Jeong Sam Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jeong Sam Han has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Bo Sung Shin
Department of Optics and Mechatronics, Pusan National University, Busan, Republic of Korea
1 shared publication - Byung Man Kwak
Department of Mechanical Engineering, Korea Advance Institute of Science and Technology, Daejeon, Korea
1 shared publication - Claas Müller
University of Freiburg, Department of Microsystems Engineering, Laboratory for Process Technology, Georges-Koehler-Allee 103, 79110 Freiburg, Germany
1 shared publication - Dae-Sik Lee
Electronics and Telecommunications Research Institute (ETRI)
1 shared publication Doyoung Byun
Konkuk University
1 shared publicationHee Won Seo
Andong Natl Univ, Dept Mech Design Engn, Andong, South Korea
1 shared publication
Latest Publications
- 1 April 2018
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - A
- Vol. 42 (4) , 379-389
Assessment of Local Failure and Improvement of a Disc Holder in a Parallel Slide Gate Valve Using Elastic-Plastic Analysis
A parallel slide gate valve (PSGV) is a critical component in a combined cycle power plant. It is located between the heat recovery steam generator and the steam turbine. The PSGV acts as a stop, or shut-off valve, under high-temperature and -pressure operating conditions. Thus, its performance and structural integrity must be ensured during the valve design. Among the components of the PSGV, the disc holder is connected to a stem to open and close the valve by moving the valve disc vertically. In this paper, an elastic-plastic analysis and structural integrity evaluation of the disc holder is performed per the local failure assessment described in ASME B& PVC VIII-2, where the plastic strain calculated from the elastic-plastic stress analysis is used. Additionally, an improved design is suggested, based on the evaluation results, resulting in an enlarged stem thrust satisfying the required level of safety compared to the initial disc holder.
- 1 April 2018
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - A
- Vol. 42 (4) , 379-389
Assessment of Local Failure and Improvement of a Disc Holder in a Parallel Slide Gate Valve Using Elastic-Plastic Analysis
A parallel slide gate valve (PSGV) is a critical component in a combined cycle power plant. It is located between the heat recovery steam generator and the steam turbine. The PSGV acts as a stop, or shut-off valve, under high-temperature and -pressure operating conditions. Thus, its performance and structural integrity must be ensured during the valve design. Among the components of the PSGV, the disc holder is connected to a stem to open and close the valve by moving the valve disc vertically. In this paper, an elastic-plastic analysis and structural integrity evaluation of the disc holder is performed per the local failure assessment described in ASME B& PVC VIII-2, where the plastic strain calculated from the elastic-plastic stress analysis is used. Additionally, an improved design is suggested, based on the evaluation results, resulting in an enlarged stem thrust satisfying the required level of safety compared to the initial disc holder.
- 11 April 2012
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 26 (4) , 1115-1126
Efficient frequency response and its direct sensitivity analyses for large-size finite element models using Krylov subspace-based model order reduction
- 11 April 2012
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 26 (4) , 1115-1126
Efficient frequency response and its direct sensitivity analyses for large-size finite element models using Krylov subspace-based model order reduction
- 14 October 2009
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 23 (10) , 2694-2702
An efficient numerical solution for frequency response function of micromechanical resonator arrays
- 14 October 2009
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 23 (10) , 2694-2702
An efficient numerical solution for frequency response function of micromechanical resonator arrays
- 1 September 2009
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - A
- Vol. 33 (9) , 878-885
Frequency Response Analysis of Array-Type MEMS Resonators by Model Order Reduction Using Krylov Subspace Method
- 1 September 2009
- Published by The Korean Society of Mechanical Engineers in Transactions of the Korean Society of Mechanical Engineers - A
- Vol. 33 (9) , 878-885
Frequency Response Analysis of Array-Type MEMS Resonators by Model Order Reduction Using Krylov Subspace Method
- 1 November 2006
- Published by Wiley in Journal of Mechanical Design
- Vol. 129 (11) , 1198-1203
Design, Simulation, and Fabrication of a Quadstable Monolithic Mechanism With X- and Y-Directional Bistable Curved Beams
This paper demonstrates a novel quadstable monolithic mechanism (QsMM), which provides four stable equilibrium positions within its planar operation range. The QsMM has been realized from the use of both X- and Y-directional bistable structures, which utilize curved snapping beams. Two pairs of curved beams were attached to an inner frame in both X and Y directions to present an independent bistable behavior in the directions. It was found out that the design of the inner frame is crucial for the quadstability and dynamic responses of the mechanism. A millimeter-scale brass mechanism was actually fabricated by ultraprecision milling to test the quadstability and the force-displacement behavior. The prototype clearly demonstrates four distinct stable positions in its millimeter-scale operation range. The design concept, finite element simulation, fabrication, and experimental measurement of the proposed multistable mechanism have been presented. The mechanical multistability of the proposed QsMM can be utilized for multiple switching and optical networking applications, yielding low power consumption operations.
- 1 November 2006
- Published by Wiley in Journal of Mechanical Design
- Vol. 129 (11) , 1198-1203
Design, Simulation, and Fabrication of a Quadstable Monolithic Mechanism With X- and Y-Directional Bistable Curved Beams
This paper demonstrates a novel quadstable monolithic mechanism (QsMM), which provides four stable equilibrium positions within its planar operation range. The QsMM has been realized from the use of both X- and Y-directional bistable structures, which utilize curved snapping beams. Two pairs of curved beams were attached to an inner frame in both X and Y directions to present an independent bistable behavior in the directions. It was found out that the design of the inner frame is crucial for the quadstability and dynamic responses of the mechanism. A millimeter-scale brass mechanism was actually fabricated by ultraprecision milling to test the quadstability and the force-displacement behavior. The prototype clearly demonstrates four distinct stable positions in its millimeter-scale operation range. The design concept, finite element simulation, fabrication, and experimental measurement of the proposed multistable mechanism have been presented. The mechanical multistability of the proposed QsMM can be utilized for multiple switching and optical networking applications, yielding low power consumption operations.
- 9 June 2006
- Published by Wiley in ETRI Journal
- Vol. 28 (3) , 389-392
A Laterally-Driven Bistable Electromagnetic Microrelay
- 9 June 2006
- Published by Wiley in ETRI Journal
- Vol. 28 (3) , 389-392
A Laterally-Driven Bistable Electromagnetic Microrelay
- 17 October 2002
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 12 (6) , 939-947
Parametric study and optimization of a micro-optical switch with a laterally driven electromagnetic microactuator
- 17 October 2002
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 12 (6) , 939-947
Parametric study and optimization of a micro-optical switch with a laterally driven electromagnetic microactuator