S. Kleiner
Research Subjects
S. Kleiner has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
O. Beffort
Laboratory for Materials Technology Thun, Empa Materials Science and Technology, Feuerwerkerstrasse 39, CH-3602 Thun, Switzerland
2 shared publicationsE. Ogris
Institute of Metallurgy, ETH Swiss Federal Institute of Technology, CH‐8092 Zürich, Switzerland
1 shared publicationF. A. Khalid
Laboratory for Materials Technology Thun, Empa Materials Science and Technology, Feuerwerkerstrasse 39, CH-3602 Thun, Switzerland
1 shared publicationF. Bertocco
Laboratory for Materials Technology Thun, Empa Materials Science and Technology, Feuerwerkerstrasse 39, CH-3602 Thun, Switzerland
1 shared publication- Peter J. Uggowitzer
Department of Metallurgy, Chair of Non‐Ferrous Metallurgy Montanuniversität Leoben Franz‐Josef‐Strasse 18 8700 Leoben Austria
1 shared publication
Latest Publications
- 31 May 2005
- Published by Wiley in Advanced Engineering Materials
- Vol. 7 (5) , 380-383
Reactively Synthesized Nanostructured PM Aluminium Composite – Microstructure Stability and Elevated Temperature Hardness Response
Reactive synthesis by mechanical alloying and subsequent hot consolidation is an appropriate way to produce an Al‐Al3Ti‐Al2O3 nanocomposite from readily available and inexpensive aluminium powder and nanosized TiO2. This processing route provides a fine grained and thermally stable microstructure with a controllable amount of dispersoids. The respective material shows a high hardness at room and elevated temperature and does not suffer from softening during long‐term annealing at 250°C. It is therefore considered to be a promising light‐weight material for elevated temperature applications.
- 31 May 2005
- Published by Wiley in Advanced Engineering Materials
- Vol. 7 (5) , 380-383
Reactively Synthesized Nanostructured PM Aluminium Composite – Microstructure Stability and Elevated Temperature Hardness Response
Reactive synthesis by mechanical alloying and subsequent hot consolidation is an appropriate way to produce an Al‐Al3Ti‐Al2O3 nanocomposite from readily available and inexpensive aluminium powder and nanosized TiO2. This processing route provides a fine grained and thermally stable microstructure with a controllable amount of dispersoids. The respective material shows a high hardness at room and elevated temperature and does not suffer from softening during long‐term annealing at 250°C. It is therefore considered to be a promising light‐weight material for elevated temperature applications.
- 8 September 2003
- Published by Wiley in Advanced Engineering Materials
- Vol. 5 (9) , 653-658
Semi‐Solid Metal Processing of Aluminum Alloy A356 and Magnesium Alloy AZ91: Comparison Based on Metallurgical Consideration
Thixocasting or rheocasting of AZ and AM magnesium alloys continues to be a problematic case in semi‐solid processing. The comparison with the aluminum thixo alloy A 356 shows that the metallurgical and physical properties of the Mg alloy AZ 91 are little compatible with this technology (see Figure for the morphology of the eutectic in AZ 91): The conclusions from this study are of fundamental importance for future developments in this field of research.
- 8 September 2003
- Published by Wiley in Advanced Engineering Materials
- Vol. 5 (9) , 653-658
Semi‐Solid Metal Processing of Aluminum Alloy A356 and Magnesium Alloy AZ91: Comparison Based on Metallurgical Consideration
Thixocasting or rheocasting of AZ and AM magnesium alloys continues to be a problematic case in semi‐solid processing. The comparison with the aluminum thixo alloy A 356 shows that the metallurgical and physical properties of the Mg alloy AZ 91 are little compatible with this technology (see Figure for the morphology of the eutectic in AZ 91): The conclusions from this study are of fundamental importance for future developments in this field of research.