Ana-Maria Popa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ana-Maria Popa has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Daniel Crespy
Department of Materials Science and Engineering School of Molecular Science and Engineering Vidyasirimedhi Institute of Science and Technology VISTEC Rayong Thailand
2 shared publications Harry Heinzelmann
Centre Suisse d’Electronique et de Microtechnique SA, Rue Jaquet Droz 1, CH-2000 Neuchâtel, Switzerland
2 shared publications- Jeffrey A. Hubbell
Departments of Chemical and Biomolecular Engineering and of Biomedical Engineering, New York University, New York, NY, USA, 11021
2 shared publications Andrey Turshatov
Max Planck Institute for Polymer Research, Ackermannweg 10, 55128 Mainz, Germany
1 shared publication- Katharina Landfester
Max Planck Institute for Polymer Research, Ackermannweg 10, 55128 Mainz, Germany
1 shared publication - Patrick Rupper
EMPA, Swiss Federal Laboratories for Materials Science and Technology, Laboratory for Advanced Fibers, Lerchenfeldstrasse 5, CH-9014 St. Gallen, Switzerland
1 shared publication
Latest Publications
- 21 December 2011
- Published by Wiley in Journal of Polymer Science Part A: Polymer Chemistry
- Vol. 50 (6) , 1043-1048
A straightforward synthesis of fluorescent and temperature‐responsive nanogels
- 21 December 2011
- Published by Wiley in Journal of Polymer Science Part A: Polymer Chemistry
- Vol. 50 (6) , 1043-1048
A straightforward synthesis of fluorescent and temperature‐responsive nanogels
- 28 September 2011
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry
- Vol. 21 (43) , 17392-17395
A new generation of ultralight thermochromic indicators based on temperature induced gas release
We present here a new generation of thermochromic composites that require a minimal amount of materials for a significant optical effect. Polymer nanofibers were loaded with azo initiators that release nitrogen upon heating, and were subsequently coated with a thin gold film. The local release of nitrogen gas was shown to change the local topography of the fibers, while keeping the fiber morphology intact. The optical properties of the non-wovens could be controlled by the heating time, the heating temperature and the initial thickness of the film.
- 28 September 2011
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry
- Vol. 21 (43) , 17392-17395
A new generation of ultralight thermochromic indicators based on temperature induced gas release
We present here a new generation of thermochromic composites that require a minimal amount of materials for a significant optical effect. Polymer nanofibers were loaded with azo initiators that release nitrogen upon heating, and were subsequently coated with a thin gold film. The local release of nitrogen gas was shown to change the local topography of the fibers, while keeping the fiber morphology intact. The optical properties of the non-wovens could be controlled by the heating time, the heating temperature and the initial thickness of the film.
- 7 September 2010
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 26 (19) , 15356-15365
Dynamic Perspective on the Function of Thermoresponsive Nanopores from in Situ AFM and ATR-IR Investigations
This article describes the morphological and chemical characterization of stimuli-responsive functionalized silicon surfaces provided in parallel by atomic force spectroscopy (AFM) and Fourier transform infrared spectroscopy (FT-IR) enhanced by the single-beam sample reference attenuated total reflection method (SBSR-ATR). The stimuli-responsive behavior of the surfaces was obtained by grafting-to in melt carboxyl-terminated poly-N-isopropylacryl amides (PNIPAAM) with different degree of polymerization (DP) on epoxide-functionalized silicon substrates. The unprecedented real time and in situ physicochemical insight into the temperature-triggered response of the densely packed superficial brushes allowed for the selection of a PNIPAAM with a specific DP as a suitable polymer for the fabrication of silicon membranes exhibiting switchable nanopores. The fabrication process combines the manufacture of nanoporous silicon surfaces and their subsequent chemical functionalization by the grafting-to in melt of the selected polymer. Then, relevant information was obtained in what concerns the chemical modifications behind the topographical changes that drive the functioning of PNIPAAM-based hybrid nanovalves as well as the timescale on which the opening and closing of the nanopores occur.
- 7 September 2010
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 26 (19) , 15356-15365
Dynamic Perspective on the Function of Thermoresponsive Nanopores from in Situ AFM and ATR-IR Investigations
This article describes the morphological and chemical characterization of stimuli-responsive functionalized silicon surfaces provided in parallel by atomic force spectroscopy (AFM) and Fourier transform infrared spectroscopy (FT-IR) enhanced by the single-beam sample reference attenuated total reflection method (SBSR-ATR). The stimuli-responsive behavior of the surfaces was obtained by grafting-to in melt carboxyl-terminated poly-N-isopropylacryl amides (PNIPAAM) with different degree of polymerization (DP) on epoxide-functionalized silicon substrates. The unprecedented real time and in situ physicochemical insight into the temperature-triggered response of the densely packed superficial brushes allowed for the selection of a PNIPAAM with a specific DP as a suitable polymer for the fabrication of silicon membranes exhibiting switchable nanopores. The fabrication process combines the manufacture of nanoporous silicon surfaces and their subsequent chemical functionalization by the grafting-to in melt of the selected polymer. Then, relevant information was obtained in what concerns the chemical modifications behind the topographical changes that drive the functioning of PNIPAAM-based hybrid nanovalves as well as the timescale on which the opening and closing of the nanopores occur.
- 30 October 2009
- Published by IOP Publishing in Nanotechnology
- Vol. 20 (48) , 485303
Fabrication of nanopore arrays and ultrathin silicon nitride membranes by block-copolymer-assisted lithography
Here we show a method for patterning a thin metal film using self-assembled block-copolymer micelles monolayers as a template. The obtained metallic mask is transferred by reactive ion etching in silicon oxide, silicon and silicon nitride substrates, thus fabricating arrays of hexagonally packed nanopores with tunable diameters, interspacing and aspect ratios. This technology is compatible with integration into a standard microtechnology sequence for wafer-scale fabrication of ultrathin silicon nitride nanoporous membranes with 80 nm mean pore diameter.
- 30 October 2009
- Published by IOP Publishing in Nanotechnology
- Vol. 20 (48) , 485303
Fabrication of nanopore arrays and ultrathin silicon nitride membranes by block-copolymer-assisted lithography
Here we show a method for patterning a thin metal film using self-assembled block-copolymer micelles monolayers as a template. The obtained metallic mask is transferred by reactive ion etching in silicon oxide, silicon and silicon nitride substrates, thus fabricating arrays of hexagonally packed nanopores with tunable diameters, interspacing and aspect ratios. This technology is compatible with integration into a standard microtechnology sequence for wafer-scale fabrication of ultrathin silicon nitride nanoporous membranes with 80 nm mean pore diameter.