Ho-Yun Nam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ho-Yun Nam has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Byoung-Hae Choi
3 shared publicationsJong-Bum Kim
2 shared publicationsJong-Man Kim
Fluid Engineering Division, Korea Atomic Energy Research Institute, 150 Deokjin-dong, Yuseong-gu, Daejeon, 305-353, Korea
2 shared publicationsMann Cho
Liquid Metal Reactor Coolant Department , Korea Atomic Energy Research Institute , P.O. Box 105, Yousung, Daejon, 305-600, Korea
2 shared publicationsSeok Ki Choi
Liquid Metal Reactor Coolant Department , Korea Atomic Energy Research Institute , P.O. Box 105, Yousung, Daejon, 305-600, Korea
2 shared publicationsByung-Ho Kim
Fluid Engineering Division, Korea Atomic Energy Research Institute, 150 Deokjin-dong, Yuseong-gu, Daejeon, 305-353, Korea
1 shared publication
Latest Publications
- 1 October 2011
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - B
- Vol. 35 (10) , 1075-1081
Comparison of the Friction-Loss Coefficient for the Gap of Two Contact Surfaces and a Crack
- 1 October 2011
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - B
- Vol. 35 (10) , 1075-1081
Comparison of the Friction-Loss Coefficient for the Gap of Two Contact Surfaces and a Crack
- Open Access
- 1 September 2010
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - A
- Vol. 34 (9) , 1217-1225
Design Concept and Technology Development of a Double-Wall-Tube Steam Generator
- 1 September 2010
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - A
- Vol. 34 (9) , 1217-1225
Open AccessDesign Concept and Technology Development of a Double-Wall-Tube Steam Generator
- 28 October 2008
- Published by ASME International in Journal of Fluids Engineering
- Vol. 130 (12) , 121106
Experimental Study on the Amplitude of a Free Surface Fluctuation
An experimental study was performed to measure the fluctuation phenomena of a free surface in a vessel with or without an internal structure. A flow enters from the bottom and flows out of the side wall nozzles. Characteristics of the free surface fluctuation are investigated in terms of the geometry factors of the vessel and the flow rate. A modified Froude number is proposed to describe the amplitude of a free surface fluctuation. The fluctuation amplitude increases stably with an increase in the ratio of the vessel diameter to the water level in a vessel without an internal structure. When the ratio is greater than about 2, the fluctuation decreases suddenly with an increase in the ratio and it becomes unstable. The fluctuation amplitude is linearly proportional to the square of the Froude number. The amplitude of a free surface fluctuation increases with an increase in the height of an internal structure, but this increasing ratio is reduced when the height becomes higher. Two correlations were developed in terms of the Froude number and geometry factors to predict the amplitude of the free surface fluctuation in a vessel with or without an internal structure.
- 28 October 2008
- Published by ASME International in Journal of Fluids Engineering
- Vol. 130 (12) , 121106
Experimental Study on the Amplitude of a Free Surface Fluctuation
An experimental study was performed to measure the fluctuation phenomena of a free surface in a vessel with or without an internal structure. A flow enters from the bottom and flows out of the side wall nozzles. Characteristics of the free surface fluctuation are investigated in terms of the geometry factors of the vessel and the flow rate. A modified Froude number is proposed to describe the amplitude of a free surface fluctuation. The fluctuation amplitude increases stably with an increase in the ratio of the vessel diameter to the water level in a vessel without an internal structure. When the ratio is greater than about 2, the fluctuation decreases suddenly with an increase in the ratio and it becomes unstable. The fluctuation amplitude is linearly proportional to the square of the Froude number. The amplitude of a free surface fluctuation increases with an increase in the height of an internal structure, but this increasing ratio is reduced when the height becomes higher. Two correlations were developed in terms of the Froude number and geometry factors to predict the amplitude of the free surface fluctuation in a vessel with or without an internal structure.
- 27 October 2004
- Published by ASME International in Journal of Fluids Engineering
- Vol. 127 (2) , 388-392
Development of an Experimental Correlation for a Pressure Loss at a Side Orifice
An experimental study has been carried out to measure the pressure loss at the side orifice of a liquid metal reactor fuel assembly. The characteristics of the pressure loss at the side orifice are investigated using the experimental data measured from 17 different types of side orifices that have different geometric shapes, dimensions, and arrangements of nozzles, and a correlation that covers the whole flow range by one equation is developed. The error range of the correlation is within ±10%, and most of the errors occurred in a region where the Reynolds number is small. The range of Reynolds numbers based on the hydraulic diameter of the orifice is 2000–350,000. It is found that the geometric factor is the most important parameter for the pressure loss when the Reynolds number is >30,000. As the Reynolds number becomes smaller, its effect becomes larger, and when the Reynolds number is small, it is the most important parameter for the pressure loss at the side orifices. The measured data shows a trend that the pressure loss coefficient increases as the number of orifices increases, and the effect of the longitudinal arrangement is small.
- 27 October 2004
- Published by ASME International in Journal of Fluids Engineering
- Vol. 127 (2) , 388-392
Development of an Experimental Correlation for a Pressure Loss at a Side Orifice
An experimental study has been carried out to measure the pressure loss at the side orifice of a liquid metal reactor fuel assembly. The characteristics of the pressure loss at the side orifice are investigated using the experimental data measured from 17 different types of side orifices that have different geometric shapes, dimensions, and arrangements of nozzles, and a correlation that covers the whole flow range by one equation is developed. The error range of the correlation is within ±10%, and most of the errors occurred in a region where the Reynolds number is small. The range of Reynolds numbers based on the hydraulic diameter of the orifice is 2000–350,000. It is found that the geometric factor is the most important parameter for the pressure loss when the Reynolds number is >30,000. As the Reynolds number becomes smaller, its effect becomes larger, and when the Reynolds number is small, it is the most important parameter for the pressure loss at the side orifices. The measured data shows a trend that the pressure loss coefficient increases as the number of orifices increases, and the effect of the longitudinal arrangement is small.
- 1 July 1995
- Published by Taylor & Francis in Numerical Heat Transfer, Part B: Fundamentals
- Vol. 28 (1) , 23-38
EVALUATION OF A HIGHER-ORDER BOUNDED CONVECTION SCHEME: THREE-DIMENSIONAL NUMERICAL EXPERIMENTS
This article presents a detailed three-dimensional evaluation of a higher-order bounded convection scheme. A high-resolution and bounded discretization scheme named COPIA, which is composed of piecewise linear functions in the normalized variable diagram, is proposed. The scheme is applied to the three-dimensional test problems to assess its capabilities. The results of numerical experiments show that the tested bounded scheme resolves the boundedness problem white retaining the accuracy of a higher-order scheme.
- 1 July 1995
- Published by Taylor & Francis in Numerical Heat Transfer, Part B: Fundamentals
- Vol. 28 (1) , 23-38
EVALUATION OF A HIGHER-ORDER BOUNDED CONVECTION SCHEME: THREE-DIMENSIONAL NUMERICAL EXPERIMENTS
This article presents a detailed three-dimensional evaluation of a higher-order bounded convection scheme. A high-resolution and bounded discretization scheme named COPIA, which is composed of piecewise linear functions in the normalized variable diagram, is proposed. The scheme is applied to the three-dimensional test problems to assess its capabilities. The results of numerical experiments show that the tested bounded scheme resolves the boundedness problem white retaining the accuracy of a higher-order scheme.
- 1 January 1993
- Published by Taylor & Francis in Numerical Heat Transfer, Part B: Fundamentals
- Vol. 23 (1) , 21-41
USE OF THE MOMENTUM INTERPOLATION METHOD FOR NUMERICAL SOLUTION OF INCOMPRESSIBLE FLOWS IN COMPLEX GEOMETRIES: CHOOSING CELL FACE VELOCITIES
The momentum interpolation method developed by Rhie and Chow [1rsqb; is further refined and extended to employ the curvilinear covariant velocity components as cell face velocities. The related pressure-velocity coupling technique is described. The relative performances of the proposed scheme and of the scheme based on the contravariant cell face velocities are examined through applications to several test problems. The present scheme, based on the covariant cell face velocities, always provides simple and diagonal-dominant pressure and pressure-correction equations and shows good convergence and stability behavior even in a strongly nonorthogonal grid situation.
- 1 January 1993
- Published by Taylor & Francis in Numerical Heat Transfer, Part B: Fundamentals
- Vol. 23 (1) , 21-41
USE OF THE MOMENTUM INTERPOLATION METHOD FOR NUMERICAL SOLUTION OF INCOMPRESSIBLE FLOWS IN COMPLEX GEOMETRIES: CHOOSING CELL FACE VELOCITIES
The momentum interpolation method developed by Rhie and Chow [1rsqb; is further refined and extended to employ the curvilinear covariant velocity components as cell face velocities. The related pressure-velocity coupling technique is described. The relative performances of the proposed scheme and of the scheme based on the contravariant cell face velocities are examined through applications to several test problems. The present scheme, based on the covariant cell face velocities, always provides simple and diagonal-dominant pressure and pressure-correction equations and shows good convergence and stability behavior even in a strongly nonorthogonal grid situation.