Silviu Mihai Petrişor
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Silviu Mihai Petrişor has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Ghiţă Bârsan
“Nicolae Bălcescu” Land Forces Academy , Sibiu , Romania
4 shared publications - Adriana Savin
National Institute of Research and Development for Technical Physics
2 shared publications - Mariana Domnica Stanciu
Faculty of Mechanical Engineering, Transilvania University of Brașov, 29 Eroilor Blvd., 500036 Brașov, Romania
2 shared publications - Rozina Steigmann
Nondestructive Testing Department, National Institute of R&D for Technical Physics, 47 D. Mangeron Blvd., 700050 Iasi, Romania
2 shared publications - Alexandru-Marius Rizescu
“Nicolae Bălcescu” Land Forces Academy , Sibiu , Romania
1 shared publication - Diana Andreea Aniela Ioan
“Nicolae Bălcescu” Land Forces Academy, Department of Technical Sciences, 3-5 Revoluţiei Street, Sibiu, 550170, Romania
1 shared publication
Latest Publications
- Open Access
Complementary Methods for the Assessment of the Porosity of Laser Additive-Manufactured Titanium Alloy
The method of making parts through additive manufacturing (AM) is becoming more and more widespread due to the possibility of the direct manufacturing of components with complex geometries. However, the technology’s capacity is limited by the appearance of micro-cracks/discontinuities during the layer-by-layer thermal process. The ultrasonic (US) method is often applied to detect and estimate the location and size of discontinuities in the metallic parts obtained by AM as well as to identify local deterioration in structures. The Ti6Al4V (Ti64) alloy prepared by AM needed to acquire a high-quality densification if remarkable mechanical properties were to be pursued. Ultrasonic instruments employ a different type of scanning for the studied samples, resulting in extremely detailed images comparable to X-rays. Automated non-destructive testing with special algorithms is widely used in the industry today. In general, this means that there is a trend towards automation and data sharing in various technological and production sectors, including the use of intelligent systems at the initial stage of production that can exclude defective construction materials, prevent the spread of defective products, and identify the causes of certain instances of damage. Placing the non-destructive testing on a completely new basis will create the possibility for a broader analysis of the primary data and thus will contribute to the improvement of both inspection reliability and consistency of the results. The paper aims to present the C-scan method, using ultrasonic images in amplitude or time-of-flight to emphasize discontinuities of Ti64 samples realized by laser powder-bed fusion (L-PBF) technology. The analysis of US maps offers the possibility of information correlation, mainly as to flaws in certain areas, as well as distribution of a specific flaw in the volume of the sample (flaws and pores). Final users can import C-scan results as ASCII files for further processing and comparison with other methods of analysis (e.g., non-linear elastic wave spectroscopy (NEWS), multi-frequency eddy current, and computer tomography), leading to specific results. The precision of the flight time measurement ensures the possibility of estimating the types of discontinuities, including volumetric ones, offering immediate results of the inspection. In situ monitoring allows the detection, characterization, and prediction of defects, which is suitable for robotics. Detailing the level of discontinuities at a certain location is extremely valuable for making maintenance and management decisions.
Open AccessComplementary Methods for the Assessment of the Porosity of Laser Additive-Manufactured Titanium Alloy
The method of making parts through additive manufacturing (AM) is becoming more and more widespread due to the possibility of the direct manufacturing of components with complex geometries. However, the technology’s capacity is limited by the appearance of micro-cracks/discontinuities during the layer-by-layer thermal process. The ultrasonic (US) method is often applied to detect and estimate the location and size of discontinuities in the metallic parts obtained by AM as well as to identify local deterioration in structures. The Ti6Al4V (Ti64) alloy prepared by AM needed to acquire a high-quality densification if remarkable mechanical properties were to be pursued. Ultrasonic instruments employ a different type of scanning for the studied samples, resulting in extremely detailed images comparable to X-rays. Automated non-destructive testing with special algorithms is widely used in the industry today. In general, this means that there is a trend towards automation and data sharing in various technological and production sectors, including the use of intelligent systems at the initial stage of production that can exclude defective construction materials, prevent the spread of defective products, and identify the causes of certain instances of damage. Placing the non-destructive testing on a completely new basis will create the possibility for a broader analysis of the primary data and thus will contribute to the improvement of both inspection reliability and consistency of the results. The paper aims to present the C-scan method, using ultrasonic images in amplitude or time-of-flight to emphasize discontinuities of Ti64 samples realized by laser powder-bed fusion (L-PBF) technology. The analysis of US maps offers the possibility of information correlation, mainly as to flaws in certain areas, as well as distribution of a specific flaw in the volume of the sample (flaws and pores). Final users can import C-scan results as ASCII files for further processing and comparison with other methods of analysis (e.g., non-linear elastic wave spectroscopy (NEWS), multi-frequency eddy current, and computer tomography), leading to specific results. The precision of the flight time measurement ensures the possibility of estimating the types of discontinuities, including volumetric ones, offering immediate results of the inspection. In situ monitoring allows the detection, characterization, and prediction of defects, which is suitable for robotics. Detailing the level of discontinuities at a certain location is extremely valuable for making maintenance and management decisions.
- Open Access
Humanitarian Demining Serial-Tracked Robot: Design and Dynamic Modeling
The paper proposes an original mechanical structure of a serial-tracked robot, subject of national invention patent number RO132301, B1/2021, destinated for humanitarian demining operations: anti-personnel mine detection by using a detection device mounted on the bottom’s tracked platform, demining and clearing the land of exploded mines using a TRTTR robot structure. The dynamic model of the robot structure is determined and numerically validated. A novel approach based on the Lagrange formalism and mechanical design equations has been used in the calculus and selection of robot driving motors. The obtained results for robot translation modules are presented and analyzed.
Open AccessHumanitarian Demining Serial-Tracked Robot: Design and Dynamic Modeling
The paper proposes an original mechanical structure of a serial-tracked robot, subject of national invention patent number RO132301, B1/2021, destinated for humanitarian demining operations: anti-personnel mine detection by using a detection device mounted on the bottom’s tracked platform, demining and clearing the land of exploded mines using a TRTTR robot structure. The dynamic model of the robot structure is determined and numerically validated. A novel approach based on the Lagrange formalism and mechanical design equations has been used in the calculus and selection of robot driving motors. The obtained results for robot translation modules are presented and analyzed.
- Open Access
Multi-Criteria Evaluation of the Failure of CFRP Laminates for Frames in the Automotive Industry
Methods to predict the fracture of thin carbon fibre-reinforced polymers (CFRPs) under load are of great interest in the automotive industry. The manufacturing of composites involves a high risk of defect occurrence, and the identification of those that lead to failure increases the functional reliability and decreases costs. The performance of CFRPs can be significantly reduced in assembled structures containing stress concentrators. This paper presents a hybrid experimental–numerical method based on the Tsai–Hill criterion for behavior of thin CFRPs at complex loadings that can emphasize the threshold of stress by tracing the σ-τ envelope. Modified butterfly samples were made for shearing, traction, or shearing-with-traction tests in the weakened section by changing the angle of force application α. ANSYS simulations were used to determine the zones of maximum stress concentration. For thin CFRP samples tested with stacking sequences [0]8 and [(45/0)2]s, the main mechanical characteristics have been determined using a Dynamic Mechanical Analyzer (DMA) and ultrasound tests. A modified Arcan device (AD) was used to generate data in a biaxial stress state, leading to the characterization of the material as a whole. The generated failure envelope allows for the prediction of failure for other combinations of normal and shear stress, depending on the thickness of the laminations, the stacking order, the pretension of the fasteners, and the method used to produce the laminations. The experimental data using AD and the application of the Tsai–Hill criterion serve to the increase the safety of CFRP components.
Open AccessMulti-Criteria Evaluation of the Failure of CFRP Laminates for Frames in the Automotive Industry
Methods to predict the fracture of thin carbon fibre-reinforced polymers (CFRPs) under load are of great interest in the automotive industry. The manufacturing of composites involves a high risk of defect occurrence, and the identification of those that lead to failure increases the functional reliability and decreases costs. The performance of CFRPs can be significantly reduced in assembled structures containing stress concentrators. This paper presents a hybrid experimental–numerical method based on the Tsai–Hill criterion for behavior of thin CFRPs at complex loadings that can emphasize the threshold of stress by tracing the σ-τ envelope. Modified butterfly samples were made for shearing, traction, or shearing-with-traction tests in the weakened section by changing the angle of force application α. ANSYS simulations were used to determine the zones of maximum stress concentration. For thin CFRP samples tested with stacking sequences [0]8 and [(45/0)2]s, the main mechanical characteristics have been determined using a Dynamic Mechanical Analyzer (DMA) and ultrasound tests. A modified Arcan device (AD) was used to generate data in a biaxial stress state, leading to the characterization of the material as a whole. The generated failure envelope allows for the prediction of failure for other combinations of normal and shear stress, depending on the thickness of the laminations, the stacking order, the pretension of the fasteners, and the method used to produce the laminations. The experimental data using AD and the application of the Tsai–Hill criterion serve to the increase the safety of CFRP components.
- Open Access
- 29 November 2013
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 13 (1) , 37-38
Elements on the Concept and Design of a Tracked Mini Robot - “ROBO GENIU” - Destined for Special Applications
- 29 November 2013
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 13 (1) , 37-38
Open AccessElements on the Concept and Design of a Tracked Mini Robot - “ROBO GENIU” - Destined for Special Applications
- Open Access
- 3 December 2012
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 12 (1) , 41-42
Perspectives on Constructive and Functional Optimizing of a Serial Robot with Four Degrees of Freedom Destined for Special Applications
- 3 December 2012
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 12 (1) , 41-42
Open AccessPerspectives on Constructive and Functional Optimizing of a Serial Robot with Four Degrees of Freedom Destined for Special Applications
- Open Access
- 3 December 2012
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 12 (1) , 621-622
Using the Elements of Manufacturing Systems Management in the Calculation of the Implementation of a Serial-Modular Industrial Robot within a Flexible Work Cell Designed for Special Applications
- 3 December 2012
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 12 (1) , 621-622
Open AccessUsing the Elements of Manufacturing Systems Management in the Calculation of the Implementation of a Serial-Modular Industrial Robot within a Flexible Work Cell Designed for Special Applications
- Open Access
- 9 December 2011
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 11 (1) , 279-280
Aspects on the Functional Optimization of an Industrial Robot Structure Implemented in Military Logistical Activities
- 9 December 2011
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 11 (1) , 279-280
Open AccessAspects on the Functional Optimization of an Industrial Robot Structure Implemented in Military Logistical Activities
- Open Access
- 1 December 2009
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 9 (1) , 689-690
Economically study regarding modernizing of the final working of the car radiators through implementation of an articulated robot in a flexible manufacturing cell
- 1 December 2009
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 9 (1) , 689-690
Open AccessEconomically study regarding modernizing of the final working of the car radiators through implementation of an articulated robot in a flexible manufacturing cell
- Open Access
- 1 December 2009
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 9 (1) , 589-590
The contributions regarding the conception, designing, modelling and the implementation in a flexible cell of fabrication of a modular serial robot
- 1 December 2009
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 9 (1) , 589-590
Open AccessThe contributions regarding the conception, designing, modelling and the implementation in a flexible cell of fabrication of a modular serial robot
- Open Access
- 1 December 2008
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 8 (1) , 10323-10324
Aspects Regarding the Conception, Modeling and Implementation of an Articulated Robot in Space with Noises and Vibrations
- 1 December 2008
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 8 (1) , 10323-10324
Open AccessAspects Regarding the Conception, Modeling and Implementation of an Articulated Robot in Space with Noises and Vibrations