Iñigo Iturriza
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Iñigo Iturriza has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Alvaro Soliz
Departamento de Ingeniería en Metalurgia, Universidad de Atacama, Av. Copayapu 485, Copiapó 1530000, Chile
2 shared publications - Claudio Aguilar
Universidad Tecnica Federico Santa Maria
2 shared publications - Danny Guzmán
Departamento de Ingeniería en Metalurgia, Universidad de Atacama, Av. Copayapu 485, Copiapó 1530000, Chile
2 shared publications - Alexis Guzmán
Departamento de Ingeniería en Metalurgia, Universidad de Atacama, Copiapó 1531772, Chile
1 shared publication - Antonio Sivo
Department of Applied Science and Technology (DISAT), Polytechnic of Turin, Corso Duca degli Abruzzi 24, 10129 Turin, Italy
1 shared publication - Borja Elguezabal Lazcano
Ceit-Basque Research and Technology Alliance (BRTA), Manuel Lardizabal 15, 20018 Donostia-San Sebastián, Spain
1 shared publication
Latest Publications
- Open Access
Fabrication and Arc Erosion Behavior of Ag-SnO2-ZnO Electrical Contact Materials
This study investigated the synthesis of Ag-SnO2-ZnO by powder metallurgy methods and their subsequent electrical contact behavior. The pieces of Ag-SnO2-ZnO were prepared by ball milling and hot pressing. The arc erosion behavior of the material was evaluated using homemade equipment. The microstructure and phase evolution of the materials were investigated through X-ray diffraction, energy-dispersive spectroscopy and scanning electron microscopy. The results showed that, although the mass loss of the Ag-SnO2-ZnO composite (9.08 mg) during the electrical contact test was higher than that of the commercial Ag-CdO (1.42 mg), its electrical conductivity remained constant (26.9 ± 1.5% IACS). This fact would be related to the reaction of Zn2SnO4’s formation on the material’s surface via electric arc. This reaction would play an important role in controlling the surface segregation and subsequent loss of electrical conductivity of this type of composite, thus enabling the development of a new electrical contact material to replace the non-environmentally friendly Ag-CdO composite.
Open AccessFabrication and Arc Erosion Behavior of Ag-SnO2-ZnO Electrical Contact Materials
This study investigated the synthesis of Ag-SnO2-ZnO by powder metallurgy methods and their subsequent electrical contact behavior. The pieces of Ag-SnO2-ZnO were prepared by ball milling and hot pressing. The arc erosion behavior of the material was evaluated using homemade equipment. The microstructure and phase evolution of the materials were investigated through X-ray diffraction, energy-dispersive spectroscopy and scanning electron microscopy. The results showed that, although the mass loss of the Ag-SnO2-ZnO composite (9.08 mg) during the electrical contact test was higher than that of the commercial Ag-CdO (1.42 mg), its electrical conductivity remained constant (26.9 ± 1.5% IACS). This fact would be related to the reaction of Zn2SnO4’s formation on the material’s surface via electric arc. This reaction would play an important role in controlling the surface segregation and subsequent loss of electrical conductivity of this type of composite, thus enabling the development of a new electrical contact material to replace the non-environmentally friendly Ag-CdO composite.
- 17 April 2023
- Published by SAGE Publications in Powder Metallurgy
- Vol. 66 (4) , 279-280
Francisco ‘Paco’ Castro – obituary
Francisco R. Castro (Paco) was born in what at some point was the world’s largest city, Mexico City, which meant that the world was always going to appear small to him. He was born in the m...
- 17 April 2023
- Published by SAGE Publications in Powder Metallurgy
- Vol. 66 (4) , 279-280
Francisco ‘Paco’ Castro – obituary
Francisco R. Castro (Paco) was born in what at some point was the world’s largest city, Mexico City, which meant that the world was always going to appear small to him. He was born in the m...
- Open Access
Thermal Mass Effect on the Solution Cooling Rate and on HIPped Astroloy Component Properties
Astroloy is a Ni-based superalloy with high-volume fraction of γ′, which gives high temperature properties but reduces its forgeability. Therefore, powder metallurgy manufacturing processes such as Near Net Shape HIPping are the most suitable manufacturing technology for Astroloy. However, NNSHIP has its own drawbacks, such as the formation of prior particle boundaries (PPBs), which usually tend to decrease material mechanical properties. The detrimental effect of PPBs can be reduced by optimizing the entire HIP processing route. Conventional HIP cycles have very low cooling rates, especially in big components from industry, and thus a series of post-heat treatments must be applied in order to achieve desirable microstructures and improve the mechanical properties. Standard heat treatments for Astroloy are long and tedious with several steps of solutioning, stabilization and precipitation. In this work, two main studies have been performed. First, the effect of the cooling rate after the solutioning treatment, which is driven by the materials’ thermal mass, on the Astroloy microstructure and mechanical properties was studied. Experimental analyses and simulation techniques have been used in the present work and it has been found that higher cooling rates after solutioning increase the density of tertiary γ′ precipitates by 85%, and their size decreases by 22%, which leads to an increase in hardness from 356 to 372 HB30. This hardness difference tends to reduce after subsequent standard heat treatment (HT) that homogenizes the microstructure. The second study shows the effect of different heat treatments on the microstructure and hardness of samples with two different thermal masses (can and cube). More than double the density of γ′ precipitates was found in small cubes in comparison with cans with a higher thermal mass. Therefore, the hardness in cubes is between 4 and 20 HB 30 higher than in large cans, depending on the applied HT.
Open AccessThermal Mass Effect on the Solution Cooling Rate and on HIPped Astroloy Component Properties
Astroloy is a Ni-based superalloy with high-volume fraction of γ′, which gives high temperature properties but reduces its forgeability. Therefore, powder metallurgy manufacturing processes such as Near Net Shape HIPping are the most suitable manufacturing technology for Astroloy. However, NNSHIP has its own drawbacks, such as the formation of prior particle boundaries (PPBs), which usually tend to decrease material mechanical properties. The detrimental effect of PPBs can be reduced by optimizing the entire HIP processing route. Conventional HIP cycles have very low cooling rates, especially in big components from industry, and thus a series of post-heat treatments must be applied in order to achieve desirable microstructures and improve the mechanical properties. Standard heat treatments for Astroloy are long and tedious with several steps of solutioning, stabilization and precipitation. In this work, two main studies have been performed. First, the effect of the cooling rate after the solutioning treatment, which is driven by the materials’ thermal mass, on the Astroloy microstructure and mechanical properties was studied. Experimental analyses and simulation techniques have been used in the present work and it has been found that higher cooling rates after solutioning increase the density of tertiary γ′ precipitates by 85%, and their size decreases by 22%, which leads to an increase in hardness from 356 to 372 HB30. This hardness difference tends to reduce after subsequent standard heat treatment (HT) that homogenizes the microstructure. The second study shows the effect of different heat treatments on the microstructure and hardness of samples with two different thermal masses (can and cube). More than double the density of γ′ precipitates was found in small cubes in comparison with cans with a higher thermal mass. Therefore, the hardness in cubes is between 4 and 20 HB 30 higher than in large cans, depending on the applied HT.
- Open Access
Synthesis and Electrochemical Properties of Ti-Si Alloys Prepared by Mechanical Alloying and Heat Treatment
The aim of this work was to study the synthesis and electrochemical properties of Ti 2 wt %-Si alloys prepared by mechanical alloying (MA) and heat treatment. The MA process was performed under Ar atmosphere. The structural, morphological, and compositional evolutions during the milling and subsequent heat treatment were investigated by X-ray diffraction, energy-dispersive spectroscopy, and scanning electron microscopy. The electrochemical behavior was evaluated by open circuit potential and linear sweep voltammetry measurements. The results showed that the MA process promotes the formation of a supersaturated α-Ti-Si solid solution. During heat treatment, the Si remaining in the mechanically alloyed powders and the Si from the α-Ti-Si supersaturated solid solution reacted with Ti to form Ti-Si intermetallic compounds. These compounds have a fine and homogeneous distribution in the α-Ti matrix, which cannot be achieved by conventional casting methods. Additionally, the electrochemical evaluations revealed that the mechanically alloyed and heat-treated Ti 2 wt %-Si powders have better corrosion resistance in 1.63 M H2SO4 than the pure Ti and MA Ti-Si samples. This is likely due to the particular microstructure produced during the milling and subsequent heat treatment.
Open AccessSynthesis and Electrochemical Properties of Ti-Si Alloys Prepared by Mechanical Alloying and Heat Treatment
The aim of this work was to study the synthesis and electrochemical properties of Ti 2 wt %-Si alloys prepared by mechanical alloying (MA) and heat treatment. The MA process was performed under Ar atmosphere. The structural, morphological, and compositional evolutions during the milling and subsequent heat treatment were investigated by X-ray diffraction, energy-dispersive spectroscopy, and scanning electron microscopy. The electrochemical behavior was evaluated by open circuit potential and linear sweep voltammetry measurements. The results showed that the MA process promotes the formation of a supersaturated α-Ti-Si solid solution. During heat treatment, the Si remaining in the mechanically alloyed powders and the Si from the α-Ti-Si supersaturated solid solution reacted with Ti to form Ti-Si intermetallic compounds. These compounds have a fine and homogeneous distribution in the α-Ti matrix, which cannot be achieved by conventional casting methods. Additionally, the electrochemical evaluations revealed that the mechanically alloyed and heat-treated Ti 2 wt %-Si powders have better corrosion resistance in 1.63 M H2SO4 than the pure Ti and MA Ti-Si samples. This is likely due to the particular microstructure produced during the milling and subsequent heat treatment.
- 19 October 2016
- Published by SAGE Publications in Powder Metallurgy
- Vol. 59 (5) , 359-369
ODS ferritic steels produced by an alternative route (STARS): microstructural characterisation after atomisation, HIPping and heat treatments
The conventional PM ODS Ferritic Steel (FS) processing route includes gas atomisation of steel powder and its mechanical alloying (MA) with Y2O3 powder particles to dissolve yttrium and form, during consolidation, a dispersion of oxide nanoparticles (Y–Ti–O) in a nanostructured matrix. This work presents an alternative route to produce ODS steels avoiding MA: STARS (Surface Treatment of gas Atomized powder followed by Reactive Synthesis). STARS FS powders with composition Fe–14Cr–2W–0.3Ti–0.23Y, already containing the nanoparticles precursors, were gas-atomized. Oxygen, Y and Ti contents were tailored to the required values to form Y–Ti–O nanoparticles during processing. Powders were HIPped at 900, 1220 and 1300°C. Specimens HIPped at 900 and 1220°C were heat treated (HT) at temperatures ranging from 1200 to 1320°C. The microstructural evolution with HIP and HT temperatures, including characterisation of nanoparticles and feasibility of achieving complete dissolution of prior particle boundaries (PPBs) were assessed.
- 19 October 2016
- Published by SAGE Publications in Powder Metallurgy
- Vol. 59 (5) , 359-369
ODS ferritic steels produced by an alternative route (STARS): microstructural characterisation after atomisation, HIPping and heat treatments
The conventional PM ODS Ferritic Steel (FS) processing route includes gas atomisation of steel powder and its mechanical alloying (MA) with Y2O3 powder particles to dissolve yttrium and form, during consolidation, a dispersion of oxide nanoparticles (Y–Ti–O) in a nanostructured matrix. This work presents an alternative route to produce ODS steels avoiding MA: STARS (Surface Treatment of gas Atomized powder followed by Reactive Synthesis). STARS FS powders with composition Fe–14Cr–2W–0.3Ti–0.23Y, already containing the nanoparticles precursors, were gas-atomized. Oxygen, Y and Ti contents were tailored to the required values to form Y–Ti–O nanoparticles during processing. Powders were HIPped at 900, 1220 and 1300°C. Specimens HIPped at 900 and 1220°C were heat treated (HT) at temperatures ranging from 1200 to 1320°C. The microstructural evolution with HIP and HT temperatures, including characterisation of nanoparticles and feasibility of achieving complete dissolution of prior particle boundaries (PPBs) were assessed.
- 28 February 2002
- Published by Elsevier in Scripta Materialia
- Vol. 46 (5) , 369-373
Sintering behaviour and fracture toughness characterization of D2 matrix tool steel, comparison with wrought and PM D2
- 28 February 2002
- Published by Elsevier in Scripta Materialia
- Vol. 46 (5) , 369-373
Sintering behaviour and fracture toughness characterization of D2 matrix tool steel, comparison with wrought and PM D2