Ieda Lúcia Viana Rosa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ieda Lúcia Viana Rosa has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Elson Longo
Federal University of Sao Carlos (UFSCar)
5 shared publications Edson R. Leite
UFSCar
4 shared publicationsJosé A. Varela
UNESP
3 shared publications- Ana Paula Azevedo Marques
UNIFESP Univ Fed Sao Paulo, Rua Prof Artur Riedel,275, Diadema, SP, Brazil
2 shared publications Marcos T. S. Tanaka
UFSCar
2 shared publicationsA. S. B. Sombra
Federal University of Ceará, Campus do Pici
1 shared publication
Latest Publications
- 11 November 2008
- Published by Springer Nature in Journal of Fluorescence
- Vol. 19 (3) , 495-500
Europium(III) Concentration Effect on the Spectroscopic and Photoluminescent Properties of BaMoO4:Eu
BaMoO4:Eu (BEMO) powders were synthesized by the polymeric precursor method (PPM), heat treated at 800 °C for 2 h in a heating rate of 5 °C/min and characterized by powder X-ray diffraction patterns (XRD), Fourier Transform Infra-Red (FTIR) and Raman spectroscopy, besides room temperature Photoluminescence (PL) measurements. The emission spectra of BEMO samples under excitation of 394 nm present the characteristic Eu3+ transitions. The relative intensities of the Eu3+ emissions increase as the concentration of this ion increases from 0.01 to 0.075 mol, but the luminescence is drastically quenched for the Ba0.855Eu0.145MoO4 sample. The one exponential decay curves of the Eu3+ 5D0→7F2 transition, λ exc = 394 nm and λ em = 614 nm, provided the decay times of around 0.54 ms for all samples. It was observed a broadening of the Bragg reflections and Raman bands when the Eu+3 concentration increases as a consequence of a more disordered material. The presence of MoO3 and Eu2Mo2O7 as additional phases in the BEMO samples where observed when the Eu3+ concentration was 14.5 mol%.
- 11 November 2008
- Published by Springer Nature in Journal of Fluorescence
- Vol. 19 (3) , 495-500
Europium(III) Concentration Effect on the Spectroscopic and Photoluminescent Properties of BaMoO4:Eu
BaMoO4:Eu (BEMO) powders were synthesized by the polymeric precursor method (PPM), heat treated at 800 °C for 2 h in a heating rate of 5 °C/min and characterized by powder X-ray diffraction patterns (XRD), Fourier Transform Infra-Red (FTIR) and Raman spectroscopy, besides room temperature Photoluminescence (PL) measurements. The emission spectra of BEMO samples under excitation of 394 nm present the characteristic Eu3+ transitions. The relative intensities of the Eu3+ emissions increase as the concentration of this ion increases from 0.01 to 0.075 mol, but the luminescence is drastically quenched for the Ba0.855Eu0.145MoO4 sample. The one exponential decay curves of the Eu3+ 5D0→7F2 transition, λ exc = 394 nm and λ em = 614 nm, provided the decay times of around 0.54 ms for all samples. It was observed a broadening of the Bragg reflections and Raman bands when the Eu+3 concentration increases as a consequence of a more disordered material. The presence of MoO3 and Eu2Mo2O7 as additional phases in the BEMO samples where observed when the Eu3+ concentration was 14.5 mol%.
- 5 January 2008
- Published by Springer Nature in Journal of Fluorescence
- Vol. 18 (2) , 541-545
SiO2–GeO2 Soot Preform as a Core for Eu2O3 Nanocoating: Synthesis and Photophysical Study
Nowadays solid state chemists have the possibility of work with low temperature strategies to obtain solid state materials with appropriate physical and chemical properties for useful technological applications. Photonic core shell materials having a core and shell domains composed by a variety of compounds have been synthesized by different methods. In this work we used silica-germania soot prepared by vapor-phase axial deposition as a core where a nanoshell of Eu2O3 was deposited. A new sol-gel like method was used to obtain the Eu2O3 nanoshell coating the SiO2–GeO2 particles, which was prepared by the polymeric precursor method. The photophysical properties of Eu3+ were used to obtain information about the rare earth surrounding in the SiO2–GeO2@Eu2O3 material during the sintering process. The sintering process was followed by the luminescence spectra of Eu3+ and all the samples present the characteristic emission related to the 5D0→7F J (J = 0, 1, 2, 3 and 4). The ratios of the 5D0→7F2/5D0→7F1 emission intensity for the SiO2–GeO2@Eu2O3 systems were calculated and it was observed an increase in its values, indicating a low symmetry around the Eu3+ as the temperature increases.
- 5 January 2008
- Published by Springer Nature in Journal of Fluorescence
- Vol. 18 (2) , 541-545
SiO2–GeO2 Soot Preform as a Core for Eu2O3 Nanocoating: Synthesis and Photophysical Study
Nowadays solid state chemists have the possibility of work with low temperature strategies to obtain solid state materials with appropriate physical and chemical properties for useful technological applications. Photonic core shell materials having a core and shell domains composed by a variety of compounds have been synthesized by different methods. In this work we used silica-germania soot prepared by vapor-phase axial deposition as a core where a nanoshell of Eu2O3 was deposited. A new sol-gel like method was used to obtain the Eu2O3 nanoshell coating the SiO2–GeO2 particles, which was prepared by the polymeric precursor method. The photophysical properties of Eu3+ were used to obtain information about the rare earth surrounding in the SiO2–GeO2@Eu2O3 material during the sintering process. The sintering process was followed by the luminescence spectra of Eu3+ and all the samples present the characteristic emission related to the 5D0→7F J (J = 0, 1, 2, 3 and 4). The ratios of the 5D0→7F2/5D0→7F1 emission intensity for the SiO2–GeO2@Eu2O3 systems were calculated and it was observed an increase in its values, indicating a low symmetry around the Eu3+ as the temperature increases.
- 20 December 2007
- Published by Springer Nature in Journal of Fluorescence
- Vol. 18 (2) , 239-245
Synthesis, Characterization and Photophysical Properties of Eu3+ Doped in BaMoO4
In this work Ba0.99Eu0.01MoO4 (BEMO) powders were prepared by the first time by the Complex Polymerization Method. The structural and optical properties of the BEMO powders were characterized by Fourier Transform Infra-Red (FTIR), X-ray Diffraction (XRD), Raman Spectra, High-Resolution Scanning Electron Microscopy (HR-SEM) and Photoluminescent Measurements. XRD show a crystalline scheelite-type phase after the heat treatment at temperatures greater than 400 °C. The ionic radius of Eu3+ (0.109 nm) is lower than the Ba2+ (0.149 nm) one. This difference is responsible for the decrease in the lattice parameters of the BEMO compared to the pure BaMoO4 matrix. This little difference in the lattice parameters show that Eu3+ is expected to occupy the Ba2+ site at different temperatures, stayed the tetragonal (S4) symmetry characteristic of scheelite-type crystalline structures of BaMoO4. The emission spectra of the samples, when excited at 394 nm, presented the 5D1→7F0, 1 and 2 and 5D0→7F0, 1, 2, 3 and 4 Eu3+ transitions at 523, 533, 554, 578, 589, 614, 652 and 699 nm, respectively. The emission spectra of the powders heat-treated at 800 and 900 °C showed a marked increase in its intensities compared to the materials heat-treated from 400 to 700 °C. The decay times for the sample were evaluated and all of them presented the average value of 0.61 ms. Eu3+ luminescence decay time follows one exponential curve indicating the presence of only one type of Eu3+ symmetry site.
- 20 December 2007
- Published by Springer Nature in Journal of Fluorescence
- Vol. 18 (2) , 239-245
Synthesis, Characterization and Photophysical Properties of Eu3+ Doped in BaMoO4
In this work Ba0.99Eu0.01MoO4 (BEMO) powders were prepared by the first time by the Complex Polymerization Method. The structural and optical properties of the BEMO powders were characterized by Fourier Transform Infra-Red (FTIR), X-ray Diffraction (XRD), Raman Spectra, High-Resolution Scanning Electron Microscopy (HR-SEM) and Photoluminescent Measurements. XRD show a crystalline scheelite-type phase after the heat treatment at temperatures greater than 400 °C. The ionic radius of Eu3+ (0.109 nm) is lower than the Ba2+ (0.149 nm) one. This difference is responsible for the decrease in the lattice parameters of the BEMO compared to the pure BaMoO4 matrix. This little difference in the lattice parameters show that Eu3+ is expected to occupy the Ba2+ site at different temperatures, stayed the tetragonal (S4) symmetry characteristic of scheelite-type crystalline structures of BaMoO4. The emission spectra of the samples, when excited at 394 nm, presented the 5D1→7F0, 1 and 2 and 5D0→7F0, 1, 2, 3 and 4 Eu3+ transitions at 523, 533, 554, 578, 589, 614, 652 and 699 nm, respectively. The emission spectra of the powders heat-treated at 800 and 900 °C showed a marked increase in its intensities compared to the materials heat-treated from 400 to 700 °C. The decay times for the sample were evaluated and all of them presented the average value of 0.61 ms. Eu3+ luminescence decay time follows one exponential curve indicating the presence of only one type of Eu3+ symmetry site.
- 1 December 2007
- Published by Springer Nature in Journal of Fluorescence
- Vol. 18 (2) , 253-259
Study of Structural and Photoluminescent Properties of Ca8Eu2(PO4)6O2
In this work it is presented for the first time the nanostructured hydroxyapatites doped with 0.5, 1.0 and 2.0 wt% of Eu3+ prepared at room temperature by the mechanical alloying technique. X-ray diffraction powder (XRD), infrared (IR) and Raman scattering spectroscopy, scanning electron microscopy (SEM), microhardness measurements as well as luminescent data of Eu3+ were used to investigate the structural and optical properties of these nanomaterials. The electrical and dielectrical analyses were used with the intention of having a better comprehension about the electromagnetic fields in pure and doped hydroxyapatites.
- 1 December 2007
- Published by Springer Nature in Journal of Fluorescence
- Vol. 18 (2) , 253-259
Study of Structural and Photoluminescent Properties of Ca8Eu2(PO4)6O2
In this work it is presented for the first time the nanostructured hydroxyapatites doped with 0.5, 1.0 and 2.0 wt% of Eu3+ prepared at room temperature by the mechanical alloying technique. X-ray diffraction powder (XRD), infrared (IR) and Raman scattering spectroscopy, scanning electron microscopy (SEM), microhardness measurements as well as luminescent data of Eu3+ were used to investigate the structural and optical properties of these nanomaterials. The electrical and dielectrical analyses were used with the intention of having a better comprehension about the electromagnetic fields in pure and doped hydroxyapatites.
- 1 October 2006
- Published by Elsevier in Materials Research Bulletin
- Vol. 41 (10) , 1791-1797
Synthesis and photoluminescence study of La1.8Eu0.2O3 coating on nanometric α-Al2O3
- 1 October 2006
- Published by Elsevier in Materials Research Bulletin
- Vol. 41 (10) , 1791-1797
Synthesis and photoluminescence study of La1.8Eu0.2O3 coating on nanometric α-Al2O3
- 16 May 2006
- Published by Springer Nature in Journal of Fluorescence
- Vol. 16 (3) , 455-459
Photophysical Properties of New Terbium (III) Organophosphonates
This paper reports on the synthesis, characterization and photophysical properties of the Tb3+ organophosphonates, TbH(O3PR)2, methylphosphonate (R=CH3), ethylphosphonate (R=C2H5), propylphosphonate (R=C3H7), and phenylphosphonate (R=C6H5). The layered Tb3+ organophosphonates were characterized by X-ray diffraction, IR spectroscopy, TG and elemental analysis. The interlayer distances of the Tb3+ organophosphonates evaluated by the X-ray diffractogram were 9.50 Å for TbH(O3PCH3)2, 12.18 Å for TbH(O3PC2H5)2, 14.84 Å for TbH(O3PC3H7)2 and 15.20 Å for TbH(O3PC6H5)2. The Tb3+ luminescence data revealed highly green emissive materials when they were excited at 368 nm, where the characteristic 5D4 → 7F J (J=6, 5, 4 and 3) transitions of Tb3+ were observed at 488, 543, 585 and 619 nm, respectively. The lifetime of the Tb3+ 5D4 → 7F5 transition (λexc=368 nm and λem=543 nm) for the Tb3+ organophosphonates was evaluated from the decay curves, which values were of 2.88, 2.22, 2.14 and 2.59 ms, respectively for TbH(O3PCH3)2, TbH(O3PC2H5)2, TbH(O3PC3H7)2 and TbH(O3PC6H5)2. TG analysis revealed that these materials are thermally highly stable, with no water molecule in their composition, which makes them potential luminophores.
- 16 May 2006
- Published by Springer Nature in Journal of Fluorescence
- Vol. 16 (3) , 455-459
Photophysical Properties of New Terbium (III) Organophosphonates
This paper reports on the synthesis, characterization and photophysical properties of the Tb3+ organophosphonates, TbH(O3PR)2, methylphosphonate (R=CH3), ethylphosphonate (R=C2H5), propylphosphonate (R=C3H7), and phenylphosphonate (R=C6H5). The layered Tb3+ organophosphonates were characterized by X-ray diffraction, IR spectroscopy, TG and elemental analysis. The interlayer distances of the Tb3+ organophosphonates evaluated by the X-ray diffractogram were 9.50 Å for TbH(O3PCH3)2, 12.18 Å for TbH(O3PC2H5)2, 14.84 Å for TbH(O3PC3H7)2 and 15.20 Å for TbH(O3PC6H5)2. The Tb3+ luminescence data revealed highly green emissive materials when they were excited at 368 nm, where the characteristic 5D4 → 7F J (J=6, 5, 4 and 3) transitions of Tb3+ were observed at 488, 543, 585 and 619 nm, respectively. The lifetime of the Tb3+ 5D4 → 7F5 transition (λexc=368 nm and λem=543 nm) for the Tb3+ organophosphonates was evaluated from the decay curves, which values were of 2.88, 2.22, 2.14 and 2.59 ms, respectively for TbH(O3PCH3)2, TbH(O3PC2H5)2, TbH(O3PC3H7)2 and TbH(O3PC6H5)2. TG analysis revealed that these materials are thermally highly stable, with no water molecule in their composition, which makes them potential luminophores.