Tolga Yasa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Tolga Yasa has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Guillermo Paniagua
Zucrow Laboratories, Purdue University, 500 Allison Road, West Lafayette, IN 47907, USA
19 shared publications S. Lavagnoli
Von Karman Institute for Fluid Dynamics, Rhode Saint Genèse, Belgium
4 shared publicationsGlauco Bonfanti
2 shared publicationsIsa Kavas
METU Aerospace Engineering Department
2 shared publications- Juan Pedro Solano
Departamento de Ingeniería Térmica y de Fluidos, Universidad Politécnica de Cartagena, Cartagena, Spain
2 shared publications - Kürşad Melih Güleren
Eskişehir Osmangazi Üniversitesi
2 shared publications
Latest Publications
- Open Access
- 3 June 2024
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 44 (1) , 33-45
DÖNEN PATLAMA MOTORLARINDAKİ OLUŞAN DALGA YAPISININ SAYISAL OLARAK İNCELENMESİ
Bu çalışmada dönen patlama motorundaki patlama dalgası yapısı ve itki performansı sayısal olarak incelenmiştir. Sayısal çalışmalar iki aşamada gerçekleştirilmiştir. İlk olarak deneysel ve sayısal verilerin yer aldığı referans çalışmaya yönelik doğrulama çalışmaları tamamlanmıştır. Deneysel çalışmalarda hidrojen 0.8 mm çapındaki 90 enjektörden, hava ise 0.4 mm genişliğindeki aralıktan patlama kanalına aktarılmaktadır. Referans sayısal çalışmada yer verildiği üzere tek basamaklı tersinmez hidrojen-hava mekanizması doğrulama çalışmalarında kullanılmıştır. Doğrulama analizleri sonrasında patlama dalgasının detaylı olarak incelenebilmesi için 19 basamaklı tersinmez hidrojen-hava reaksiyon mekanizması sayısal çalışmalara tanımlanmıştır. Sayısal çalışmalarda daimi olmayan yoğunluğa dayalı çözücü kullanılmıştır. İkinci aşamada patlama dalga yapısı ve dönen patlama motorunun itki performansı araştırılmıştır. Sonuç olarak patlama dalgasının 1.1 ms sonrasında kararlı yapıya ulaşabildiği belirlenmiştir. Değişen blokaj oranı nedeniyle t=1.1 ms öncesinde patlama dalgası yüksekliği sabit kalmamıştır. Kararlı patlama dalgası yüksekliğinin tek basamaklı ve 19 basamaklı çalışmalarında sırasıyla 29 mm ve 27 mm olduğu tespit edilmiştir. Patlama kanalı çıkışındaki itki dağılımının kararlı patlama dalgası ile neredeyse sabit olduğu belirlenmiş ve itki değerinde 678.7±2.3 N aralığında salınımların meydana geldiği gözlemlenmiştir.
- 3 June 2024
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 44 (1) , 33-45
Open AccessDÖNEN PATLAMA MOTORLARINDAKİ OLUŞAN DALGA YAPISININ SAYISAL OLARAK İNCELENMESİ
Bu çalışmada dönen patlama motorundaki patlama dalgası yapısı ve itki performansı sayısal olarak incelenmiştir. Sayısal çalışmalar iki aşamada gerçekleştirilmiştir. İlk olarak deneysel ve sayısal verilerin yer aldığı referans çalışmaya yönelik doğrulama çalışmaları tamamlanmıştır. Deneysel çalışmalarda hidrojen 0.8 mm çapındaki 90 enjektörden, hava ise 0.4 mm genişliğindeki aralıktan patlama kanalına aktarılmaktadır. Referans sayısal çalışmada yer verildiği üzere tek basamaklı tersinmez hidrojen-hava mekanizması doğrulama çalışmalarında kullanılmıştır. Doğrulama analizleri sonrasında patlama dalgasının detaylı olarak incelenebilmesi için 19 basamaklı tersinmez hidrojen-hava reaksiyon mekanizması sayısal çalışmalara tanımlanmıştır. Sayısal çalışmalarda daimi olmayan yoğunluğa dayalı çözücü kullanılmıştır. İkinci aşamada patlama dalga yapısı ve dönen patlama motorunun itki performansı araştırılmıştır. Sonuç olarak patlama dalgasının 1.1 ms sonrasında kararlı yapıya ulaşabildiği belirlenmiştir. Değişen blokaj oranı nedeniyle t=1.1 ms öncesinde patlama dalgası yüksekliği sabit kalmamıştır. Kararlı patlama dalgası yüksekliğinin tek basamaklı ve 19 basamaklı çalışmalarında sırasıyla 29 mm ve 27 mm olduğu tespit edilmiştir. Patlama kanalı çıkışındaki itki dağılımının kararlı patlama dalgası ile neredeyse sabit olduğu belirlenmiş ve itki değerinde 678.7±2.3 N aralığında salınımların meydana geldiği gözlemlenmiştir.
- 31 October 2021
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 41 (2) , 205-226
TÜRBÜLANSLI YANMA İÇİN DÖNDÜRÜCÜNÜN PARAMETRİK ÇALIŞMASI
Bu çalışmada döndürücüye ait kanat sayısı, kanat sarım açısı ve kanat uzunluğu ile yakıt giriş çapının yanma odasındaki türbülanslı akış yapısı, yanma verimi ve emisyon değerleri üzerine etkisi araştırılmıştır. Referans alınan döndürücü kanat sayısı (n), kanat uzunluğu (L), kanat sarım açısı (θ) ve yakıt giriş çapı (D2) sırası ile 10, 40 mm, 45°, 19.5 mm’dir. Kanat sayısı (6,8,10,12,14), kanat uzunluğu (0.5L, L, 1.5L, 2L), kanat sarım açısı (30°, 45°, 60°, 75°, 90°, 120°) ve yakıt giriş çapı için (0.5 D2, D2, 1.5 D2, 2 D2) parametrik değerler kullanılarak yeni modeller oluşturulmuştur. Sayısal çalışmalar ANSYS/Fluent 17.2 ticari yazılımı ile gerçekleştirilmiş ve referans alınan deneysel çalışmaya uygun olarak önceden karışmamış yanma modeli tanımlanmıştır. Sayısal yöntem, elde edilen verilerin deneysel veriler ile karşılaştırılması ile doğrulanmıştır. Analizler sonucu olarak kanat sarım açısının alev şekli, kanat uzunluğunun ise alevin simetrik yapısı üzerine önemli etkisinin olduğu bulunmuştur. M04510403900 (θ=45°, n=10, L=40 mm, D2=39.00 mm) modelinde en yüksek ısıl verim elde edilmiş ve % 79.3 olan referans döndürücünün ısıl verimi bu model ile % 93.8’e yükselmiştir. Yanma odası seyreltme delikleri öncesinde CO kütle fraksiyonu değerinin referans döndürücü modelinde 0.002 olduğu ve M04510400975 (θ=45°, n=10, L=40 mm, D2=9.75 mm) modelinde bu değerin 0.018’e yükseldiği tespit edilmiştir.
- 31 October 2021
- Published by Turk Isi Bilimi Ve Teknigi Dernegi in Isı Bilimi ve Tekniği Dergisi
- Vol. 41 (2) , 205-226
TÜRBÜLANSLI YANMA İÇİN DÖNDÜRÜCÜNÜN PARAMETRİK ÇALIŞMASI
Bu çalışmada döndürücüye ait kanat sayısı, kanat sarım açısı ve kanat uzunluğu ile yakıt giriş çapının yanma odasındaki türbülanslı akış yapısı, yanma verimi ve emisyon değerleri üzerine etkisi araştırılmıştır. Referans alınan döndürücü kanat sayısı (n), kanat uzunluğu (L), kanat sarım açısı (θ) ve yakıt giriş çapı (D2) sırası ile 10, 40 mm, 45°, 19.5 mm’dir. Kanat sayısı (6,8,10,12,14), kanat uzunluğu (0.5L, L, 1.5L, 2L), kanat sarım açısı (30°, 45°, 60°, 75°, 90°, 120°) ve yakıt giriş çapı için (0.5 D2, D2, 1.5 D2, 2 D2) parametrik değerler kullanılarak yeni modeller oluşturulmuştur. Sayısal çalışmalar ANSYS/Fluent 17.2 ticari yazılımı ile gerçekleştirilmiş ve referans alınan deneysel çalışmaya uygun olarak önceden karışmamış yanma modeli tanımlanmıştır. Sayısal yöntem, elde edilen verilerin deneysel veriler ile karşılaştırılması ile doğrulanmıştır. Analizler sonucu olarak kanat sarım açısının alev şekli, kanat uzunluğunun ise alevin simetrik yapısı üzerine önemli etkisinin olduğu bulunmuştur. M04510403900 (θ=45°, n=10, L=40 mm, D2=39.00 mm) modelinde en yüksek ısıl verim elde edilmiş ve % 79.3 olan referans döndürücünün ısıl verimi bu model ile % 93.8’e yükselmiştir. Yanma odası seyreltme delikleri öncesinde CO kütle fraksiyonu değerinin referans döndürücü modelinde 0.002 olduğu ve M04510400975 (θ=45°, n=10, L=40 mm, D2=9.75 mm) modelinde bu değerin 0.018’e yükseldiği tespit edilmiştir.
- 9 November 2017
- Published by Springer Nature
- p. 139-158
Aerothermal Investigation of a Turbine Cooling Channel with U-Bend
- 9 November 2017
- Published by Springer Nature
- p. 139-158
Aerothermal Investigation of a Turbine Cooling Channel with U-Bend
- 6 March 2017
- Published by Emerald Publishing in Aircraft Engineering and Aerospace Technology
- Vol. 89 (2) , 203-210
Simulation-based steady-state aero-thermal model for small-scale turboprop engine
Purpose: An aircraft engine control system consists of a large scale of control parameters and variables because of the complex structure of aero-engine. Monitoring and adjusting control variables and parameters such as detecting, isolating and reconfiguring the system faults/failures depend on the controller design. Developing a robust controller is based on an accurate mathematical model. Design/methodology/approach: In this study, a small-scale turboprop engine is modeled. Simulation is carried out on MATLAB/Simulink for design and off-design operating conditions. Both steady-state and transient conditions (from idle to maximum thrust levels) are tested. The performance parameters of compressor and turbine components are predicted via trained Neuro-Fuzzy model (ANFIS) based on component maps. Temperature, rotational speed, mass flow, pressure and other parameters are generated by using thermodynamic formulas and conservation laws. Considering these calculated values, error calculations are made and compared with the cycle data of the engine at the related simulation conditions. Findings: Simulation results show that the designed engine model’s simulation values have acceptable accuracy for both design and off-design conditions from idle to maximum power operating envelope considering cycle data. The designed engine model can be adapted to other types of gas turbine engines. Originality/value: Different from other literature studies, in this work, a small-scale turboprop engine is modeled. Furthermore, for performance prediction of compressor and turbine components, ANFIS structure is applied.
- 6 March 2017
- Published by Emerald Publishing in Aircraft Engineering and Aerospace Technology
- Vol. 89 (2) , 203-210
Simulation-based steady-state aero-thermal model for small-scale turboprop engine
Purpose: An aircraft engine control system consists of a large scale of control parameters and variables because of the complex structure of aero-engine. Monitoring and adjusting control variables and parameters such as detecting, isolating and reconfiguring the system faults/failures depend on the controller design. Developing a robust controller is based on an accurate mathematical model. Design/methodology/approach: In this study, a small-scale turboprop engine is modeled. Simulation is carried out on MATLAB/Simulink for design and off-design operating conditions. Both steady-state and transient conditions (from idle to maximum thrust levels) are tested. The performance parameters of compressor and turbine components are predicted via trained Neuro-Fuzzy model (ANFIS) based on component maps. Temperature, rotational speed, mass flow, pressure and other parameters are generated by using thermodynamic formulas and conservation laws. Considering these calculated values, error calculations are made and compared with the cycle data of the engine at the related simulation conditions. Findings: Simulation results show that the designed engine model’s simulation values have acceptable accuracy for both design and off-design conditions from idle to maximum power operating envelope considering cycle data. The designed engine model can be adapted to other types of gas turbine engines. Originality/value: Different from other literature studies, in this work, a small-scale turboprop engine is modeled. Furthermore, for performance prediction of compressor and turbine components, ANFIS structure is applied.
- 21 July 2016
- Published by Springer Nature
- p. 351-361
Flow Field Investigation of Rib-Roughened Serpentine Channel
- 21 July 2016
- Published by Springer Nature
- p. 351-361
Flow Field Investigation of Rib-Roughened Serpentine Channel
- 1 March 2015
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 223, 31-39
Local surface shear stress measurements from oil streaks thinning rate
- 1 March 2015
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 223, 31-39
Local surface shear stress measurements from oil streaks thinning rate
- 25 March 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 135 (3) , 031027
Analysis of the Unsteady Overtip Casing Heat Transfer in a High Speed Turbine
In modern gas turbine engines, the rotor casing is vulnerable to thermal failures due to large unsteady heat fluxes. The rotor tip flow unsteadiness is induced by the periodic passage of the rotor blades, with an intensity dependent on the tip gap geometry. Hence, the understanding of the physics is of paramount importance to develop appropriate predictive tools and improve the cooling schemes. The present research aims at providing essential information on the flow conditions, which should serve to assess the relative impact of the overtip flow, tip gap magnitude, and work extraction processes on the casing thermal load. This paper presents simultaneous measurements of steady and unsteady heat transfer, pressure and rotor tip clearance in the casing of a transonic turbine stage. The research article was tested in a compression tube facility operating at engine representative conditions (vane Mach number 1.07, vane outlet Reynolds number 1.3 × 106, pressure ratio is 2.92, at 6790 rpm). The rotor blade geometry has a flat tip with a nominal tip clearance of about 0.4% of blade height. The heat transfer, pressure, and tip clearance data were obtained at three circumferential positions around the turbine casing. The heat flux was monitored using a single-layered thin film gauge able to resolve with high fidelity the wall temperature fluctuations. The heat flux sensor was mounted on a probe equipped with a heating device that allows varying the wall temperature. A series of experiments was performed at different heating rates to derive the local adiabatic wall temperature and the adiabatic convective heat transfer coefficient. A high bandwidth capacitive sensor provided the instantaneous value of the single blade tip clearance. A simple zero-dimensional model has been proved effective to predict the local flow temperature while the rotor spins up prior to the test, and estimate the overtip flow temperature during a test.
- 25 March 2013
- Published by Wiley in Journal of Turbomachinery
- Vol. 135 (3) , 031027
Analysis of the Unsteady Overtip Casing Heat Transfer in a High Speed Turbine
In modern gas turbine engines, the rotor casing is vulnerable to thermal failures due to large unsteady heat fluxes. The rotor tip flow unsteadiness is induced by the periodic passage of the rotor blades, with an intensity dependent on the tip gap geometry. Hence, the understanding of the physics is of paramount importance to develop appropriate predictive tools and improve the cooling schemes. The present research aims at providing essential information on the flow conditions, which should serve to assess the relative impact of the overtip flow, tip gap magnitude, and work extraction processes on the casing thermal load. This paper presents simultaneous measurements of steady and unsteady heat transfer, pressure and rotor tip clearance in the casing of a transonic turbine stage. The research article was tested in a compression tube facility operating at engine representative conditions (vane Mach number 1.07, vane outlet Reynolds number 1.3 × 106, pressure ratio is 2.92, at 6790 rpm). The rotor blade geometry has a flat tip with a nominal tip clearance of about 0.4% of blade height. The heat transfer, pressure, and tip clearance data were obtained at three circumferential positions around the turbine casing. The heat flux was monitored using a single-layered thin film gauge able to resolve with high fidelity the wall temperature fluctuations. The heat flux sensor was mounted on a probe equipped with a heating device that allows varying the wall temperature. A series of experiments was performed at different heating rates to derive the local adiabatic wall temperature and the adiabatic convective heat transfer coefficient. A high bandwidth capacitive sensor provided the instantaneous value of the single blade tip clearance. A simple zero-dimensional model has been proved effective to predict the local flow temperature while the rotor spins up prior to the test, and estimate the overtip flow temperature during a test.
- 1 December 2012
- Published by Elsevier in Applied Thermal Engineering
- Vol. 48, 1-10
Trailing edge shock modulation by pulsating coolant ejection
- 1 December 2012
- Published by Elsevier in Applied Thermal Engineering
- Vol. 48, 1-10
Trailing edge shock modulation by pulsating coolant ejection
- 1 August 2012
- Published by Elsevier in Flow Measurement and Instrumentation
- Vol. 26, 46-54
Robust procedure for multi-hole probe data processing
- 1 August 2012
- Published by Elsevier in Flow Measurement and Instrumentation
- Vol. 26, 46-54
Robust procedure for multi-hole probe data processing
- 11 June 2012
- Published by ASME International
- p. 573-587
Analysis of the Unsteady Overtip Casing Heat Transfer in a High Speed Turbine
In modern gas turbine engines, the rotor casing is vulnerable to thermal failures due to large unsteady heat fluxes. The rotor tip flow unsteadiness is induced by the periodic passage of the rotor blades, with an intensity dependent on the tip gap geometry. Hence, the understanding of the physics is of paramount importance to develop appropriate predictive tools and improve the cooling schemes. The present research aims at providing essential information on the flow conditions, which should serve to assess the relative impact of the overtip flow, tip gap magnitude and work extraction processes on the casing thermal load. This paper presents simultaneous measurements of steady and unsteady heat transfer, pressure and rotor tip clearance in the casing of a transonic turbine stage. The research article was tested in a compression tube facility operating at engine representative conditions (vane Mach number 1.07, vane outlet Reynolds number 1.3×106, pressure ratio is 2.92, at 6790 RPM). The rotor blade geometry has a flat tip with a nominal tip clearance of about 0.4% of blade height. The heat transfer, pressure, and tip clearance data were obtained at three circumferential positions around the turbine casing. The heat flux was monitored using a single-layered thin film gauge able to resolve with high-fidelity the wall temperature fluctuations. The heat flux sensor was mounted on a probe equipped with a heating device that allows varying the wall temperature. A series of experiments was performed at different heating rates to derive the local adiabatic wall temperature and the adiabatic convective heat transfer coefficient. A high bandwidth capacitive sensor provided the instantaneous value of the single blade tip clearance. A simple zero-dimensional model has been proved effective to predict the local flow temperature while the rotor spins up prior to the test, and estimate the overtip flow temperature during a test.
- 11 June 2012
- Published by ASME International
- p. 573-587
Analysis of the Unsteady Overtip Casing Heat Transfer in a High Speed Turbine
In modern gas turbine engines, the rotor casing is vulnerable to thermal failures due to large unsteady heat fluxes. The rotor tip flow unsteadiness is induced by the periodic passage of the rotor blades, with an intensity dependent on the tip gap geometry. Hence, the understanding of the physics is of paramount importance to develop appropriate predictive tools and improve the cooling schemes. The present research aims at providing essential information on the flow conditions, which should serve to assess the relative impact of the overtip flow, tip gap magnitude and work extraction processes on the casing thermal load. This paper presents simultaneous measurements of steady and unsteady heat transfer, pressure and rotor tip clearance in the casing of a transonic turbine stage. The research article was tested in a compression tube facility operating at engine representative conditions (vane Mach number 1.07, vane outlet Reynolds number 1.3×106, pressure ratio is 2.92, at 6790 RPM). The rotor blade geometry has a flat tip with a nominal tip clearance of about 0.4% of blade height. The heat transfer, pressure, and tip clearance data were obtained at three circumferential positions around the turbine casing. The heat flux was monitored using a single-layered thin film gauge able to resolve with high-fidelity the wall temperature fluctuations. The heat flux sensor was mounted on a probe equipped with a heating device that allows varying the wall temperature. A series of experiments was performed at different heating rates to derive the local adiabatic wall temperature and the adiabatic convective heat transfer coefficient. A high bandwidth capacitive sensor provided the instantaneous value of the single blade tip clearance. A simple zero-dimensional model has been proved effective to predict the local flow temperature while the rotor spins up prior to the test, and estimate the overtip flow temperature during a test.