MSMichael Schroll

Michael Schroll

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Michael Schroll has a total of 62 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Investigating the Unsteady Dynamics of a Multi-Jet Impingement Cooling Flow Using Large Eddy Simulation

    by Christian Morsbach, Marcel Matha, Robin G. Brakmann, Sadiya Tabassum, Michael Bergmann, Michael Schroll, Christian Willert, Edmund Kügeler

    We investigate the unsteady behavior of an in-line jet impingement array of nine jets at a Reynolds number of 10,000 in a narrow channel subjected to a developing cross flow of up to 25% of the bulk jet velocity. To this end, we present an improved version of a previously published large eddy simulation (LES) now with resolved turbulence at the inflow boundaries. After a careful analysis of the transient behavior and statistical convergence of the LES, we discuss the time-averaged heat transfer characteristics of the configuration compared to numerical references of similar configurations. We then show how the large-scale unsteadiness increases from jet to jet. Both space-only and spectral proper orthogonal decompositions (POD and SPOD) are used to discuss the large-scale organization of single jets and multiple jets in combination. The latter shows a qualitative change in the unsteady behavior of the temperature footprint on the impingement wall with increasing cross flow.


  • Assessment of Computational Fluid Dynamic Modeling of Multi-Jet Impingement Cooling and Validation With the Experiments

    by Sadiya Tabassum, Michael Hilfer, Robin G. Brakmann, Christian Morsbach, Christian Willert, Marcel Matha, Michael Schroll

    The current study involves numerical and experimental investigations of circular in-line jets impinging on a heated flat plate. The generic configuration is characterized by nine jets, each with a diameter of D = 0.0152 m. The jets are influenced by a self-generating crossflow and are positioned at a nozzle-to-plate distance (H/D) of 5 and a jet pitch (p/D) of 5. The steady Reynolds-averaged Navier–Stokes (RANS) simulations are performed for turbulent jet Reynolds numbers with the in-house CFD code TRACE. The Menter k–ω shear stress transport (SST) model is applied for turbulence modeling and the turbulent scalar fluxes are modeled based on the Reynolds analogy for a constant turbulent Prandtl number. To gain a closer insight into the impingement jet physics, high-resolution near-wall velocity and thermal fields are obtained through large eddy simulations (LESs) and measurements from particle image velocimetry (PIV). Focus is laid on the comparison of RANS results with the LES data and the experimental data. The results exhibit a qualitative similarity between the simulations and the experiments. Furthermore, correlations of the Nusselt number from the literature are used to validate the simulation results.


  • Open Access

    Time-resolved flow field investigation in an industrial centrifugal compressor application involving TR-PIV synchronized with unsteady pressure measurements

    by Joachim Klinner, Melanie Voges, Michael Schroll, Alessandro Bassetti, Christian Willert

    We report on combined velocity and unsteady pressure measurements obtained on an radial compressor with vaneless diffuser and asymmetric volute. Time-resolved PIV recordings were acquired at 26 kHz both upstream of the impeller as well as within the vaneless diffusor at several rotation speeds at clean conditions and prior to the onset of instabilities within the rotor. The velocity data was acquired with a high-repetition rate, double-pulse laser system consisting of two combined DPSS lasers and a high-speed CMOS camera that was synchronized with multi-point unsteady pressure measurements. Details on the facility, the utilized instrumentation and data processing are provided with particular focus on the spectral and coherence analysis. Power spectra obtained from time records of the inlet velocity and unsteady pressure reveal an increase of low-frequency fluctuations below the blade passing frequency and the occurrence of a mode-locked behaviour indicating the presence of rotating instabilities. High levels of correlation between velocity and unsteady pressure signals not only confirm the temporal coherence of the acquired data but also reveal a direct coupling between flow field and pressure signature that is more prominent upstream of the rotor rather than in the diffusor.


  • Quantitative Flow Imaging of Film Cooling Jets in a Cross-Flow Using Particle Image Velocimetry and Computational Fluid Dynamics

    by Robin G. Brakmann, Robin Schöffler, Frank Kocian, Michael Schroll, Christian Willert, Martin Müller, Edmund Kügeler

    The investigated generic configuration consists of cylindrical film cooling holes with a diameter of D = 8.4 mm and an inclination angle of α = 35°. The jets are characterized by a momentum flux ratio of I = 0.63, a density ratio of DR = 0.94 and a cross-flow Reynolds number of Re = 5500. Stereoscopic PIV allows creating a (pseudo) three dimensional image of the flow field. High resolution PIV is used to evaluate velocity fluctuations. The numerical model uses the SST and an EARSM turbulence model. The turbulent scalar fluxes are computed by a constant turbulent Prandtl number as well as algebraic models for the turbulent heat flux. The presented results consist of field cuts and line profiles of the velocity, vorticity and turbulent kinetic energy. All considered numerical options can predict the velocity field accurately, the SST turbulence model is the numerically most stable model and has the lowest demands in computational costs.


  • Open Access

    Influence of Fluidic Control in a Staged Lean Jet Engine Burner on Combustor Performance

    by Seiji Yoshida, Christoph Hassa, Takeshi Yamamoto, Johannes Heinze, Michael Schroll

    To improve the turn-down ratio of a lean combustor, which has the greatest potential for reducing NOx emissions from jet engines, fuel staging is commonly employed. To further extend the stable operation range, air staging with a fluidic element is also considered. The influence of fluidic control on combustion was analyzed to better understand fluidic element-burner interactions. The pressure loss of each fluidic element was determined by measuring the pressure at the element exits. The effect of fluidic control on the atomization, fuel distribution, and flow field was investigated using optical, noninvasive techniques. The combustion performance of the burner with the fluidic element was evaluated using exhaust gas analyses. The pressure losses of the swirlers and fuel mixers were varied depending on the bleed air from the fluidic element. Under the idle condition, the reduction of pressure loss in the pilot fuel mixer resulted in inferior atomization due to the reduced gas velocity around the fuel film, which had a positive effect on lean blowout. Under the cruise condition and the staged mode, the reduction of the pilot air flow increased the equivalence ratio of the lean pilot stage and resulted in higher combustion efficiency.


  • Experimental and Numerical Investigation of 3-D Corner Separation in a Channel Flow with Adverse Pressure Gradient

    by Joachim Klinner, Michael Schroll, Christian Morsbach, Felix Möller, Christian Willert


  • Modification of the SSG/LRR- $\omega $ RSM for Turbulent Boundary Layers at Adverse Pressure Gradient with Separation Using the New DLR VicToria Experiment

    by Tobias Knopp, Matteo Novara, Daniel Schanz, Reinhard Geisler, Florian Philipp, Michael Schroll, Christian Willert, Andreas Schröder


  • Investigation of the Reacting Flow Field of a Lean Burn Injector With Varying Degree of Swirl at Elevated Pressure Condition

    by Christoph Hassa, Ulrich Meier, Johannes Heinze, Eggert Magens, Michael Schroll, I. Bagchi

    Two RR Lean Direct Injection (LDI) injector versions with different amounts of pilot swirl were investigated. Experiments, performed at elevated pressure and temperature, corresponding to engine conditions at idle include Mie scattering. LII and absorption measurements are used for soot concentration within the primary zone. The soot emission at the outlet is measured by an SMPS instrument. These experimental studies are complemented with PIV measurements. The acquired data allows evaluation of the combustion process from the liquid phase, followed by evaporation, reaction and finally soot production with high spatial resolution. The change of swirl produced rather moderate changes in the flow field, nevertheless qualitative changes in the fuel placement were observed. Starting from there, differences in heat release and soot formation can be explained, which lead to larger changes of soot emission. These observations show that a good knowledge of the interaction of gas and liquid phase is necessary to predict the occurrence of behavioral changes in the operating regime.


  • Flow Field Characterization at the Outlet of a Lean Burn Single-Sector Combustor by Laser-Optical Methods

    by Michael Schroll, Ulrich Doll, Guido Stockhausen, Ulrich Meier, Chris Willert, Christoph Hassa, Imon Bagchi

    High overall pressure ratio (OPR) engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. Lean burn fuel injectors dominate the combustor exit conditions. This is due to the fact that they pass a majority of the total combustor flow, and to the lack of mixing jets like in a conventional combustor. With the transition to high-pressure engines, it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling. Velocity distributions and their fluctuations at the combustor exit for lean burn are of special interest as they can influence the efficiency and capacity of the turbine. A lean burn single-sector combustor was designed and built at DLR, providing optical access to its rectangular exit section. The sector was operated with a fuel-staged lean burn injector. Measurements were performed under idle and cruise operating conditions. Two velocity measurement techniques were used in the demanding environment of highly luminous flames under elevated pressures: particle image velocimetry (PIV) and filtered Rayleigh scattering (FRS). The latter was used for the first time in an aero-engine combustor environment. In addition to a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its practicality for a potential future application in a full annular combustor with restricted optical access.


  • Flow Field Characterization at the Outlet of a Lean Burn Single Sector Combustor by Laser-Optical Methods

    by M. Schroll, U. Doll, G. Stockhausen, U. Meier, C. Willert, C. Hassa, I. Bagchi

    High OPR engine cycles for reduced NOx emissions will generate new aggravated requirements and boundary conditions by implementing low emission combustion technologies into advanced engine architectures. Lean burn combustion systems will have a significant impact on the temperature and velocity traverse at the combustor exit. Lean burn fuel injectors dominate the combustor exit conditions. This is due to the fact that they pass a majority of the total combustor flow, and to the lack of mixing jets like in a conventional combustor. With the transition to high pressure engines it is essential to fully understand and determine the high energetic interface between combustor and turbine to avoid excessive cooling, which has a detrimental impact on turbine and overall engine efficiency. Velocity distributions and their fluctuations at the combustor exit for lean burn are of special interest as they can influence the efficiency and capacity of the turbine. Within the EU project LEMCOTEC, a lean burn single sector combustor was designed and built at DLR, providing optical access to its rectangular exit section. The sector was operated with a fuel staged lean burn injector from Rolls-Royce Deutschland. Measurements were performed under various operating conditions, covering idle and cruise operation. Two techniques were used to perform velocity measurements at the combustor exit in the demanding environment of highly luminous flames under elevated pressures: Particle Image Velocimetry (PIV) and Filtered Rayleigh Scattering (FRS). The latter was used for the first time in an aero-engine combustor environment. In addition to a conventional signal detection arrangement, FRS was also applied with an endoscope for signal collection, to assess its practicality for a potential future application in a full annular combustor with restricted optical access. Both measurement techniques are complementary in several respects, which justified their respective application and comparative assessment. PIV is able to record instantaneous velocity distributions and is therefore capable to deliver higher velocity moments, in addition to temporal averages. Applied in two orthogonal traversable light sheet arrangements, it could be used to map all three velocity components across the entire combustor cross section, and obtain data on velocity variances, cross-correlations and turbulence intensities. FRS is limited to measurements of average velocities, as long sampling times are required due to the weak physical process of Rayleigh scattering. However, FRS has two advantages: It requires no particle seeding, because it is based on the measurement of a molecular Doppler shift, and it can provide temperature information simultaneously. This contribution complements a second paper (GT2016-56370) focusing on the measurement of temperature distributions at the same combustor exit section by laser-based optical methods.