Sang-Yung Shin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sang-Yung Shin has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Divya Sareen
Department of Chemistry, UGC-Centre of Advance Studies-I, Guru Nanak Dev University, Amritsar-143 005, India
1 shared publication - Dong-Min Yeo
Department of Electrical Engineering and Computer Science, Korea Advanced Institute of Science and Technology, 373-1 Guseong-dong, Yuseong-gu, Daejeon 305-701, Republic of Korea
1 shared publication - Jin Tae Kim
Quantum Technology Research Department Electronics and Telecommunications Research Institute (ETRI) Daejeon 34129 Republic of Korea
1 shared publication Jin-Soo Shin
$^{1}$ Department of Electrical Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon, Korea
1 shared publication- Jin-Soo Shin
Department of Electrical Engineering, Korea Advanced Institute of Science and Technology, 373-1, Guseong-dong, Yuseong-gu, Daejon 305-701, Republic of Korea
1 shared publication - Min-Cheol Oh
Department of Electronics Engineering, Pusan National University, Busan 46241, Republic of Korea
1 shared publication
Latest Publications
- 17 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 5 (5) , 6601909
Investigation and Improvement of 90$^{\circ}$ Direct Bends of Metal–Insulator–Silicon–Insulator–Metal Waveguides
We investigate 90° direct bends of metal-insulator-silicon-insulator-metal (MISIM) waveguides, which are hybrid plasmonic waveguides with replaceable insulators. First, we fabricate them using fully standard CMOS technology and characterize them. The experimental excess loss of the two consecutive 90° direct bends is 11, 7.4, and 4.5 dB when the width of the Si line of the MISIM waveguide is about 160, 190, and 220 nm, respectively. Second, we analyze the experimental results using the 3-D finite-difference time-domain method. Through the analysis, we investigate possible loss mechanisms of the 90° direct bend, which have not been studied to our knowledge. It has been found that the Si lines should be narrow to reduce the excess losses of the 90° direct bends. However, the wide Si lines are better for ease of fabrication and for small propagation losses. Finally, we demonstrate a modified low-loss 90° direct bend of the MISIM waveguide with a wide Si line.
- 17 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 5 (5) , 6601909
Investigation and Improvement of 90$^{\circ}$ Direct Bends of Metal–Insulator–Silicon–Insulator–Metal Waveguides
We investigate 90° direct bends of metal-insulator-silicon-insulator-metal (MISIM) waveguides, which are hybrid plasmonic waveguides with replaceable insulators. First, we fabricate them using fully standard CMOS technology and characterize them. The experimental excess loss of the two consecutive 90° direct bends is 11, 7.4, and 4.5 dB when the width of the Si line of the MISIM waveguide is about 160, 190, and 220 nm, respectively. Second, we analyze the experimental results using the 3-D finite-difference time-domain method. Through the analysis, we investigate possible loss mechanisms of the 90° direct bend, which have not been studied to our knowledge. It has been found that the Si lines should be narrow to reduce the excess losses of the 90° direct bends. However, the wide Si lines are better for ease of fabrication and for small propagation losses. Finally, we demonstrate a modified low-loss 90° direct bend of the MISIM waveguide with a wide Si line.
- 1 December 2009
- Published by Elsevier in Optics Communications
- Vol. 282 (23) , 4513-4517
Hybrid vertical directional coupling between a long range surface plasmon polariton waveguide and a dielectric waveguide
- 1 December 2009
- Published by Elsevier in Optics Communications
- Vol. 282 (23) , 4513-4517
Hybrid vertical directional coupling between a long range surface plasmon polariton waveguide and a dielectric waveguide
- 1 November 2006
- Published by Elsevier in Optics Communications
- Vol. 267 (2) , 388-393
Polymer-silica hybrid 1×2 thermooptic switch with low crosstalk
- 1 November 2006
- Published by Elsevier in Optics Communications
- Vol. 267 (2) , 388-393
Polymer-silica hybrid 1×2 thermooptic switch with low crosstalk
- 15 July 2001
- Published by Elsevier in Optics Communications
- Vol. 194 (4-6) , 309-312
Post-fabrication tuning of a polymeric grating-assisted codirectional coupler filter by photobleaching
- 15 July 2001
- Published by Elsevier in Optics Communications
- Vol. 194 (4-6) , 309-312
Post-fabrication tuning of a polymeric grating-assisted codirectional coupler filter by photobleaching
- 1 July 1996
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 8 (7) , 921-923
Integrated optical high-voltage sensor based on a polymeric Y-branch digital optical switch
An integrated optical high-voltage sensor is realized by fabricating a Y-branch digital optical switch in an electrooptic polymer. The measurement of ac high voltage is accomplished by using the linear transfer characteristics of the switch at zero bias voltage. Furthermore, the logarithmic ratio between the optical powers of two output ports may be used to remove the noise caused by the power fluctuations of a light source. The polymeric high-voltage sensor requires no electrical dc biases and no voltage dividers. It is also wavelength insensitive and fabrication-tolerant due to its use of mode evolution effects instead of interference. The measured sensing voltage range is as large as ac 500-V peak-to-peak.
- 1 July 1996
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 8 (7) , 921-923
Integrated optical high-voltage sensor based on a polymeric Y-branch digital optical switch
An integrated optical high-voltage sensor is realized by fabricating a Y-branch digital optical switch in an electrooptic polymer. The measurement of ac high voltage is accomplished by using the linear transfer characteristics of the switch at zero bias voltage. Furthermore, the logarithmic ratio between the optical powers of two output ports may be used to remove the noise caused by the power fluctuations of a light source. The polymeric high-voltage sensor requires no electrical dc biases and no voltage dividers. It is also wavelength insensitive and fabrication-tolerant due to its use of mode evolution effects instead of interference. The measured sensing voltage range is as large as ac 500-V peak-to-peak.