Hassan Sheikh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hassan Sheikh has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Ali Sharbati
Electroceramics Research Center, Malek Ashtar University of Technology, Shahin Shahr, Isfahan, Iran
1 shared publicationE. Paimozd
Malek Ashtar University of Technology
1 shared publicationEbrahim Paimozd
Materials Engineering Department, Malek Ashtar University of Technology, Shahin Shahr, Iran, P. O. Box 83145/115
1 shared publicationM. R. Dehnavi
Department of Materials Engineering, Malek-Ashtar University of Technology (MUT), Shahin Shahr, Esfahan, Iran
1 shared publication- Ramin Ebrahimi
Shiraz University
1 shared publication S. M. Hashemi
Malek Ashtar University of Technology
1 shared publication
Latest Publications
- 31 May 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (10) , 2651-2659
Hot Deformation Characteristics and Microstructure Evolution of an Al–Zn–Mg–Ni–Fe–Zr Alloy
- 31 May 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (10) , 2651-2659
Hot Deformation Characteristics and Microstructure Evolution of an Al–Zn–Mg–Ni–Fe–Zr Alloy
- 1 August 2016
- Published by Springer Nature in Journal of Materials Science
- Vol. 51 (22) , 10178-10190
Investigation on texture evolution during cyclic expansion–extrusion (CEE) technique using crystal plasticity finite element modeling
- 1 August 2016
- Published by Springer Nature in Journal of Materials Science
- Vol. 51 (22) , 10178-10190
Investigation on texture evolution during cyclic expansion–extrusion (CEE) technique using crystal plasticity finite element modeling
- 27 June 2011
- Published by Wiley
- p. 163-172
Characteristics of Superconducting YBCO Phase Formation through Auto Combustion Citrate‐Nitrate Sol‐Gel
- 27 June 2011
- Published by Wiley
- p. 163-172
Characteristics of Superconducting YBCO Phase Formation through Auto Combustion Citrate‐Nitrate Sol‐Gel
- 27 March 2010
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 19 (9) , 1264-1267
Investigation into Characteristics of Portevin-Le Chatelier Effect of an Al-Mg Alloy
- 27 March 2010
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 19 (9) , 1264-1267
Investigation into Characteristics of Portevin-Le Chatelier Effect of an Al-Mg Alloy
- 1 February 2010
- Published by Allerton Press in Russian Journal of Non-Ferrous Metals
- Vol. 51 (1) , 59-61
Work hardening of Duratherm 600 cobalt superalloy using repetitive corrugation and straightening process
In this paper, the effect of repetitive corrugation and straightening (RCS) process on hardness of Duratherm 600 superalloy has been investigated. To do so, the RCS was carried out until 25 cycles using multiple teeth corrugative setup that the rotation of sample with 90° between cycles was utilized. The results show that the increasing of cycle number enhances the value of hardness. Also, the microstructures of samples are an evidence of slipbands formation during RCS showing the applied strain on the material. As a result, the increasing of hardness can be attributed to formation of subgrains, LAGBs and hcp martensitic plates at large strains.
- 1 February 2010
- Published by Allerton Press in Russian Journal of Non-Ferrous Metals
- Vol. 51 (1) , 59-61
Work hardening of Duratherm 600 cobalt superalloy using repetitive corrugation and straightening process
In this paper, the effect of repetitive corrugation and straightening (RCS) process on hardness of Duratherm 600 superalloy has been investigated. To do so, the RCS was carried out until 25 cycles using multiple teeth corrugative setup that the rotation of sample with 90° between cycles was utilized. The results show that the increasing of cycle number enhances the value of hardness. Also, the microstructures of samples are an evidence of slipbands formation during RCS showing the applied strain on the material. As a result, the increasing of hardness can be attributed to formation of subgrains, LAGBs and hcp martensitic plates at large strains.