Alan McAlpine
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Alan McAlpine has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Michael J. Kingan
Acoustics Research Centre, Department of Mechanical and Mechatronics Engineering, The University of Auckland, Auckland, New Zealand
2 shared publications Alex P. Daymond-King
University of Southampton Institute of Sound and Vibration Research Southampton SO17 1BJ, United Kingdom
1 shared publicationAndrew J. Kempton
Rolls–Royce plc, P.O. Box 31, Derby DE24 8BJ, United Kingdom
1 shared publicationB.J. Tester
Rolls–Royce plc, Derby, P.O. Box 31, DE24 8BJ, England, UK
1 shared publication- B.J. Tester
Institute of Sound and Vibration Research, University of Southampton, Highfield, Southampton SO17 1BJ, UK
1 shared publication - Christopher J. Powles
Univ Cent Lancashire, Sch Phys Sci & Comp, Preston PR1 2HE, Lancs, England
1 shared publication
Latest Publications
- 1 March 2017
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 141 (3) , 1653-1663
Fuselage boundary-layer refraction of fan tones radiated from an installed turbofan aero-engine
A distributed source model to predict fan tone noise levels of an installed turbofan aero-engine is extended to include the refraction effects caused by the fuselage boundary layer. The model is a simple representation of an installed turbofan, where fan tones are represented in terms of spinning modes radiated from a semi-infinite circular duct, and the aircraft's fuselage is represented by an infinitely long, rigid cylinder. The distributed source is a disk, formed by integrating infinitesimal volume sources located on the intake duct termination. The cylinder is located adjacent to the disk. There is uniform axial flow, aligned with the axis of the cylinder, everywhere except close to the cylinder where there is a constant thickness boundary layer. The aim is to predict the near-field acoustic pressure, and in particular, to predict the pressure on the cylindrical fuselage which is relevant to assess cabin noise. Thus no far-field approximations are included in the modelling. The effect of the boundary layer is quantified by calculating the area-averaged mean square pressure over the cylinder's surface with and without the boundary layer included in the prediction model. The sound propagation through the boundary layer is calculated by solving the Pridmore-Brown equation. Results from the theoretical method show that the boundary layer has a significant effect on the predicted sound pressure levels on the cylindrical fuselage, owing to sound radiation of fan tones from an installed turbofan aero-engine.
- 1 March 2017
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 141 (3) , 1653-1663
Fuselage boundary-layer refraction of fan tones radiated from an installed turbofan aero-engine
A distributed source model to predict fan tone noise levels of an installed turbofan aero-engine is extended to include the refraction effects caused by the fuselage boundary layer. The model is a simple representation of an installed turbofan, where fan tones are represented in terms of spinning modes radiated from a semi-infinite circular duct, and the aircraft's fuselage is represented by an infinitely long, rigid cylinder. The distributed source is a disk, formed by integrating infinitesimal volume sources located on the intake duct termination. The cylinder is located adjacent to the disk. There is uniform axial flow, aligned with the axis of the cylinder, everywhere except close to the cylinder where there is a constant thickness boundary layer. The aim is to predict the near-field acoustic pressure, and in particular, to predict the pressure on the cylindrical fuselage which is relevant to assess cabin noise. Thus no far-field approximations are included in the modelling. The effect of the boundary layer is quantified by calculating the area-averaged mean square pressure over the cylinder's surface with and without the boundary layer included in the prediction model. The sound propagation through the boundary layer is calculated by solving the Pridmore-Brown equation. Results from the theoretical method show that the boundary layer has a significant effect on the predicted sound pressure levels on the cylindrical fuselage, owing to sound radiation of fan tones from an installed turbofan aero-engine.
- 16 April 2013
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 332 (16) , 3806-3831
A weak-scattering model for turbine-tone haystacking
- 16 April 2013
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 332 (16) , 3806-3831
A weak-scattering model for turbine-tone haystacking
- 1 December 2012
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 132 (6) , 3637-3646
Sound radiation from a flanged inclined duct
A simple method to calculate sound radiation from a flanged inclined duct is presented. An inclined annular duct is terminated by a rigid vertical plane. The duct termination is representative of a scarfed exit. The concept of a scarfed duct has been examined in turbofan aero-engines as a means to, potentially, shield a portion of the radiated sound from being transmitted directly to the ground. The sound field inside the annular duct is expressed in terms of spinning modes. Exterior to the duct, the radiated sound field owing to each mode can be expressed in terms of its directivity pattern, which is found by evaluating an appropriate form of Rayleigh's integral. The asymmetry is shown to affect the amplitude of the principal lobe of the directivity pattern, and to alter the proportion of the sound power radiated up or down. The methodology detailed in this article provides a simple engineering approach to investigate the sound radiation for a three-dimensional problem.
- 1 December 2012
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 132 (6) , 3637-3646
Sound radiation from a flanged inclined duct
A simple method to calculate sound radiation from a flanged inclined duct is presented. An inclined annular duct is terminated by a rigid vertical plane. The duct termination is representative of a scarfed exit. The concept of a scarfed duct has been examined in turbofan aero-engines as a means to, potentially, shield a portion of the radiated sound from being transmitted directly to the ground. The sound field inside the annular duct is expressed in terms of spinning modes. Exterior to the duct, the radiated sound field owing to each mode can be expressed in terms of its directivity pattern, which is found by evaluating an appropriate form of Rayleigh's integral. The asymmetry is shown to affect the amplitude of the principal lobe of the directivity pattern, and to alter the proportion of the sound power radiated up or down. The methodology detailed in this article provides a simple engineering approach to investigate the sound radiation for a three-dimensional problem.
- 1 October 2012
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 331 (21) , 4609-4628
Aeroacoustics research in Europe: The CEAS-ASC report on 2011 highlights
- 1 October 2012
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 331 (21) , 4609-4628
Aeroacoustics research in Europe: The CEAS-ASC report on 2011 highlights
- 1 June 2012
- Published by SAGE Publications in International Journal of Aeroacoustics
- Vol. 11 (2) , 213-245
Far-Field Sound Radiation Due to an Installed Open Rotor
Future single rotation propeller and contra-rotating advanced open rotor concepts promise a significant fuel efficiency advantage over current generation turbofan engines. The development of rotors which produce a minimum level of noise is a critical technical issue which needs to be resolved in order for these concepts to become viable aircraft propulsors. Noise and emissions are subject to stringent legislative requirements, thus accurate models are required in order to predict the noise radiated from aircraft engines. In this article, the development of a theoretical model to predict noise levels of an installed open rotor is reported. First a canonical problem is examined: how to predict the pressure field produced by a rotating ring of point sources adjacent to a rigid cylinder. Analytic expressions for the far-field pressure from a rotating ring of single-frequency monopole and dipole point sources, located near an infinitely long rigid cylinder, immersed in a constant axial mean flow, are explicitly formulated. Illustrative results show how the far-field pressure is affected by varying the source rotational direction, source location and source radius. Next the solution of the canonical problem is utilized to formulate a more advanced model to predict the noise due to an installed open rotor. In this model, the rotor noise sources are represented by a distribution of rotating sources. The adjacent aircraft fuselage is modeled by the rigid cylinder, and the effect of the fuselage boundary layer and other steady distortions are neglected. Also neglected is the scattering from other surfaces such as the pylon, wing and centerbody. This distributed source model can be used to calculate the effect of scattering of open rotor noise by an adjacent cylindrical fuselage. The model can be used to calculate both rotor-alone tones and tones produced by periodic unsteady loading on the rotor blades. Practical examples are provided which show how the effect of blade rotational direction and propeller location relative to the fuselage affect the sound produced by the interaction of a pylon wake with a rotor in a pusher configuration.
- 1 June 2012
- Published by SAGE Publications in International Journal of Aeroacoustics
- Vol. 11 (2) , 213-245
Far-Field Sound Radiation Due to an Installed Open Rotor
Future single rotation propeller and contra-rotating advanced open rotor concepts promise a significant fuel efficiency advantage over current generation turbofan engines. The development of rotors which produce a minimum level of noise is a critical technical issue which needs to be resolved in order for these concepts to become viable aircraft propulsors. Noise and emissions are subject to stringent legislative requirements, thus accurate models are required in order to predict the noise radiated from aircraft engines. In this article, the development of a theoretical model to predict noise levels of an installed open rotor is reported. First a canonical problem is examined: how to predict the pressure field produced by a rotating ring of point sources adjacent to a rigid cylinder. Analytic expressions for the far-field pressure from a rotating ring of single-frequency monopole and dipole point sources, located near an infinitely long rigid cylinder, immersed in a constant axial mean flow, are explicitly formulated. Illustrative results show how the far-field pressure is affected by varying the source rotational direction, source location and source radius. Next the solution of the canonical problem is utilized to formulate a more advanced model to predict the noise due to an installed open rotor. In this model, the rotor noise sources are represented by a distribution of rotating sources. The adjacent aircraft fuselage is modeled by the rigid cylinder, and the effect of the fuselage boundary layer and other steady distortions are neglected. Also neglected is the scattering from other surfaces such as the pylon, wing and centerbody. This distributed source model can be used to calculate the effect of scattering of open rotor noise by an adjacent cylindrical fuselage. The model can be used to calculate both rotor-alone tones and tones produced by periodic unsteady loading on the rotor blades. Practical examples are provided which show how the effect of blade rotational direction and propeller location relative to the fuselage affect the sound produced by the interaction of a pylon wake with a rotor in a pusher configuration.
- 16 January 2007
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 302 (1-2) , 403-407
Calculation of modes in azimuthally non-uniform lined ducts with uniform flow
- 16 January 2007
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 302 (1-2) , 403-407
Calculation of modes in azimuthally non-uniform lined ducts with uniform flow
- 1 March 2006
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 290 (3-5) , 1202-1233
“Buzz-saw” noise: A comparison of measurement with prediction
- 1 March 2006
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 290 (3-5) , 1202-1233
“Buzz-saw” noise: A comparison of measurement with prediction
- 25 May 2003
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 265 (1) , 175-200
On the prediction of “buzz-saw” noise in acoustically lined aero-engine inlet ducts
- 25 May 2003
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 265 (1) , 175-200
On the prediction of “buzz-saw” noise in acoustically lined aero-engine inlet ducts