John S. Dennis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
John S. Dennis has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
A. N. Hayhurst
Dept. of Chemical Engineering, University of Cambridge, Pembroke Street, Cambridge CB2 3RA, U.K.
2 shared publications- A. N. Hayhurst
University of Cambridge
2 shared publications A.C. Rees
2 shared publications- Andrew J. Sederman
Department of Chemical Engineering and Biotechnology, University of Cambridge, West Cambridge Site, Philippa Fawcett Drive, Cambridge CB3 0AS, United Kingdom
2 shared publications C. R. Müller
Dept. of Chemical Engineering, University of Cambridge, Pembroke Street, Cambridge CB2 3RA, U.K.
2 shared publications- Christopher J. Howe
Department of Biochemistry, University of Cambridge, Cambridge, UK
2 shared publications
Latest Publications
- 1 January 2014
- Published by Elsevier in Bioresource Technology
- Vol. 152, 464-470
The purification of crude glycerol derived from biodiesel manufacture and its use as a substrate by Rhodopseudomonas palustris to produce hydrogen
- 1 January 2014
- Published by Elsevier in Bioresource Technology
- Vol. 152, 464-470
The purification of crude glycerol derived from biodiesel manufacture and its use as a substrate by Rhodopseudomonas palustris to produce hydrogen
- 1 January 2013
- Published by Elsevier
Contributor contact details
- 8 December 2012
- Published by Elsevier in Bioresource Technology
- Vol. 130, 725-730
Photofermentation of crude glycerol from biodiesel using Rhodopseudomonas palustris: Comparison with organic acids and the identification of inhibitory compounds
- 8 December 2012
- Published by Elsevier in Bioresource Technology
- Vol. 130, 725-730
Photofermentation of crude glycerol from biodiesel using Rhodopseudomonas palustris: Comparison with organic acids and the identification of inhibitory compounds
- 22 November 2012
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 6 (1) , 288-298
A high performance oxygen storage material for chemical looping processes with CO 2 capture
Chemical looping combustion (CLC) is a novel combustion technology that involves cyclic reduction and oxidation of oxygen storage materials to provide oxygen for the combustion of fuels to CO2 and H2O, whilst giving a pure stream of CO2 suitable for sequestration or utilisation. Here, we report a method for preparing of oxygen storage materials from layered double hydroxides (LDHs) precursors and demonstrate their applications in the CLC process. The LDHs precursor enables homogeneous mixing of elements at the molecular level, giving a high degree of dispersion and high-loading of active metal oxide in the support after calcination. Using a Cu–Al LDH precursor as a prototype, we demonstrate that rational design of oxygen storage materials by material chemistry significantly improved the reactivity and stability in the high temperature redox cycles. We discovered that the presence of sodium-containing species were effective in inhibiting the formation of copper aluminates (CuAl2O4 or CuAlO2) and stabilising the copper phase in an amorphous support over multiple redox cycles. A representative nanostructured Cu-based oxygen storage material derived from the LDH precursor showed stable gaseous O2 release capacity (∼5 wt%), stable oxygen storage capacity (∼12 wt%), and stable reaction rates during reversible phase changes between CuO–Cu2O–Cu at high temperatures (800–1000 °C). We anticipate that the strategy can be extended to manufacture a variety of metal oxide composites for applications in novel high temperature looping cycles for clean energy production and CO2 capture.
- 22 November 2012
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 6 (1) , 288-298
A high performance oxygen storage material for chemical looping processes with CO 2 capture
Chemical looping combustion (CLC) is a novel combustion technology that involves cyclic reduction and oxidation of oxygen storage materials to provide oxygen for the combustion of fuels to CO2 and H2O, whilst giving a pure stream of CO2 suitable for sequestration or utilisation. Here, we report a method for preparing of oxygen storage materials from layered double hydroxides (LDHs) precursors and demonstrate their applications in the CLC process. The LDHs precursor enables homogeneous mixing of elements at the molecular level, giving a high degree of dispersion and high-loading of active metal oxide in the support after calcination. Using a Cu–Al LDH precursor as a prototype, we demonstrate that rational design of oxygen storage materials by material chemistry significantly improved the reactivity and stability in the high temperature redox cycles. We discovered that the presence of sodium-containing species were effective in inhibiting the formation of copper aluminates (CuAl2O4 or CuAlO2) and stabilising the copper phase in an amorphous support over multiple redox cycles. A representative nanostructured Cu-based oxygen storage material derived from the LDH precursor showed stable gaseous O2 release capacity (∼5 wt%), stable oxygen storage capacity (∼12 wt%), and stable reaction rates during reversible phase changes between CuO–Cu2O–Cu at high temperatures (800–1000 °C). We anticipate that the strategy can be extended to manufacture a variety of metal oxide composites for applications in novel high temperature looping cycles for clean energy production and CO2 capture.
- 24 May 2011
- Published by Elsevier in Particuology
- Vol. 9 (4) , 330-341
Multi-scale magnetic resonance measurements and validation of Discrete Element Model simulations
- 24 May 2011
- Published by Elsevier in Particuology
- Vol. 9 (4) , 330-341
Multi-scale magnetic resonance measurements and validation of Discrete Element Model simulations
- 24 October 2008
- Published by Wiley in AIChE Journal
- Vol. 54 (12) , 3308-3311
How does the concentration of CO2 affect its uptake by a synthetic Ca‐based solid sorbent?
- 24 October 2008
- Published by Wiley in AIChE Journal
- Vol. 54 (12) , 3308-3311
How does the concentration of CO2 affect its uptake by a synthetic Ca‐based solid sorbent?
- 29 May 2008
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 86 (3) , 356-366
Synthetic Ca‐based solid sorbents suitable for capturing CO2 in a fluidized bed
Coprecipitation and hydrolysis of CaO have been employed to produce Ca‐based synthetic sorbents suitable for capturing CO2 in a fluidized bed. Their composition, CO2 uptake, volume in small pores (2–200 nm) and resistance to attrition were measured and compared to those of limestone and dolomite. Sorbents produced by hydrolysis showed the highest uptake and resistance to attrition. After 20 cycles of carbonation and calcination, two sorbents exceeded the uptake of both limestone and dolomite, when subjected to the same regimes of reaction. A sorbent's uptake of CO2 was shown to be determined by the volume in pores narrower than ∼200 nm.
- 29 May 2008
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 86 (3) , 356-366
Synthetic Ca‐based solid sorbents suitable for capturing CO2 in a fluidized bed
Coprecipitation and hydrolysis of CaO have been employed to produce Ca‐based synthetic sorbents suitable for capturing CO2 in a fluidized bed. Their composition, CO2 uptake, volume in small pores (2–200 nm) and resistance to attrition were measured and compared to those of limestone and dolomite. Sorbents produced by hydrolysis showed the highest uptake and resistance to attrition. After 20 cycles of carbonation and calcination, two sorbents exceeded the uptake of both limestone and dolomite, when subjected to the same regimes of reaction. A sorbent's uptake of CO2 was shown to be determined by the volume in pores narrower than ∼200 nm.
- 1 June 2007
- Published by Taylor & Francis in Journal of the Energy Institute
- Vol. 80 (2) , 65-72
Reaction between calcium oxide and hydrogen sulphide and also its modelling for a fluidised bed coal gasifier
The reaction of solid particles of CaO with gaseous H2S in CaO+H2S→CaS+H2O has been studied in a hot, laboratory scale, fluidised bed. The reaction displays Langmuir–Hinshelwood kinetics, being zeroth order in H2S with large concentrations of H2S, but first order for tiny concentrations (≪ 10−4 mol m−3 at 950°C) of H2S; the first order rate constant was measured in a fluidised bed. An important and significant difference is found between the first order rate coefficients measured in a fluidised bed and in a thermogravimetric experiment. Two mathematical models for removing H2S by, for example, adding CaO to a coal gasifier are formulated, one with Langmuir–Hinshelwood kinetics, the other, an asymptotic model, with simplified first order kinetics. Both describe the experimental facts fairly well; interestingly, the simplified model works unexpectedly well for the sulphidation of CaO particles bigger than 0·5 mm, even at pressures up to 18 bar. A match between experiments and modelling succeeds in yielding values for the rate constant of reaction (1), the effective diffusion coefficient of H2S through the product CaS, the initial porosity of the particles of CaO and the initial effective diffusivity of H2S through porous CaO. The simpler model is slightly inaccurate for the initial stages of sulphidation of realistically sized particles (diameter≈0·5 mm) of CaO in a gasifier. This is because sulphidation is initially confined to the exterior of a particle and is actually zeroth order for the conditions of a gasifier. However, towards the end of reaction (1), the asymptotic model describes the observations well because in the centre of realistically sized particles of CaO, first order kinetics are eventually obeyed.
- 1 June 2007
- Published by Taylor & Francis in Journal of the Energy Institute
- Vol. 80 (2) , 65-72
Reaction between calcium oxide and hydrogen sulphide and also its modelling for a fluidised bed coal gasifier
The reaction of solid particles of CaO with gaseous H2S in CaO+H2S→CaS+H2O has been studied in a hot, laboratory scale, fluidised bed. The reaction displays Langmuir–Hinshelwood kinetics, being zeroth order in H2S with large concentrations of H2S, but first order for tiny concentrations (≪ 10−4 mol m−3 at 950°C) of H2S; the first order rate constant was measured in a fluidised bed. An important and significant difference is found between the first order rate coefficients measured in a fluidised bed and in a thermogravimetric experiment. Two mathematical models for removing H2S by, for example, adding CaO to a coal gasifier are formulated, one with Langmuir–Hinshelwood kinetics, the other, an asymptotic model, with simplified first order kinetics. Both describe the experimental facts fairly well; interestingly, the simplified model works unexpectedly well for the sulphidation of CaO particles bigger than 0·5 mm, even at pressures up to 18 bar. A match between experiments and modelling succeeds in yielding values for the rate constant of reaction (1), the effective diffusion coefficient of H2S through the product CaS, the initial porosity of the particles of CaO and the initial effective diffusivity of H2S through porous CaO. The simpler model is slightly inaccurate for the initial stages of sulphidation of realistically sized particles (diameter≈0·5 mm) of CaO in a gasifier. This is because sulphidation is initially confined to the exterior of a particle and is actually zeroth order for the conditions of a gasifier. However, towards the end of reaction (1), the asymptotic model describes the observations well because in the centre of realistically sized particles of CaO, first order kinetics are eventually obeyed.
- 1 January 2007
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 85 (10) , 1341-1347
The Apparent Viscosity of the Particulate Phase of Bubbling Gas-Fluidized Beds
- 1 January 2007
- Published by Elsevier in Chemical Engineering Research and Design
- Vol. 85 (10) , 1341-1347
The Apparent Viscosity of the Particulate Phase of Bubbling Gas-Fluidized Beds
- 15 September 2006
- Published by Elsevier in Chemical Engineering Science
- Vol. 62 (1-2) , 82-93
Rise velocities of bubbles and slugs in gas-fluidised beds: Ultra-fast magnetic resonance imaging
- 15 September 2006
- Published by Elsevier in Chemical Engineering Science
- Vol. 62 (1-2) , 82-93
Rise velocities of bubbles and slugs in gas-fluidised beds: Ultra-fast magnetic resonance imaging