Mustafa Kamal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Mustafa Kamal has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Abu Bakr El-Bediwi
Metal Physics Laboratory, Physics Department, Faculty of Science , Mansoura University , Mansoura, Egypt
2 shared publicationsAbbas Al- Bawee
1 shared publicationAbu Bakr El- Bediwi
1 shared publication- Abu Bakr El-Bediwi
Physics Department, Faculty of Science, Mansoura University, Mansoura, Egypt
1 shared publication - Abu Bakr El-Bediwi
Physics Department, Faculty of Science, Al-Azhar University, Cairo, Egypt
1 shared publication - El Said Gouda
Metal Physics Laboratory, Physics Department, Faculty of Science , Mansoura University , Mansoura, Egypt
1 shared publication
Latest Publications
- Open Access
- 1 February 2018
- Published by Oriental Scientific Publishing Company in Material Science Research India
- Vol. 15 (1) , 12-22
Electrochemical Corrosion Behavior, Microstructure and Soldering Properties of Tin Based Alloys
Microstructure, thermal behavior, wettability and electrochemical corrosion parameters of Sn82Bi15Zn3, Sn77Bi15Zn3Sb5, Sn79Bi15Zn3Ag3 and Sn81.3Bi15Zn3Cu0.7 [Jagadeees1] alloys have been studied and analyzed. The contact angles of used alloys varied from 21° to 31° which is less than 90° (low contact angle). That is meant, wetting process of these alloys are very favorable and the fluid will spread over a large area of the surface. Melting temperature values of Sn82Bi15Zn3, Sn77Bi15Zn3Sb5, Sn79Bi15Zn3Ag3 and Sn81.3Bi15Zn3Cu0.7 [Jagadeees2] alloys are lower than tin based eutectic solder alloys, (Sn- Zn or Sn- Cu or Sn- Sb), by 11% to 22%. Scanning electron microscope, x-ray analysis and differential scanning calorimetry graphs show that, the used alloys contained different phases. Corrosion rate of Sn82Bi15Zn3 alloy in HCl varied after adding alloying elements. Sn77Bi15Zn3Sb5 alloy has lowest corrosion rate value.
- 1 February 2018
- Published by Oriental Scientific Publishing Company in Material Science Research India
- Vol. 15 (1) , 12-22
Open AccessElectrochemical Corrosion Behavior, Microstructure and Soldering Properties of Tin Based Alloys
Microstructure, thermal behavior, wettability and electrochemical corrosion parameters of Sn82Bi15Zn3, Sn77Bi15Zn3Sb5, Sn79Bi15Zn3Ag3 and Sn81.3Bi15Zn3Cu0.7 [Jagadeees1] alloys have been studied and analyzed. The contact angles of used alloys varied from 21° to 31° which is less than 90° (low contact angle). That is meant, wetting process of these alloys are very favorable and the fluid will spread over a large area of the surface. Melting temperature values of Sn82Bi15Zn3, Sn77Bi15Zn3Sb5, Sn79Bi15Zn3Ag3 and Sn81.3Bi15Zn3Cu0.7 [Jagadeees2] alloys are lower than tin based eutectic solder alloys, (Sn- Zn or Sn- Cu or Sn- Sb), by 11% to 22%. Scanning electron microscope, x-ray analysis and differential scanning calorimetry graphs show that, the used alloys contained different phases. Corrosion rate of Sn82Bi15Zn3 alloy in HCl varied after adding alloying elements. Sn77Bi15Zn3Sb5 alloy has lowest corrosion rate value.
- 1 March 2008
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 163 (3) , 237-240
Electrical and mechanical properties of liquid rapidly quenched Cu–Al–Ni shape memory alloys
A series of Cu50–Al50−x –Ni x (x≥0) alloys exhibit stress-driven thermo elastic martensite transformation, which involves the ability to cover the desired shape at different temperatures. On cooling from high temperature, a displacive character of the transition is achieved, which confers it to the shape memory effect. The observed solidification rate effect on the martensite state was also taken into account. It allows explaining its sensitivity to the thermal treatments, which change the relative stability of both the parent phases existing prior to the transformation and the martensite. Resistance and mechanical measurements are also quantified.
- 1 March 2008
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 163 (3) , 237-240
Electrical and mechanical properties of liquid rapidly quenched Cu–Al–Ni shape memory alloys
A series of Cu50–Al50−x –Ni x (x≥0) alloys exhibit stress-driven thermo elastic martensite transformation, which involves the ability to cover the desired shape at different temperatures. On cooling from high temperature, a displacive character of the transition is achieved, which confers it to the shape memory effect. The observed solidification rate effect on the martensite state was also taken into account. It allows explaining its sensitivity to the thermal treatments, which change the relative stability of both the parent phases existing prior to the transformation and the martensite. Resistance and mechanical measurements are also quantified.
- 1 March 2006
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 161 (3) , 189-191
Mechanical properties of rapidly solidified of Cu-Sn shape memory alloys
The as-received melt spun Cu–40 wt.%Sn ribbon displayed the shape memory effect, which was observed by bending a ribbon and watching how it returns to its original shape upon heating. The temperature at which the melt spun Cu-40 wt.%Sn completely transformed in austenite upon heating was found to be 470 K. The temperature at which the alloy started to transform to martensite upon cooling was 310 K.
- 1 March 2006
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 161 (3) , 189-191
Mechanical properties of rapidly solidified of Cu-Sn shape memory alloys
The as-received melt spun Cu–40 wt.%Sn ribbon displayed the shape memory effect, which was observed by bending a ribbon and watching how it returns to its original shape upon heating. The temperature at which the melt spun Cu-40 wt.%Sn completely transformed in austenite upon heating was found to be 470 K. The temperature at which the alloy started to transform to martensite upon cooling was 310 K.
- 1 July 2005
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 160 (7) , 301-312
New lead-free solder alloy
As the electronics industry is moving towards lead-free manufacturing processes, a new lead-free solder alloy based on Sn–9Zn–1Bi–2Cu–In is described. The quaternary alloy with indium additions exhibits melting, wetting, and mechanical properties superior to those in binary, ternary, and quaternary alloys. Indium as a penternary addition decreases the melting point of this alloy to 181 °C which it is a lower value when compared with the eutectic Sn–Pb solder (183 °C), it decreases the contact angle to 23° which is very close to that for Sn–Pb solder alloy, it increases the Young’s modulus to higher values, and it increases its hardness to 19 kgf/mm2 when compared with 12.9 kgf/mm2 for the Sn–Pb solder alloy.
- 1 July 2005
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 160 (7) , 301-312
New lead-free solder alloy
As the electronics industry is moving towards lead-free manufacturing processes, a new lead-free solder alloy based on Sn–9Zn–1Bi–2Cu–In is described. The quaternary alloy with indium additions exhibits melting, wetting, and mechanical properties superior to those in binary, ternary, and quaternary alloys. Indium as a penternary addition decreases the melting point of this alloy to 181 °C which it is a lower value when compared with the eutectic Sn–Pb solder (183 °C), it decreases the contact angle to 23° which is very close to that for Sn–Pb solder alloy, it increases the Young’s modulus to higher values, and it increases its hardness to 19 kgf/mm2 when compared with 12.9 kgf/mm2 for the Sn–Pb solder alloy.
- 1 July 2005
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 160 (7) , 297-300
Effect of lead on microstructure and some physical properties of Sn–Zn–Cd alloy
The effect of lead on the structure, electrical resistivity, internal friction, elastic modulus and thermal properties of Sn81Zn9Cd10 ternary alloys have been investigated using different experimental techniques with their analysis. In addition, properties of this alloy were compared with other Sn–Zn or Sn–Zn–Cd alloys and commercial solder alloys. It has a higher electrical resistivity, internal friction and lower elastic modulus when compared with Sn–Zn or Sn–Zn alloys with other additions such as Cd, Bi or In. The Sn61Zn9Cd10Pb20 alloy has a lower melting point, electrical resistivity and internal friction when compared with the commercial Pb–Sn solder alloy, but it has a similar elastic modulus.
- 1 July 2005
- Published by Taylor & Francis in Radiation Effects and Defects in Solids
- Vol. 160 (7) , 297-300
Effect of lead on microstructure and some physical properties of Sn–Zn–Cd alloy
The effect of lead on the structure, electrical resistivity, internal friction, elastic modulus and thermal properties of Sn81Zn9Cd10 ternary alloys have been investigated using different experimental techniques with their analysis. In addition, properties of this alloy were compared with other Sn–Zn or Sn–Zn–Cd alloys and commercial solder alloys. It has a higher electrical resistivity, internal friction and lower elastic modulus when compared with Sn–Zn or Sn–Zn alloys with other additions such as Cd, Bi or In. The Sn61Zn9Cd10Pb20 alloy has a lower melting point, electrical resistivity and internal friction when compared with the commercial Pb–Sn solder alloy, but it has a similar elastic modulus.