Min Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Min Chen has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Xiaoming Zheng
Institute of Catalysis, Zhejiang University, Xixi Campus, Hangzhou, Zhejiang 310028, China
3 shared publicationsBo Xue
Institute of Catalysis, Department of Chemistry, Zhejiang University (Xixi Campus), Hangzhou 310028, China
2 shared publicationsLu-Jie Liu
Institute of Catalysis, Department of Chemistry, Zhejiang University (Xixi Campus), Hangzhou 310028, China
2 shared publicationsXiao-Ming Zheng
Institute of Catalysis, Department of Chemistry, Zhejiang University (Xixi Campus), Hangzhou 310028, China
2 shared publications- Chen Ling
Artie McFerrin Department of Chemical Engineering, Texas A&M University, College Station, TX 77843, USA
1 shared publication Chun'An Ma
State Key Laboratory Breeding Base for Green Chemistry Synthesis Technology, Zhejiang University of Technology, Hangzhou, Zhejiang 310032, China
1 shared publication
Latest Publications
- 30 July 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (82) , 66704-66710
Hydrogenation in supercritical conditions catalyzed by palladium supported on modified activated carbon
Biomass is expected to be a substitute for traditional fossil fuels because it is renewable and environmentally friendly. Bio-oil, as an important utilization of biomass, has a complex composition. Accordingly, it remains a great challenge for oxygenated compounds in bio-oil to be upgraded, especially for furfural. In this research, a highly active catalyst with 1 wt% palladium supported on activated carbon (Pd/AC) was prepared by impregnating Pd species on modified activated carbon, which was applied to furfural catalytic hydrogenation in super critical carbon dioxide (scCO2). The conversion rate (79%) was higher than that obtained in toluene as solvent (60%). A selectivity of furfuralcohol and tetrahydrofurfuryl alcohol of up to 100% was achieved in scCO2 conditions with no byproducts obtained. In contrast, the total selectivity was only 60% using ethanol as solvent. Meanwhile, the reaction conditions in the scCO2 including hydrogen pressure and catalyst amount have been investigated. The Pd/AC catalysts were characterized by XRD, SEM, IR and BET techniques. A green solvent, and high activity and selectivity present real advantages of this method over other methods.
- 30 July 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (82) , 66704-66710
Hydrogenation in supercritical conditions catalyzed by palladium supported on modified activated carbon
Biomass is expected to be a substitute for traditional fossil fuels because it is renewable and environmentally friendly. Bio-oil, as an important utilization of biomass, has a complex composition. Accordingly, it remains a great challenge for oxygenated compounds in bio-oil to be upgraded, especially for furfural. In this research, a highly active catalyst with 1 wt% palladium supported on activated carbon (Pd/AC) was prepared by impregnating Pd species on modified activated carbon, which was applied to furfural catalytic hydrogenation in super critical carbon dioxide (scCO2). The conversion rate (79%) was higher than that obtained in toluene as solvent (60%). A selectivity of furfuralcohol and tetrahydrofurfuryl alcohol of up to 100% was achieved in scCO2 conditions with no byproducts obtained. In contrast, the total selectivity was only 60% using ethanol as solvent. Meanwhile, the reaction conditions in the scCO2 including hydrogen pressure and catalyst amount have been investigated. The Pd/AC catalysts were characterized by XRD, SEM, IR and BET techniques. A green solvent, and high activity and selectivity present real advantages of this method over other methods.
- 27 April 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (50) , 40012-40017
Application of combined plasma-catalytic method for carbon particulate matter (PM) removal
The carbon particulate matter (PM) generated by diesel engine emissions has attracted world-wide attention because it has a remarkable impact on air quality and the human body. Therefore, research on the removal of carbon PM has attracted increasing interest recently. Additionally, oxidative removal of carbon PM requires high temperature due to its high activation energy. In this research, a promising technology of nonthermal plasma (NTP) combined with catalytic oxidation is reported. The effective removal of carbon PM under NTP conditions by the synergy of combining plasma with MnOx/CeO2 catalysts at low temperatures was reported in this paper. The removal efficiency of carbon PM on MnOx/CeO2 catalysts (Mn loading 5.0 wt%) can be as high as 85.2% and 94.3% at 20 °C and 200 °C respectively, at the discharge power of 18.0 W and air flow rate of 30 mL min−1. Moderate reaction conditions with low temperature but high removal efficiency are the advantages of the decomposition of carbon PM in a dielectric barrier discharge (DBD) reactor. It is proposed that reactive oxygen species produced under NTP conditions are responsible for carbon PM converting into CO2. Furthermore, various parameters such as temperature, discharge power and air flow rate under NTP were investigated in the present paper, as well as the reaction process of NTP. Meanwhile, the MnOx/CeO2 catalysts were also characterized by XRD and TEM techniques.
- 27 April 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (50) , 40012-40017
Application of combined plasma-catalytic method for carbon particulate matter (PM) removal
The carbon particulate matter (PM) generated by diesel engine emissions has attracted world-wide attention because it has a remarkable impact on air quality and the human body. Therefore, research on the removal of carbon PM has attracted increasing interest recently. Additionally, oxidative removal of carbon PM requires high temperature due to its high activation energy. In this research, a promising technology of nonthermal plasma (NTP) combined with catalytic oxidation is reported. The effective removal of carbon PM under NTP conditions by the synergy of combining plasma with MnOx/CeO2 catalysts at low temperatures was reported in this paper. The removal efficiency of carbon PM on MnOx/CeO2 catalysts (Mn loading 5.0 wt%) can be as high as 85.2% and 94.3% at 20 °C and 200 °C respectively, at the discharge power of 18.0 W and air flow rate of 30 mL min−1. Moderate reaction conditions with low temperature but high removal efficiency are the advantages of the decomposition of carbon PM in a dielectric barrier discharge (DBD) reactor. It is proposed that reactive oxygen species produced under NTP conditions are responsible for carbon PM converting into CO2. Furthermore, various parameters such as temperature, discharge power and air flow rate under NTP were investigated in the present paper, as well as the reaction process of NTP. Meanwhile, the MnOx/CeO2 catalysts were also characterized by XRD and TEM techniques.
- 1 December 2012
- Published by Springer Nature in Journal of Porous Materials
- Vol. 20 (4) , 839-844
The preparation of ZSM-5 zeolite@Cu/stainless steel as a dual functional material
- 1 December 2012
- Published by Springer Nature in Journal of Porous Materials
- Vol. 20 (4) , 839-844
The preparation of ZSM-5 zeolite@Cu/stainless steel as a dual functional material
- 28 January 2012
- Published by Springer Nature in Journal of Central South University
- Vol. 19 (2) , 319-323
Preparation process and characterization of new Pt/stainless steel wire mesh catalyst designed for volatile organic compounds elimination
- 28 January 2012
- Published by Springer Nature in Journal of Central South University
- Vol. 19 (2) , 319-323
Preparation process and characterization of new Pt/stainless steel wire mesh catalyst designed for volatile organic compounds elimination
- 30 October 2009
- Published by Wiley in Chinese Journal of Chemistry
- Vol. 27 (10) , 1903-1906
Pd‐Mn/Stainless Steel Wire Mesh Catalyst for Catalytic Oxidation of Toluene, Acetone and Ethyl Acetate
- 30 October 2009
- Published by Wiley in Chinese Journal of Chemistry
- Vol. 27 (10) , 1903-1906
Pd‐Mn/Stainless Steel Wire Mesh Catalyst for Catalytic Oxidation of Toluene, Acetone and Ethyl Acetate
- 1 July 2008
- Published by Pleiades Publishing Ltd in Kinetics and Catalysis
- Vol. 49 (4) , 493-498
The support effect on PdO/Ce0.7Zr0.3Ba0.1O2.1 and CuO/Ce0.7Zr0.3Ba0.1O2.1 catalysts
Ce0.7Zr0.3Ba0.1O2.1 mixed oxides (denoted as CZB) were prepared using macromolecule surface modified methods and used as supports to prepare low palladium content of PdO/CZB model catalysts. CuO/CZB series of catalysts were also prepared for comparison. The catalytic activity of the PdOCZB and CuO/CZB series of catalysts for low-temperature CO oxidation was investigated. A significant influence of the Ce0.7Zr0.3Ba0.1O2.1 support on the catalytic performance has been found. Using Ce0.7Zr0.3Ba0.1O2.1 as catalyst support increased the activity of CO oxidation and promoted the thermal stability significantly. It was found that the transition metal supported catalyst of 10.0 wt % CuO/CZB obtained a good result, as did the precious metal supported catalysts of 0.75 wt % PdO/CZB. The catalytic behaviors and thermal stability of PdO/CZB and CuO/CZB catalysts greatly depended on the support effect. The nature of Ce0.7Zr0.3Ba0.1O2.1 support was also characterized by surface area (BET method), x-ray powder diffraction (XRD), transmission electron microscopy (TEM), temperature programmed reduction with hydrogen (H2-TPR) and X-ray photoelectron spectroscopy (XPS) technologies.
- 1 July 2008
- Published by Pleiades Publishing Ltd in Kinetics and Catalysis
- Vol. 49 (4) , 493-498
The support effect on PdO/Ce0.7Zr0.3Ba0.1O2.1 and CuO/Ce0.7Zr0.3Ba0.1O2.1 catalysts
Ce0.7Zr0.3Ba0.1O2.1 mixed oxides (denoted as CZB) were prepared using macromolecule surface modified methods and used as supports to prepare low palladium content of PdO/CZB model catalysts. CuO/CZB series of catalysts were also prepared for comparison. The catalytic activity of the PdOCZB and CuO/CZB series of catalysts for low-temperature CO oxidation was investigated. A significant influence of the Ce0.7Zr0.3Ba0.1O2.1 support on the catalytic performance has been found. Using Ce0.7Zr0.3Ba0.1O2.1 as catalyst support increased the activity of CO oxidation and promoted the thermal stability significantly. It was found that the transition metal supported catalyst of 10.0 wt % CuO/CZB obtained a good result, as did the precious metal supported catalysts of 0.75 wt % PdO/CZB. The catalytic behaviors and thermal stability of PdO/CZB and CuO/CZB catalysts greatly depended on the support effect. The nature of Ce0.7Zr0.3Ba0.1O2.1 support was also characterized by surface area (BET method), x-ray powder diffraction (XRD), transmission electron microscopy (TEM), temperature programmed reduction with hydrogen (H2-TPR) and X-ray photoelectron spectroscopy (XPS) technologies.
- 11 May 2007
- Published by Wiley in Chinese Journal of Chemistry
- Vol. 25 (5) , 666-669
Synthesis and Characterization of New Material‐‐La/Zr/MMT Employed in Acetone Oxidation
- 11 May 2007
- Published by Wiley in Chinese Journal of Chemistry
- Vol. 25 (5) , 666-669
Synthesis and Characterization of New Material‐‐La/Zr/MMT Employed in Acetone Oxidation
- 9 June 2005
- Published by Elsevier in Journal of Molecular Catalysis A: Chemical
- Vol. 237 (1-2) , 132-136
Synthesis of nanoparticle Ce–Mg–O mixed oxide as efficient support for methane oxidation
- 9 June 2005
- Published by Elsevier in Journal of Molecular Catalysis A: Chemical
- Vol. 237 (1-2) , 132-136
Synthesis of nanoparticle Ce–Mg–O mixed oxide as efficient support for methane oxidation