Tatsuya Kodama
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Tatsuya Kodama has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Nobuyuki Gokon
Niigata University
13 shared publications Koji Matsubara
Faculty of Engineering, Niigata University, 8050 Ikarashi 2-nocho, Niigata 950-2181, Japan
6 shared publications- Ken-Ichi Shimizu
Hokkaido University N-21, W-10
5 shared publications Sridhar Komarneni
Materials Research Institute and Department of Crop and Soil Sciences , The Pennsylvania State University , University Park, Pennsylvania, USA
5 shared publicationsTsuyoshi Hatamachi
Department of Chemistry & Chemical Engineering, Faculty of Engineering, Niigata University, 8050 Ikarashi 2-nocho, Nishi-ku, Niigata 950-2181, Japan
5 shared publications- Selvan Bellan
Faculty of Engineering Niigata University Niigata Japan
4 shared publications
Latest Publications
- Open Access
Development of Synthesis and Fabrication Process for Mn-CeO2 Foam via Two-Step Water-Splitting Cycle Hydrogen Production
The effects of doping manganese ions into a cerium oxide lattice for a thermochemical two-step water-splitting cycle to produce oxygen and hydrogen and new synthesis methods were experimentally investigated. In order to comparison of oxygen/hydrogen producing performance, pristine CeO2, a coprecipitation method for Mn-CeO2, and a direct depositing method for Mn-CeO2 with different particle sizes (50~75, 100–212, over 212 μm) and doping extents (0, 5, 15 mol%) were tested in the context of synthesis and fabrication processes of reactive metal oxide coated ceramic foam devices. Sample powders were coated onto zirconia (magnesium partially stabilized zirconia oxide, MPSZ) porous foam at 30 weight percent using spin coating or a direct depositing method, tested using a solar reactor at 1400 °C as a thermal reduction step and at 1200 °C as a water decomposition step for five repeated cycles. The sample foam devices were irradiated using a 3-kWth sun-simulator, and all reactive foam devices recorded successful oxygen/hydrogen production using the two-step water-splitting cycles. Among the seven sample devices, the 5 mol% Mn-CeO2 foam device, that synthesized using the coprecipitation method, showed the greatest hydrogen production. The newly suggested direct depositing method, with its contemporaneous synthesis and coating of the Mn-CeO2 foam device, showed successful oxygen/hydrogen production with a reduction in the manufacturing time and reactants, which was lossless compared to conventional spin coating processes. However, proposed direct depositing method still needs further investigation to improve its stability and long-term device durability.
Open AccessDevelopment of Synthesis and Fabrication Process for Mn-CeO2 Foam via Two-Step Water-Splitting Cycle Hydrogen Production
The effects of doping manganese ions into a cerium oxide lattice for a thermochemical two-step water-splitting cycle to produce oxygen and hydrogen and new synthesis methods were experimentally investigated. In order to comparison of oxygen/hydrogen producing performance, pristine CeO2, a coprecipitation method for Mn-CeO2, and a direct depositing method for Mn-CeO2 with different particle sizes (50~75, 100–212, over 212 μm) and doping extents (0, 5, 15 mol%) were tested in the context of synthesis and fabrication processes of reactive metal oxide coated ceramic foam devices. Sample powders were coated onto zirconia (magnesium partially stabilized zirconia oxide, MPSZ) porous foam at 30 weight percent using spin coating or a direct depositing method, tested using a solar reactor at 1400 °C as a thermal reduction step and at 1200 °C as a water decomposition step for five repeated cycles. The sample foam devices were irradiated using a 3-kWth sun-simulator, and all reactive foam devices recorded successful oxygen/hydrogen production using the two-step water-splitting cycles. Among the seven sample devices, the 5 mol% Mn-CeO2 foam device, that synthesized using the coprecipitation method, showed the greatest hydrogen production. The newly suggested direct depositing method, with its contemporaneous synthesis and coating of the Mn-CeO2 foam device, showed successful oxygen/hydrogen production with a reduction in the manufacturing time and reactants, which was lossless compared to conventional spin coating processes. However, proposed direct depositing method still needs further investigation to improve its stability and long-term device durability.
- 22 January 2019
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 141 (2)
Japan Aims at Establishing a Hydrogen-Based Society—Can Solar Thermochemistry Contribute?
Essay for the JSEE special issue.
- 22 January 2019
- Published by ASME International in Journal of Solar Energy Engineering
- Vol. 141 (2)
Japan Aims at Establishing a Hydrogen-Based Society—Can Solar Thermochemistry Contribute?
Essay for the JSEE special issue.
- 8 November 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2033 (1) , 130009
Particle fluidized bed receiver/reactor with a beam-down solar concentrating optics: Performance test of two-step water splitting with ceria particles using 30-kWth sun-simulator
The first performance test of a novel windowed solar fluidized bed reactor was carried out for a two-step water splitting cycle with ceria particles by using a 30-kWth sun-simulator. O2 and H2 were successfully produced by the reactor system. During the thermal reduction step of the two-step water splitting, a fluidized bed of ceria particles was created by passing N2 gas through the perforated bottom plate of the reactor, and about 30 kWth of high flux visible light from 19 xenon-arc lamps of the sun-simulator was directed inside the reactor through a quartz window to directly irradiate the top of the fluidized bed. The central bed temperature reached the temperature of 1400 to 1500°C in the thermal reduction step. The subsequent water decomposition or hydrolysis step was performed at the central bed temperature of 800 - 900°C. About 6 - 12 Ndm3 of hydrogen was produced by one cycle.
- 8 November 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2033 (1) , 130009
Particle fluidized bed receiver/reactor with a beam-down solar concentrating optics: Performance test of two-step water splitting with ceria particles using 30-kWth sun-simulator
The first performance test of a novel windowed solar fluidized bed reactor was carried out for a two-step water splitting cycle with ceria particles by using a 30-kWth sun-simulator. O2 and H2 were successfully produced by the reactor system. During the thermal reduction step of the two-step water splitting, a fluidized bed of ceria particles was created by passing N2 gas through the perforated bottom plate of the reactor, and about 30 kWth of high flux visible light from 19 xenon-arc lamps of the sun-simulator was directed inside the reactor through a quartz window to directly irradiate the top of the fluidized bed. The central bed temperature reached the temperature of 1400 to 1500°C in the thermal reduction step. The subsequent water decomposition or hydrolysis step was performed at the central bed temperature of 800 - 900°C. About 6 - 12 Ndm3 of hydrogen was produced by one cycle.
- 1 January 2018
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Hokuriku-Shinetsu Branch
- Vol. 2018.55, E043
Numerical analysis of two-tower type fluized Bed Receiver
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。
- 1 January 2018
- Published by Japan Society of Mechanical Engineers in The Proceedings of Conference of Hokuriku-Shinetsu Branch
- Vol. 2018.55, E043
Numerical analysis of two-tower type fluized Bed Receiver
総合学術電子ジャーナルサイト「J-STAGE」-国内で発行された学術論文全文を読むことのできる、日本最大級の総合電子ジャーナルプラットフォームです。
- 27 June 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1850 (1) , 100008
Thermal storage/discharge performances of Cu-Si alloy for solar thermochemical process
The present authors (Niigata University, Japan) have developed a tubular reactor system using novel “double-walled” reactor/receiver tubes with carbonate molten-salt thermal storage as a phase change material (PCM) for solar reforming of natural gas and with Al-Si alloy thermal storage as a PCM for solar air receiver to produce high-temperature air. For both of the cases, the high heat capacity and large latent heat (heat of solidification) of the PCM phase circumvents the rapid temperature change of the reactor/receiver tubes at high temperatures under variable and uncontinuous characteristics of solar radiation. In this study, we examined cyclic properties of thermal storage/discharge for Cu-Si alloy in air stream in order to evaluate a potentiality of Cu-Si alloy as a PCM thermal storage material. Temperature-increasing performances of Cu-Si alloy are measured during thermal storage (or heat-charge) mode and during cooling (or heat-discharge) mode. A oxidation state of the Cu-Si alloy after the cyclic reaction was evaluated by using electron probe micro analyzer (EPMA).
- 27 June 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1850 (1) , 100008
Thermal storage/discharge performances of Cu-Si alloy for solar thermochemical process
The present authors (Niigata University, Japan) have developed a tubular reactor system using novel “double-walled” reactor/receiver tubes with carbonate molten-salt thermal storage as a phase change material (PCM) for solar reforming of natural gas and with Al-Si alloy thermal storage as a PCM for solar air receiver to produce high-temperature air. For both of the cases, the high heat capacity and large latent heat (heat of solidification) of the PCM phase circumvents the rapid temperature change of the reactor/receiver tubes at high temperatures under variable and uncontinuous characteristics of solar radiation. In this study, we examined cyclic properties of thermal storage/discharge for Cu-Si alloy in air stream in order to evaluate a potentiality of Cu-Si alloy as a PCM thermal storage material. Temperature-increasing performances of Cu-Si alloy are measured during thermal storage (or heat-charge) mode and during cooling (or heat-discharge) mode. A oxidation state of the Cu-Si alloy after the cyclic reaction was evaluated by using electron probe micro analyzer (EPMA).
- 27 June 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1850 (1) , 080006
Numerical analysis of fluid flow and heat transfer during melting inside a cylindrical container for thermal energy storage system
This paper presents a numerical analysis of unconstrained melting of high temperature(>1000K) phase change material (PCM) inside a cylindrical container. Sodium chloride and Silicon carbide have been used as phase change material and shell of the capsule respectively. The control volume discretization approach has been used to solve the conservation equations of mass, momentum and energy. The enthalpy-porosity method has been used to track the solid-liquid interface of the PCM during melting process. Transient numerical simulations have been performed in order to study the influence of radius of the capsule and the Stefan number on the heat transfer rate. The simulation results show that the counter-clockwise Buoyancy driven convection over the top part of the solid PCM enhances the melting rate quite faster than the bottom part.
- 27 June 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1850 (1) , 080006
Numerical analysis of fluid flow and heat transfer during melting inside a cylindrical container for thermal energy storage system
This paper presents a numerical analysis of unconstrained melting of high temperature(>1000K) phase change material (PCM) inside a cylindrical container. Sodium chloride and Silicon carbide have been used as phase change material and shell of the capsule respectively. The control volume discretization approach has been used to solve the conservation equations of mass, momentum and energy. The enthalpy-porosity method has been used to track the solid-liquid interface of the PCM during melting process. Transient numerical simulations have been performed in order to study the influence of radius of the capsule and the Stefan number on the heat transfer rate. The simulation results show that the counter-clockwise Buoyancy driven convection over the top part of the solid PCM enhances the melting rate quite faster than the bottom part.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Particles fluidized bed receiver/reactor tests with quartz sand particles using a 100-kWth beam-down solar concentrating system at Miyazaki
A window-type, solar fluidized bed receiver with quartz sand particles was tested by a 100-kWth novel beam-down solar concentrating system at Miyazaki, Japan. A compound parabolic concentrator (CPC) was placed above the quartz window of the receiver to increase the concentration of the solar fluxes from the beam-down solar concentrating system. The solar tests were performed in the middle of December, 2015. The central bed temperature of the receiver was reached around 960-1100° C. It was found that only 20 Ndm3/min of air flow rate was enough to create the uniform fluidization of the particles at the given temperature range. It was predicted that if the central bed temperature could have been higher than 1100°C if solar receiver test had conducted in other seasons than winter. The next solar campaign of the receiver test will be carried out in October, 2016.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
Particles fluidized bed receiver/reactor tests with quartz sand particles using a 100-kWth beam-down solar concentrating system at Miyazaki
A window-type, solar fluidized bed receiver with quartz sand particles was tested by a 100-kWth novel beam-down solar concentrating system at Miyazaki, Japan. A compound parabolic concentrator (CPC) was placed above the quartz window of the receiver to increase the concentration of the solar fluxes from the beam-down solar concentrating system. The solar tests were performed in the middle of December, 2015. The central bed temperature of the receiver was reached around 960-1100° C. It was found that only 20 Ndm3/min of air flow rate was enough to create the uniform fluidization of the particles at the given temperature range. It was predicted that if the central bed temperature could have been higher than 1100°C if solar receiver test had conducted in other seasons than winter. The next solar campaign of the receiver test will be carried out in October, 2016.
- Open Access
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1734 (1) , 120004
Particles fluidized bed receiver/reactor with a beam-down solar concentrating optics: 30-kWth performance test using a big sun-simulator
A novel concept of particles fluidized bed receiver/reactor with a beam-down solar concentrating optics was performed using a 30-kWth window type receiver by a big sun-simulator. A fluidized bed of quartz sand particles was created by passing air from the bottom distributor of the receiver, and about 30 kWth of high flux visible light from 19 xenon-arc lamps of the sun-simulator was directly irradiated on the top of the fluidized bed in the receiver through a quartz window. The particle bed temperature at the center position of the fluidized bed went up to a temperature range from 1050 to 1200°C by the visible light irradiation with the average heat flux of about 950 kW/m2, depending on the air flow rate. The output air temperature from the receiver reached 1000 - 1060°C.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1734 (1) , 120004
Open AccessParticles fluidized bed receiver/reactor with a beam-down solar concentrating optics: 30-kWth performance test using a big sun-simulator
A novel concept of particles fluidized bed receiver/reactor with a beam-down solar concentrating optics was performed using a 30-kWth window type receiver by a big sun-simulator. A fluidized bed of quartz sand particles was created by passing air from the bottom distributor of the receiver, and about 30 kWth of high flux visible light from 19 xenon-arc lamps of the sun-simulator was directly irradiated on the top of the fluidized bed in the receiver through a quartz window. The particle bed temperature at the center position of the fluidized bed went up to a temperature range from 1050 to 1200°C by the visible light irradiation with the average heat flux of about 950 kW/m2, depending on the air flow rate. The output air temperature from the receiver reached 1000 - 1060°C.
- 1 January 2015
- Published by The Japan Institute of Energy in Journal of the Japan Institute of Energy
- Vol. 94 (11) , 1323-1329
Laboratory Experiment and Simulation of High-temperature Fluidized Bed Air Receiver for Concentrated Solar Power Generation
This study proposes a two-tower type fluidized receiver for receiving concentrated solar light at high temperatures is proposed. This fluidized receiver is coupled with the Miyazaki beam-down reflector system. The visualization and the numerical simulation was made for the laboratory model to show the fluid-dynamics and the heat transport as well as to elaborate the existing demonstration model. The experimental visualization of the cold model demonstrated that in each tower, the particles are moved by the aerated organized flow. The numerical simulation was made using the thermal input cited from the 5.0kWth sun simulator. The numerical simulation demonstrated that the inner particles are heated above 950 °C after 3.0 minutes of the aeration start time. The increase in temperature is caused by the intrusion of the heated particles from the high-pressure side tower to the low-pressure side tower. It is thus suggested that collective circulation occurs between high- and low-pressure side towers and this can be utilized for a direct thermal storage system.
- 1 January 2015
- Published by The Japan Institute of Energy in Journal of the Japan Institute of Energy
- Vol. 94 (11) , 1323-1329
Laboratory Experiment and Simulation of High-temperature Fluidized Bed Air Receiver for Concentrated Solar Power Generation
This study proposes a two-tower type fluidized receiver for receiving concentrated solar light at high temperatures is proposed. This fluidized receiver is coupled with the Miyazaki beam-down reflector system. The visualization and the numerical simulation was made for the laboratory model to show the fluid-dynamics and the heat transport as well as to elaborate the existing demonstration model. The experimental visualization of the cold model demonstrated that in each tower, the particles are moved by the aerated organized flow. The numerical simulation was made using the thermal input cited from the 5.0kWth sun simulator. The numerical simulation demonstrated that the inner particles are heated above 950 °C after 3.0 minutes of the aeration start time. The increase in temperature is caused by the intrusion of the heated particles from the high-pressure side tower to the low-pressure side tower. It is thus suggested that collective circulation occurs between high- and low-pressure side towers and this can be utilized for a direct thermal storage system.