Umberto Montanaro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Umberto Montanaro has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Alessandro di Gaeta
Consiglio Nazionale delle Ricerche
4 shared publications - Stefania Santini
University of Naples Federico II
3 shared publications - Josep Olm Miras
Institute of Industrial and Control Engineering, Universitat Politècnica de Catalunya, Barcelona, Spain
2 shared publications - Mario di Bernardo
Department of Electrical Engineering and Information Technologies, University of Naples Federico II, Naples, Italy
2 shared publications - Veniero Giglio
Istituto Motori
2 shared publications - Alejandro Rincón
Grupo de Investigación en Desarrollos Tecnológicos y Ambientales—GIDTA, Facultad de Ingeniería y Arquitectura, Universidad Católica de Manizales, Carrera 23 No. 60-63, Manizales 170002, Colombia
1 shared publication
Latest Publications
- 12 September 2014
- Published by Wiley in Asian Journal of Control
- Vol. 17 (5) , 1707-1724
Cycle‐by‐Cycle Adaptive Force Compensation for the Soft‐Landing Control of an Electro‐Mechanical Engine Valve Actuator
Electro‐mechanical valve actuators (EMVA) are a solution for implementing variable valve actuation in internal combustion engines. Their use can increase engine power, reduce fuel consumption and pollutant emissions, while significantly improving engine efficiency. The control of this actuator is a complex task since non‐smooth nonlinearities, parameter variations and external forces strongly affect plant dynamics. In addition, the impact of the valve at its end‐strokes translates into mechanical wear and unacceptable noise, and in the worst case the electromagnet may also fail to catch the valve, causing system failure. The design of effective control strategies to ensure valve capture with low impact velocities is therefore essential for the correct functioning of such a mechatronic device. In this paper, the control problem of reducing the impact velocity at “landing” known in the literature as soft landing control, is tackled via novel cycle‐by‐cycle adaptive force compensation control algorithms. Two schemes are presented: a discrete adaptive proportional integral controller to regulate landing velocity to a preassigned set‐point, and a gradient descent method based controller to automatically achieve the minimum admissible impact velocity. The effectiveness of both methods in limiting landing velocities is shown numerically using a high predictive simulator of the EMVA system, when considering unknown varying environmental conditions, such as internal friction and external gas pressure forces.
- 12 September 2014
- Published by Wiley in Asian Journal of Control
- Vol. 17 (5) , 1707-1724
Cycle‐by‐Cycle Adaptive Force Compensation for the Soft‐Landing Control of an Electro‐Mechanical Engine Valve Actuator
Electro‐mechanical valve actuators (EMVA) are a solution for implementing variable valve actuation in internal combustion engines. Their use can increase engine power, reduce fuel consumption and pollutant emissions, while significantly improving engine efficiency. The control of this actuator is a complex task since non‐smooth nonlinearities, parameter variations and external forces strongly affect plant dynamics. In addition, the impact of the valve at its end‐strokes translates into mechanical wear and unacceptable noise, and in the worst case the electromagnet may also fail to catch the valve, causing system failure. The design of effective control strategies to ensure valve capture with low impact velocities is therefore essential for the correct functioning of such a mechatronic device. In this paper, the control problem of reducing the impact velocity at “landing” known in the literature as soft landing control, is tackled via novel cycle‐by‐cycle adaptive force compensation control algorithms. Two schemes are presented: a discrete adaptive proportional integral controller to regulate landing velocity to a preassigned set‐point, and a gradient descent method based controller to automatically achieve the minimum admissible impact velocity. The effectiveness of both methods in limiting landing velocities is shown numerically using a high predictive simulator of the EMVA system, when considering unknown varying environmental conditions, such as internal friction and external gas pressure forces.
- Open Access
- 24 February 2012
- Published by Wiley in International Journal of Robust and Nonlinear Control
- Vol. 23 (7) , 709-730
Model reference adaptive control of discrete‐time piecewise linear systems
SUMMARY: This article presents a switched model reference adaptive controller for discrete‐time piecewise linear systems. In the spirit of the work by Landau in the late seventies, proof of asymptotic stability of the closed‐loop error system is obtained, recasting its dynamics as a feedback system and showing the feedforward and the feedback paths are both passive. The challenge is that both paths can be piecewise linear. Numerical results show excellent performance of the proposed controller even in the face of sudden variations of the plant parameters. Copyright © 2012 John Wiley & Sons, Ltd.
- 24 February 2012
- Published by Wiley in International Journal of Robust and Nonlinear Control
- Vol. 23 (7) , 709-730
Open AccessModel reference adaptive control of discrete‐time piecewise linear systems
SUMMARY: This article presents a switched model reference adaptive controller for discrete‐time piecewise linear systems. In the spirit of the work by Landau in the late seventies, proof of asymptotic stability of the closed‐loop error system is obtained, recasting its dynamics as a feedback system and showing the feedforward and the feedback paths are both passive. The challenge is that both paths can be piecewise linear. Numerical results show excellent performance of the proposed controller even in the face of sudden variations of the plant parameters. Copyright © 2012 John Wiley & Sons, Ltd.
- 29 September 2011
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 133 (6) , 061006
Model-Based Control of the Air Fuel Ratio for Gasoline Direct Injection Engines via Advanced Co-Simulation: An Approach to Reduce the Development Cycle of Engine Control Systems
Nowadays, the precise control of the air fuel ratio (AFR) in spark ignition (SI) engines plays a crucial role in meeting the more and more restrictive standard emissions for the passenger cars and the fuel economy required by the automotive market as well. To attain this demanding goal, the development of an advanced AFR control strategy embedding highly predictive models becomes mandatory for the next generation of electronic control unit (ECU). Conversely, the adoption of more complex control strategies affects the development time of the ECU increasing the time-to-market of new engine models. In this paper to solve the AFR control problem for gasoline direct injection (GDI) and to speed up the design of the entire control system, a gain scheduling PI model-based control strategy is proposed. To this aim, AFR dynamics are modeled via a first order time delay system whose parameters vary strongly with the fresh air mass entering the cylinders. Nonlinear relations have been found to describe the behavior of model parameters in function of air mass. Closed loop performances, when this novel controller is nested in the control loop, are compared to those provided by the classical PI Ziegler–Nichols control action with respect to different cost functions. Model validation as well as the effectiveness of the control design are carried out by means of ECU-1D engine co-simulation environment for a wide range of engine working conditions. The combination in one integrated designing environment of control systems and virtual engine, simulated through high predictive commercial one dimensional code, becomes a high predictive tool for automotive control engineers and enables fast prototyping.
- 29 September 2011
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 133 (6) , 061006
Model-Based Control of the Air Fuel Ratio for Gasoline Direct Injection Engines via Advanced Co-Simulation: An Approach to Reduce the Development Cycle of Engine Control Systems
Nowadays, the precise control of the air fuel ratio (AFR) in spark ignition (SI) engines plays a crucial role in meeting the more and more restrictive standard emissions for the passenger cars and the fuel economy required by the automotive market as well. To attain this demanding goal, the development of an advanced AFR control strategy embedding highly predictive models becomes mandatory for the next generation of electronic control unit (ECU). Conversely, the adoption of more complex control strategies affects the development time of the ECU increasing the time-to-market of new engine models. In this paper to solve the AFR control problem for gasoline direct injection (GDI) and to speed up the design of the entire control system, a gain scheduling PI model-based control strategy is proposed. To this aim, AFR dynamics are modeled via a first order time delay system whose parameters vary strongly with the fresh air mass entering the cylinders. Nonlinear relations have been found to describe the behavior of model parameters in function of air mass. Closed loop performances, when this novel controller is nested in the control loop, are compared to those provided by the classical PI Ziegler–Nichols control action with respect to different cost functions. Model validation as well as the effectiveness of the control design are carried out by means of ECU-1D engine co-simulation environment for a wide range of engine working conditions. The combination in one integrated designing environment of control systems and virtual engine, simulated through high predictive commercial one dimensional code, becomes a high predictive tool for automotive control engineers and enables fast prototyping.
- 1 January 2011
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 44 (1) , 5064-5069
Discrete-Time MRAC with Minimal Controller Synthesis of an Electronic Throttle Body
- 1 January 2011
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 44 (1) , 5064-5069
Discrete-Time MRAC with Minimal Controller Synthesis of an Electronic Throttle Body
- 1 January 2011
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 44 (1) , 4173-4180
An MRAC Approach for Tracking and Ripple Attenuation of the Common Rail Pressure for GDI Engines
- 1 January 2011
- Published by Elsevier in IFAC Proceedings Volumes
- Vol. 44 (1) , 4173-4180
An MRAC Approach for Tracking and Ripple Attenuation of the Common Rail Pressure for GDI Engines