Hongping Zhu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hongping Zhu has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Shun Weng
School of Civil and Hydraulic Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
18 shared publications - Yong Xia
Department of Civil and Environmental Engineering, The Hong Kong Polytechnic University, Hong Kong, China
16 shared publications - Dansheng Wang
School of Civil and Hydraulic Engineering, Huazhong University of Science and Technology, Wuhan, China
4 shared publications - Demi Ai
School of Civil and Hydraulic Engineering, Huazhong University of Science and Technology, Wuhan, People’s Republic of China
4 shared publications - Wenai Shen
Associate Professor, School of Civil and Hydraulic Engineering, Huazhong Univ. of Science and Technology, Wuhan 430074, China. ORCID:
4 shared publications - Pin Zhou
School of Civil Engineering and Mechanics, Huazhong University of Science and Technology, Wuhan, 430074, China
2 shared publications
Latest Publications
- Open Access
- 12 September 2025
- Published by Association for Computing Machinery (ACM)
- p. 1724-1731
Copula-Conditional GAIN: A Vine Copula-Empowered Framework for High-Fidelity Imputation of Missing Geotechnical Parameters
- 12 September 2025
- Published by Association for Computing Machinery (ACM)
- p. 1724-1731
Open AccessCopula-Conditional GAIN: A Vine Copula-Empowered Framework for High-Fidelity Imputation of Missing Geotechnical Parameters
- 3 February 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (3) , 035001
Deep neural network for electromechanical impedance analysis and damage detection of laminated rubber bearings
Environmental factors and loads cause potential small cracks in the rubber layers of laminated bearings. Conventional methods for identifying structural damage based on global vibration characteristics are ineffective, and current nondestructive structural damage detection methods based on Piezoelectric ceramic lead Zirconate Titanate (PZT) cannot fully capture deep damage-sensitive features from PZT signals. This study proposes a novel deep learning approach using a convolutional neural network with residual connections to conduct raw electromechanical admittance analysis and automatically extract damage-sensitive features to identify minor cracks in laminated rubber bearings. Numerical models are used to generate a sufficient amount of PZT data under various damage conditions for training the deep neural network, which overcomes the sparsity of damage states in actual laminated rubber bearings. A transfer learning method based on a model fine-tuning strategy was adopted to address the feature differences between the numerical models and actual rubber bearing structure. The fine-tuned model could effectively identify the damage location of actual laminated rubber bearings. The proposed method does not require a complex data preprocessing process when analyzing PZT signals and has a relatively high accuracy in damage localization. The promising results from this work offer a potential paradigm for data-driven PZT signal analysis, which is an appealing approach for identifying minor damage in real-life laminated rubber bearings.
- 3 February 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (3) , 035001
Deep neural network for electromechanical impedance analysis and damage detection of laminated rubber bearings
Environmental factors and loads cause potential small cracks in the rubber layers of laminated bearings. Conventional methods for identifying structural damage based on global vibration characteristics are ineffective, and current nondestructive structural damage detection methods based on Piezoelectric ceramic lead Zirconate Titanate (PZT) cannot fully capture deep damage-sensitive features from PZT signals. This study proposes a novel deep learning approach using a convolutional neural network with residual connections to conduct raw electromechanical admittance analysis and automatically extract damage-sensitive features to identify minor cracks in laminated rubber bearings. Numerical models are used to generate a sufficient amount of PZT data under various damage conditions for training the deep neural network, which overcomes the sparsity of damage states in actual laminated rubber bearings. A transfer learning method based on a model fine-tuning strategy was adopted to address the feature differences between the numerical models and actual rubber bearing structure. The fine-tuned model could effectively identify the damage location of actual laminated rubber bearings. The proposed method does not require a complex data preprocessing process when analyzing PZT signals and has a relatively high accuracy in damage localization. The promising results from this work offer a potential paradigm for data-driven PZT signal analysis, which is an appealing approach for identifying minor damage in real-life laminated rubber bearings.
- Open Access
Thermal Hysteresis Effect and Its Compensation on Electro-Mechanical Impedance Monitoring of Concrete Structure Embedded with Piezoelectric Sensor
Piezoelectric (PZT) sensors employed in the electro-mechanical impedance/admittance (EMI/EMA) technique are vulnerable to temperature variations when applied to concrete structural health monitoring (SHM). However, in practice, the ambient temperature transmitted from the air or surface to the concrete inner part is time-dependent during its monitoring process, which inflicts a critical challenge to ensure accurate signal processing for PZT sensors embedded inside the concrete. This paper numerically and experimentally investigated the thermal hysteresis effect on EMA-based concrete structure monitoring via an embedded PZT sensor. In the numerical modeling, a 3D finite element model of a concrete cube embedded with a PZT sensor was generated, where thermal hysteresis in the concrete, adhesive coat, and sensor was fully incorporated by introducing a temperature gradient. In the experiment, an equal-sized concrete cube installed with a cement-embedded PZT (CEP) sensor was cast and heated for 180 min at four temperature regimes for EMA monitoring. Experimental results, as a cogent validation of the simulation, indicated that EMA characteristics were functionally correlated to the dual effect of both heat transfer and the temperature regime. Moreover, a new approach relying on the frequency/magnitude of the maximum resonance peak in the EMA spectrum was proposed to effectively compensate for the thermal hysteresis effect, which could be regarded as a promising alternative for future applications.
Open AccessThermal Hysteresis Effect and Its Compensation on Electro-Mechanical Impedance Monitoring of Concrete Structure Embedded with Piezoelectric Sensor
Piezoelectric (PZT) sensors employed in the electro-mechanical impedance/admittance (EMI/EMA) technique are vulnerable to temperature variations when applied to concrete structural health monitoring (SHM). However, in practice, the ambient temperature transmitted from the air or surface to the concrete inner part is time-dependent during its monitoring process, which inflicts a critical challenge to ensure accurate signal processing for PZT sensors embedded inside the concrete. This paper numerically and experimentally investigated the thermal hysteresis effect on EMA-based concrete structure monitoring via an embedded PZT sensor. In the numerical modeling, a 3D finite element model of a concrete cube embedded with a PZT sensor was generated, where thermal hysteresis in the concrete, adhesive coat, and sensor was fully incorporated by introducing a temperature gradient. In the experiment, an equal-sized concrete cube installed with a cement-embedded PZT (CEP) sensor was cast and heated for 180 min at four temperature regimes for EMA monitoring. Experimental results, as a cogent validation of the simulation, indicated that EMA characteristics were functionally correlated to the dual effect of both heat transfer and the temperature regime. Moreover, a new approach relying on the frequency/magnitude of the maximum resonance peak in the EMA spectrum was proposed to effectively compensate for the thermal hysteresis effect, which could be regarded as a promising alternative for future applications.
- 4 July 2023
- Published by Springer Nature
- p. 173-192
Dynamic Condensation for Eigensolutions and Eigensensitivities
- 4 July 2023
- Published by Springer Nature
- p. 173-192
Dynamic Condensation for Eigensolutions and Eigensensitivities
- 4 July 2023
- Published by Springer Nature
- p. 1-7
Introduction
- 4 July 2023
- Published by Springer Nature
- p. 253-263
Model Updating of Nonlinear Structures Using Substructuring Method
- 4 July 2023
- Published by Springer Nature
- p. 253-263
Model Updating of Nonlinear Structures Using Substructuring Method
- 4 July 2023
- Published by Springer Nature
- p. 211-224
Dynamic Condensation Approach to Finite Element Model Updating
- 4 July 2023
- Published by Springer Nature
- p. 211-224
Dynamic Condensation Approach to Finite Element Model Updating
- 4 July 2023
- Published by Springer Nature
- p. 103-121
Simultaneous Iterative Substructuring Method for Eigensolutions and Eigensensitivity
- 4 July 2023
- Published by Springer Nature
- p. 103-121
Simultaneous Iterative Substructuring Method for Eigensolutions and Eigensensitivity
- 4 July 2023
- Published by Springer Nature
- p. 227-252
Substructuring Method for Responses and Response Sensitivities of Nonlinear Systems
- 4 July 2023
- Published by Springer Nature
- p. 227-252
Substructuring Method for Responses and Response Sensitivities of Nonlinear Systems
- 4 July 2023
- Published by Springer Nature
- p. 143-153
Substructuring Method Considering Inertial Effects of Slave Modes in the Time Domain
- 4 July 2023
- Published by Springer Nature
- p. 143-153
Substructuring Method Considering Inertial Effects of Slave Modes in the Time Domain