island luminescence is tuned across a broad spectral range from 1.5 to 2.1 eV. High-resolution x-ray diffraction measurements on ensembles exceeding one million islands confirm that both GaAsP and GaInP islands are relaxed, while broad diffraction linewidths point to alloy fluctuations. Scanning transmission electron microscopy combined with energy-dispersive x-ray spectroscopy reveals compositional variations of up to 6% among the GaAsP islands, with nearly uniform composition within individual islands. In the case of GaInP, indium-rich regions are observed within single islands, with up to 11% variation across the ensemble. These compositional variations result in broadened or multiple luminescence peaks. Despite challenges in achieving full uniformity, this work demonstrates an alternative pathway for the monolithic integration of scalable III–V infrared-to-visible light emitters and detectors on silicon, advancing the development of microscale light sources for the silicon platform.
- Open Access
- 6 June 2024
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 39 (7) , 075014
Spatial correlation of defect-selective etching and dark luminescence spots in Al x Ga1−x N
Defect-selective etching with molten Ba(OH)2/MgO etch drops was performed on c-plane AlGaN layers covering the entire composition range between GaN and AlN. Regardless of the aluminum content, the etchant produced shallow, hexagonal etch pits with depth-to-diameter ratios of 1/10–1/100. Two predominant types of etch pits were observed, which differed in size. In addition, the etch rate decreased from the center to the edge of the area exposed to the etch drops, providing a radially symmetric variation in etch pit size. For all AlGaN compositions, the positions of the etch pits correlate perfectly with the positions of the dark luminescence spots in cathodoluminescence measurements. Areas on the AlGaN samples that were not exposed to the etching procedure showed identical dark spots with the same size and density as those in the etched regions. Additionally, the density of etch pits and dark spots corresponded to the density of threading dislocations in the AlGaN layers. These observations demonstrate that the density of threading dislocations in c-plane AlGaN layers can be determined by destructive defect-selective etching with Ba(OH)2/MgO and etch pit counting, as well as by nondestructive counting of the dark spots in cathodoluminescence images.
- 6 June 2024
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 39 (7) , 075014
Open AccessSpatial correlation of defect-selective etching and dark luminescence spots in Al x Ga1−x N
Defect-selective etching with molten Ba(OH)2/MgO etch drops was performed on c-plane AlGaN layers covering the entire composition range between GaN and AlN. Regardless of the aluminum content, the etchant produced shallow, hexagonal etch pits with depth-to-diameter ratios of 1/10–1/100. Two predominant types of etch pits were observed, which differed in size. In addition, the etch rate decreased from the center to the edge of the area exposed to the etch drops, providing a radially symmetric variation in etch pit size. For all AlGaN compositions, the positions of the etch pits correlate perfectly with the positions of the dark luminescence spots in cathodoluminescence measurements. Areas on the AlGaN samples that were not exposed to the etching procedure showed identical dark spots with the same size and density as those in the etched regions. Additionally, the density of etch pits and dark spots corresponded to the density of threading dislocations in the AlGaN layers. These observations demonstrate that the density of threading dislocations in c-plane AlGaN layers can be determined by destructive defect-selective etching with Ba(OH)2/MgO and etch pit counting, as well as by nondestructive counting of the dark spots in cathodoluminescence images.
- Open Access
- 5 February 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (6)
Origin of the parasitic luminescence of 235 nm UVC LEDs grown on different AlN templates
AlN layers annealed at high temperatures offer low threading dislocation densities of mid 108 cm−2 and are therefore increasingly used as base layers in ultraviolet (UV) light emitting diode (LED) heterostructure growth. These LEDs, just like those grown on conventional metalorganic vapor phase epitaxy (MOVPE) AlN templates, often suffer from long-wavelength parasitic luminescence. In this work, luminescence properties of far-UVC LED heterostructures grown on MOVPE-AlN/sapphire templates and high-temperature annealed AlN/sapphire templates are compared. To investigate the origin of parasitic emission with high spatial resolution, cross section scanning transmission electron microscopy was combined with cathodoluminescence measurements. As a result, the main origin of the parasitic luminescence band centered at 3.5 eV (354 nm) for the heterostructure grown on annealed AlN is assigned to point defects related to oxygen in the AlN template layer. The defect band centered at 3.0 eV (413 nm) for the heterostructure grown on MOVPE-AlN was found to be related to self-compensating VAl-Si point defect complexes in the n-AlGaN layer and oxygen incorporation close to the AlN/sapphire interface. The results also suggest that the type of AlN template determines the kind of parasitic luminescence from the n-AlGaN layer.
- 5 February 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (6)
Open AccessOrigin of the parasitic luminescence of 235 nm UVC LEDs grown on different AlN templates
AlN layers annealed at high temperatures offer low threading dislocation densities of mid 108 cm−2 and are therefore increasingly used as base layers in ultraviolet (UV) light emitting diode (LED) heterostructure growth. These LEDs, just like those grown on conventional metalorganic vapor phase epitaxy (MOVPE) AlN templates, often suffer from long-wavelength parasitic luminescence. In this work, luminescence properties of far-UVC LED heterostructures grown on MOVPE-AlN/sapphire templates and high-temperature annealed AlN/sapphire templates are compared. To investigate the origin of parasitic emission with high spatial resolution, cross section scanning transmission electron microscopy was combined with cathodoluminescence measurements. As a result, the main origin of the parasitic luminescence band centered at 3.5 eV (354 nm) for the heterostructure grown on annealed AlN is assigned to point defects related to oxygen in the AlN template layer. The defect band centered at 3.0 eV (413 nm) for the heterostructure grown on MOVPE-AlN was found to be related to self-compensating VAl-Si point defect complexes in the n-AlGaN layer and oxygen incorporation close to the AlN/sapphire interface. The results also suggest that the type of AlN template determines the kind of parasitic luminescence from the n-AlGaN layer.
- Open Access
- 26 January 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (4) , 045702
Impact of Si doping on dislocation behavior in MOVPE-grown AlN on high-temperature annealed AlN buffer layers
In this work, we compare the defect structure in unintentionally doped and Si-doped AlN layers grown by metalorganic vapor phase epitaxy (MOVPE) on high-temperature annealed (HTA) sputtered AlN templates on sapphire substrates. Since the HTA process leads to a reduction of the in-plane lattice constant of the AlN layers, further homoepitaxial overgrowth results in compressively strained AlN layers. With increasing MOVPE-AlN layer thickness, strain relaxation takes place mostly by formation of dislocation half-loops of an irregular shape, which accumulate at the homoepitaxial MOVPE-AlN/HTA-AlN interface. We suggest that these dislocations nucleate at the layer surface and move down to the homoepitaxial interface at high temperatures. The formation of these irregular and hardly controllable defects can be avoided by introduction of Si-doping into the MOVPE-AlN layers. Si-doping enlarges the inclination of threading dislocation lines stemming from the HTA-AlN template, producing an alternative mechanism for strain relaxation.
- 26 January 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (4) , 045702
Open AccessImpact of Si doping on dislocation behavior in MOVPE-grown AlN on high-temperature annealed AlN buffer layers
In this work, we compare the defect structure in unintentionally doped and Si-doped AlN layers grown by metalorganic vapor phase epitaxy (MOVPE) on high-temperature annealed (HTA) sputtered AlN templates on sapphire substrates. Since the HTA process leads to a reduction of the in-plane lattice constant of the AlN layers, further homoepitaxial overgrowth results in compressively strained AlN layers. With increasing MOVPE-AlN layer thickness, strain relaxation takes place mostly by formation of dislocation half-loops of an irregular shape, which accumulate at the homoepitaxial MOVPE-AlN/HTA-AlN interface. We suggest that these dislocations nucleate at the layer surface and move down to the homoepitaxial interface at high temperatures. The formation of these irregular and hardly controllable defects can be avoided by introduction of Si-doping into the MOVPE-AlN layers. Si-doping enlarges the inclination of threading dislocation lines stemming from the HTA-AlN template, producing an alternative mechanism for strain relaxation.
- Open Access
- 24 August 2021
- Published by Wiley in Physica Status Solidi (b)
- Vol. 258 (11)
Temperature Dependence of Dark Spot Diameters in GaN and AlGaN
Threading dislocations in c‐plane (Al,Ga)N layers are surrounded by areas with reduced light generation efficiency, called “dark spots.” These areas are observable in luminescence measurements with spatial resolution in the submicrometer range. Dark spots reduce the internal quantum efficiency in single layers and light‐emitting devices. In cathodoluminescence measurements, the diameter of dark spots (full width at half maximum [FWHM]) is observed to be 200–250 nm for GaN. It decreases by 30–60% for AlxGa1−xN with x ≈ 0.5. Furthermore, the dark spot diameter increases with increasing temperature from 83 to 300 K in AlGaN, whereas it decreases in GaN. Emission energy mappings around dark spots become less smooth and show sharper features on submicrometer scales at low temperature for AlGaN and, on the contrary, at high temperature for GaN. It is concluded that charge carrier localization dominates the temperature dependence of dark spot diameters and of the emission energy distribution around threading dislocations in AlGaN, whereas the temperature‐dependent excitation volume in cathodoluminescence and charge carrier diffusion limited by phonon scattering are the dominant effects in GaN. Consequently, with increasing temperature, nonradiative recombination related to threading dislocations extends to wider regions in AlGaN, whereas it becomes spatially limited in GaN.
- 24 August 2021
- Published by Wiley in Physica Status Solidi (b)
- Vol. 258 (11)
Open AccessTemperature Dependence of Dark Spot Diameters in GaN and AlGaN
Threading dislocations in c‐plane (Al,Ga)N layers are surrounded by areas with reduced light generation efficiency, called “dark spots.” These areas are observable in luminescence measurements with spatial resolution in the submicrometer range. Dark spots reduce the internal quantum efficiency in single layers and light‐emitting devices. In cathodoluminescence measurements, the diameter of dark spots (full width at half maximum [FWHM]) is observed to be 200–250 nm for GaN. It decreases by 30–60% for AlxGa1−xN with x ≈ 0.5. Furthermore, the dark spot diameter increases with increasing temperature from 83 to 300 K in AlGaN, whereas it decreases in GaN. Emission energy mappings around dark spots become less smooth and show sharper features on submicrometer scales at low temperature for AlGaN and, on the contrary, at high temperature for GaN. It is concluded that charge carrier localization dominates the temperature dependence of dark spot diameters and of the emission energy distribution around threading dislocations in AlGaN, whereas the temperature‐dependent excitation volume in cathodoluminescence and charge carrier diffusion limited by phonon scattering are the dominant effects in GaN. Consequently, with increasing temperature, nonradiative recombination related to threading dislocations extends to wider regions in AlGaN, whereas it becomes spatially limited in GaN.
- Open Access
- 14 May 2020
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 49 (9) , 5138-5143
Optimization of the Epitaxial Growth of Undoped GaN Waveguides in GaN-Based Laser Diodes Evaluated by Photoluminescence
Non-intentionally doped c-plane GaN layers are generally employed as p-side waveguide layers in violet/blue-emitting laser diodes. The recombination and diffusion of charge carriers in the p-side GaN waveguide influence the injection efficiency of holes into the InGaN quantum wells of these devices. In this study, the non-radiative recombination and the diffusivity in the [000-1] direction for charge carriers in such GaN layers are investigated by the photoluminescence of buried InGaN quantum wells, in addition to the GaN photoluminescence. The vertical charge carrier diffusion length and the diffusion constant in GaN were determined by evaluating the intensity from InGaN quantum wells in different depths below a top GaN layer. Additionally, the intensity from the buried InGaN quantum wells was found to be more sensitive to variations in the non-radiative recombination rate in the GaN layer than the intensity from the GaN itself. The study enables conclusions to be drawn on how the growth of a p-side GaN waveguide layer has to be optimized: (1) The charge carrier diffusivity in the [000-1] direction at device operation temperature is limited by phonon scattering and can be only slightly improved by material quality. (2) The use of TMGa (trimethylgallium) instead of TEGa (triethylgallium) as a precursor for the growth of GaN lowers the background silicon doping level and is advantageous for a large hole diffusion length. (3) Small growth rates below 0.5 μm/h when using TMGa or below 0.12 μm/h when using TEGa enhance non-radiative recombination. (4) A V/III gas ratio of 2200 or more is needed for low non-radiative recombination rates in GaN.
- 14 May 2020
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 49 (9) , 5138-5143
Open AccessOptimization of the Epitaxial Growth of Undoped GaN Waveguides in GaN-Based Laser Diodes Evaluated by Photoluminescence
Non-intentionally doped c-plane GaN layers are generally employed as p-side waveguide layers in violet/blue-emitting laser diodes. The recombination and diffusion of charge carriers in the p-side GaN waveguide influence the injection efficiency of holes into the InGaN quantum wells of these devices. In this study, the non-radiative recombination and the diffusivity in the [000-1] direction for charge carriers in such GaN layers are investigated by the photoluminescence of buried InGaN quantum wells, in addition to the GaN photoluminescence. The vertical charge carrier diffusion length and the diffusion constant in GaN were determined by evaluating the intensity from InGaN quantum wells in different depths below a top GaN layer. Additionally, the intensity from the buried InGaN quantum wells was found to be more sensitive to variations in the non-radiative recombination rate in the GaN layer than the intensity from the GaN itself. The study enables conclusions to be drawn on how the growth of a p-side GaN waveguide layer has to be optimized: (1) The charge carrier diffusivity in the [000-1] direction at device operation temperature is limited by phonon scattering and can be only slightly improved by material quality. (2) The use of TMGa (trimethylgallium) instead of TEGa (triethylgallium) as a precursor for the growth of GaN lowers the background silicon doping level and is advantageous for a large hole diffusion length. (3) Small growth rates below 0.5 μm/h when using TMGa or below 0.12 μm/h when using TEGa enhance non-radiative recombination. (4) A V/III gas ratio of 2200 or more is needed for low non-radiative recombination rates in GaN.