Yuan-Ching Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuan-Ching Lin has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Jiun-Nan Chen
Department of Mechanical Engineering, National Taiwan University of Science and Technology, Taipei 10607, Taiwan
3 shared publicationsDar-Jen Pen
Department of Mechanical Engineering, National Taiwan University of Science and Technology, Taipei 10607, Taiwan
2 shared publicationsS.W. Wang
Department of Mechanical Engineering, National Taiwan University of Science and Technology, 43, Keelung Road, Section 4, Taipei 106, Taiwan, ROC
2 shared publicationsC.H. Kao
Department of Mechanical Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
1 shared publicationChung-Yen Wu
Department of Mechanical Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan, ROC
1 shared publication- Dar-Jen Pen
Intelligent Machinery Technology Center, Industrial Technology Research Institute, Taichung, Taiwan
1 shared publication
Latest Publications
- 7 February 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 236 (11) , 1443-1452
Amorphous silica glass nano-grooving behavior investigated using molecular dynamics method
This work uses molecular dynamics to simulate the grooving behavior of optical silica glass. The amorphous SiO2 (silica glass) was fabricated using a melting-quenching process, and the critical cut depth, and mechanism of the chip formation, were explored using a molecular dynamics simulation. The analytical results indicated that the tool edge radius affected the critical cut depth and roughness of the machined surface. A larger tool edge radius had a larger equivalent negative rake angle at the same depth of cut, causing a larger critical cut depth, while producing a smoother machined surface. In addition, the uncut chip thickness affected the tangential force and thrust force distribution weighting of the tool. The temperature field analysis revealed that a groove formed by the chip formation mechanism resulted in a higher workpiece temperature, causing the brittle material to exhibit ductile cutting behavior during the nanogrooving process. However, grooves formed by the scratching-indenting mechanism had a lower workpiece temperature.
- 7 February 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 236 (11) , 1443-1452
Amorphous silica glass nano-grooving behavior investigated using molecular dynamics method
This work uses molecular dynamics to simulate the grooving behavior of optical silica glass. The amorphous SiO2 (silica glass) was fabricated using a melting-quenching process, and the critical cut depth, and mechanism of the chip formation, were explored using a molecular dynamics simulation. The analytical results indicated that the tool edge radius affected the critical cut depth and roughness of the machined surface. A larger tool edge radius had a larger equivalent negative rake angle at the same depth of cut, causing a larger critical cut depth, while producing a smoother machined surface. In addition, the uncut chip thickness affected the tangential force and thrust force distribution weighting of the tool. The temperature field analysis revealed that a groove formed by the chip formation mechanism resulted in a higher workpiece temperature, causing the brittle material to exhibit ductile cutting behavior during the nanogrooving process. However, grooves formed by the scratching-indenting mechanism had a lower workpiece temperature.
- 6 January 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (5-6) , 3395-3405
Using atomic response time to explore the effect of strain rate on yielding behaviors of tensile Cu nanowire with the molecular dynamic method
- 6 January 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (5-6) , 3395-3405
Using atomic response time to explore the effect of strain rate on yielding behaviors of tensile Cu nanowire with the molecular dynamic method
- 7 July 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 109 (3-4) , 727-743
Atomic behavior of single-crystal Ti nanowire plastic deformation under high strain rate simple tension
- 7 July 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 109 (3-4) , 727-743
Atomic behavior of single-crystal Ti nanowire plastic deformation under high strain rate simple tension
- 16 August 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 89 (9-12) , 3207-3215
Effect of crystallographic orientation on single crystal copper nanogrooving behaviors by MD method
- 16 August 2016
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 89 (9-12) , 3207-3215
Effect of crystallographic orientation on single crystal copper nanogrooving behaviors by MD method
- 5 September 2013
- Published by Taylor & Francis in Molecular Physics
- Vol. 112 (8) , 1115-1122
Molecular dynamic simulation of stress evolution analysis in Cu nanowire under ultra-high strain-rate simple tension
This study analyses the behaviour of atoms associated with the propagation of stress waves in Cu nanowires (NWs) during uniaxial tensile deformation using molecular dynamic simulation. Maximum local stress (MLS) and virial stress (VS) methods are adopted to express dynamic stress in ⟨100⟩ Cu NWs under tension. Simulation results indicated that the VS method enhances the averaging effect at ultra-high strain rates (above 1010 s−1), leading to serious undervaluation of yield stress. However, the MLS method provides superior prediction results for the dynamic mechanical responses of NWs under tension at the ultra-high strain rate than does the VS. At a strain rate of 7 × 1010 s−1, the double-peak stress phenomenon was observed in the stress–strain curve using the MLS method. The response time (Trs) to wave propagation, observed at an ultra-high strain rate, is responsible for the accumulation of the elastic stress that is applied at the beginning of tensile loading in a short period, producing the first stress peak. Following plastic deformation, the encounter of the wavefronts with the reduced tensile stress causes the fully constructive interference effect in the middle of the tensile NWs, producing the second stress peak. The results explain the dynamic mechanical behaviour of NWs, contributing to future applications of subsonic manufacturing.
- 5 September 2013
- Published by Taylor & Francis in Molecular Physics
- Vol. 112 (8) , 1115-1122
Molecular dynamic simulation of stress evolution analysis in Cu nanowire under ultra-high strain-rate simple tension
This study analyses the behaviour of atoms associated with the propagation of stress waves in Cu nanowires (NWs) during uniaxial tensile deformation using molecular dynamic simulation. Maximum local stress (MLS) and virial stress (VS) methods are adopted to express dynamic stress in ⟨100⟩ Cu NWs under tension. Simulation results indicated that the VS method enhances the averaging effect at ultra-high strain rates (above 1010 s−1), leading to serious undervaluation of yield stress. However, the MLS method provides superior prediction results for the dynamic mechanical responses of NWs under tension at the ultra-high strain rate than does the VS. At a strain rate of 7 × 1010 s−1, the double-peak stress phenomenon was observed in the stress–strain curve using the MLS method. The response time (Trs) to wave propagation, observed at an ultra-high strain rate, is responsible for the accumulation of the elastic stress that is applied at the beginning of tensile loading in a short period, producing the first stress peak. Following plastic deformation, the encounter of the wavefronts with the reduced tensile stress causes the fully constructive interference effect in the middle of the tensile NWs, producing the second stress peak. The results explain the dynamic mechanical behaviour of NWs, contributing to future applications of subsonic manufacturing.
- 27 August 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 22 (12) , 3674-3683
Material Flow Tracking for Various Tool Geometries During the Friction Stir Spot Welding Process
- 27 August 2013
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 22 (12) , 3674-3683
Material Flow Tracking for Various Tool Geometries During the Friction Stir Spot Welding Process
- 8 July 2013
- Published by Taylor & Francis in Tribology Transactions
- Vol. 56 (6) , 997-1010
Tribological Performance of Engine Oil Blended with Various Diesel Fuels
In this study, petrodiesel (D100) and different concentrations of commercial biodiesels (B100, B50, B5) were blended with a commercial engine oil at a fixed volume ratio of 1:9 to investigate the tribological effect of the biodiesels on the antiwear performance of the engine oil. The antiwear performance of the blended oils was evaluated using a Plint TE77 reciprocating ball-on-flat tribometer at room temperature and 150°C. Results show that the antiwear performance of the engine oil blended with petrodiesel is worse than that of the other blended oils with biodiesels at both temperatures. At room temperature, the physical adsorption and local hydrodynamic effects of the blended oils dominate the tribological behavior; at 150°C, the biodiesel seems to promote the growth of a reaction film with the antiwear additives in engine oil and enhance the growth rate of chemical films. However, an excess concentration of biodiesels causes tribochemical wear, thus reducing antiwear performance.
- 8 July 2013
- Published by Taylor & Francis in Tribology Transactions
- Vol. 56 (6) , 997-1010
Tribological Performance of Engine Oil Blended with Various Diesel Fuels
In this study, petrodiesel (D100) and different concentrations of commercial biodiesels (B100, B50, B5) were blended with a commercial engine oil at a fixed volume ratio of 1:9 to investigate the tribological effect of the biodiesels on the antiwear performance of the engine oil. The antiwear performance of the blended oils was evaluated using a Plint TE77 reciprocating ball-on-flat tribometer at room temperature and 150°C. Results show that the antiwear performance of the engine oil blended with petrodiesel is worse than that of the other blended oils with biodiesels at both temperatures. At room temperature, the physical adsorption and local hydrodynamic effects of the blended oils dominate the tribological behavior; at 150°C, the biodiesel seems to promote the growth of a reaction film with the antiwear additives in engine oil and enhance the growth rate of chemical films. However, an excess concentration of biodiesels causes tribochemical wear, thus reducing antiwear performance.
- 13 July 2010
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 8 (2) , 247-253
Elucidation of microstructure and wear behaviors of Ti–6Al–4V cladding using tungsten boride powder by the GTAW method
- 13 July 2010
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 8 (2) , 247-253
Elucidation of microstructure and wear behaviors of Ti–6Al–4V cladding using tungsten boride powder by the GTAW method
- 31 March 2009
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 30 (9) , 3388-3394
Simple model of interfacial bonding strength in detachment of reinforcing phase from clad layer during run-in process
- 31 March 2009
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 30 (9) , 3388-3394
Simple model of interfacial bonding strength in detachment of reinforcing phase from clad layer during run-in process