David K. Matlock
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
David K. Matlock has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- John G. Speer
Metallurgical and Materials Engineering, Colorado School of Mines, Golden, USA
6 shared publications - Radhakanta Rana
Tata Steel, Ijmuiden, The Netherlands
5 shared publications - Emmanuel De Moor
Advanced Steel Processing and Products Research Center, Colorado School of Mines, Golden, USA
4 shared publications John G. Speer
Advanced Steel Processing and Products Research Center Colorado School of Mines Golden CO 80401 USA
3 shared publications- Ana Luisa Rivas
Escuela Superior Politécnica del Litoral
2 shared publications - Afonso Reguly
Universidade Federal do Rio Grande do Sul
1 shared publication
Latest Publications
- Open Access
- 19 October 2022
- Published by Cambridge University Press (CUP) in Experimental Results
- Vol. 3, e23
Observing non-uniform, non-Lüders yielding in a cold-rolled medium manganese steel with digital image correlation
Digital image correlation (DIC) techniques were used to evaluate strain distributions along tensile gage lengths immediately after yielding of a medium manganese steel (7 wt% Mn) in samples cold rolled in the range of 1–6 pct. With an increase in cold work, DIC confirmed that the yielding behavior transitioned from nucleation and propagation of a single localized deformation zone (Lüders band) to uniform deformation, that is, no evidence of strain localization. At intermediate amounts of cold work, a unique yielding behavior was evident where the initially-low positive strain hardening rate increased with tensile strain until conventional strain hardening (i.e., decrease in strain hardening rate with strain). The intermediate yielding behavior was associated with the development of multiple non‑propagating regions of strain localization, an observation not previously evident without the use of DIC.
- 19 October 2022
- Published by Cambridge University Press (CUP) in Experimental Results
- Vol. 3, e23
Open AccessObserving non-uniform, non-Lüders yielding in a cold-rolled medium manganese steel with digital image correlation
Digital image correlation (DIC) techniques were used to evaluate strain distributions along tensile gage lengths immediately after yielding of a medium manganese steel (7 wt% Mn) in samples cold rolled in the range of 1–6 pct. With an increase in cold work, DIC confirmed that the yielding behavior transitioned from nucleation and propagation of a single localized deformation zone (Lüders band) to uniform deformation, that is, no evidence of strain localization. At intermediate amounts of cold work, a unique yielding behavior was evident where the initially-low positive strain hardening rate increased with tensile strain until conventional strain hardening (i.e., decrease in strain hardening rate with strain). The intermediate yielding behavior was associated with the development of multiple non‑propagating regions of strain localization, an observation not previously evident without the use of DIC.
- Open Access
Accelerated Ferrite-to-Austenite Transformation During Intercritical Annealing of Medium-Manganese Steels Due to Cold-Rolling
Prior cold deformation is known to influence the ferrite-to-austenite (α → γ) transformation in medium-manganese (Mn) steels that occurs during intercritical annealing. In the present study, a 7Mn steel with ultra-low residual carbon content and varying amounts of prior cold deformation was intercritically annealed using various heating rates in a dilatometer. The study was conducted using an ultra-low carbon steel so that assessments of austenite formation during intercritical annealing would reflect the effects of cold deformation on the α → γ transformation and Mn partitioning and not effect cementite formation and dissolution or paraequilibrium partitioning induced austenite growth from carbon. Increasing prior cold deformation was found to decrease the Ac1 temperature, increase austenite volume fraction during intercritical annealing, and increase the amount of austenite nucleation sites. Phase field simulations were also conducted in an attempt to simulate the apparent accelerated α → γ transformation with increasing prior cold deformation. Mechanisms for accelerated α → γ transformation explored with phase field simulations included an increase in the amount of austenite nucleation sites and an increased Mn diffusivity in ferrite. Simulations with different amounts of austenite nucleation sites and Mn diffusivity in ferrite predicted significant changes in the austenite volume fraction during intercritical annealing.
Open AccessAccelerated Ferrite-to-Austenite Transformation During Intercritical Annealing of Medium-Manganese Steels Due to Cold-Rolling
Prior cold deformation is known to influence the ferrite-to-austenite (α → γ) transformation in medium-manganese (Mn) steels that occurs during intercritical annealing. In the present study, a 7Mn steel with ultra-low residual carbon content and varying amounts of prior cold deformation was intercritically annealed using various heating rates in a dilatometer. The study was conducted using an ultra-low carbon steel so that assessments of austenite formation during intercritical annealing would reflect the effects of cold deformation on the α → γ transformation and Mn partitioning and not effect cementite formation and dissolution or paraequilibrium partitioning induced austenite growth from carbon. Increasing prior cold deformation was found to decrease the Ac1 temperature, increase austenite volume fraction during intercritical annealing, and increase the amount of austenite nucleation sites. Phase field simulations were also conducted in an attempt to simulate the apparent accelerated α → γ transformation with increasing prior cold deformation. Mechanisms for accelerated α → γ transformation explored with phase field simulations included an increase in the amount of austenite nucleation sites and an increased Mn diffusivity in ferrite. Simulations with different amounts of austenite nucleation sites and Mn diffusivity in ferrite predicted significant changes in the austenite volume fraction during intercritical annealing.
- 16 July 2019
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 50 (9) , 4016-4020
Effects of Hot Band Annealing on the Mechanical Properties of Cold-Rolled and Intercritically Annealed Medium Manganese Steels
- 16 July 2019
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 50 (9) , 4016-4020
Effects of Hot Band Annealing on the Mechanical Properties of Cold-Rolled and Intercritically Annealed Medium Manganese Steels
- Open Access
Processing Variants in Medium-Mn Steels
This paper highlights some recent efforts to extend the use of medium-Mn steels for applications other than intercritically batch-annealed steels with exceptional ductility (and strengths in the range of about 1000 MPa). These steels are shown to enable a range of promising properties. In hot-stamping application concepts, elevated Mn concentration helps to stabilize austenite and to provide a range of attractive property combinations, and also reduces the processing temperatures and likely eliminates the need for press quenching. The “double soaking” concept also provides a wide range of attractive mechanical property combinations that may be applicable in cold-forming applications, and could be implemented in continuous annealing and/or continuous galvanizing processes where Zn-coating would typically represent an additional austempering step. Quenching and partitioning of steels with elevated Mn concentrations have exhibited very high strengths, with attractive tensile ductility; and medium-Mn steels have been successfully designed for quenching and partitioning using room temperature as the quench temperature, thereby effectively decoupling the quenching and partitioning steps.
Open AccessProcessing Variants in Medium-Mn Steels
This paper highlights some recent efforts to extend the use of medium-Mn steels for applications other than intercritically batch-annealed steels with exceptional ductility (and strengths in the range of about 1000 MPa). These steels are shown to enable a range of promising properties. In hot-stamping application concepts, elevated Mn concentration helps to stabilize austenite and to provide a range of attractive property combinations, and also reduces the processing temperatures and likely eliminates the need for press quenching. The “double soaking” concept also provides a wide range of attractive mechanical property combinations that may be applicable in cold-forming applications, and could be implemented in continuous annealing and/or continuous galvanizing processes where Zn-coating would typically represent an additional austempering step. Quenching and partitioning of steels with elevated Mn concentrations have exhibited very high strengths, with attractive tensile ductility; and medium-Mn steels have been successfully designed for quenching and partitioning using room temperature as the quench temperature, thereby effectively decoupling the quenching and partitioning steps.
- 1 September 2018
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 735, 436-440
Deleterious effects of nitrogen annealing on the mechanical properties of medium manganese steels
- 1 September 2018
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 735, 436-440
Deleterious effects of nitrogen annealing on the mechanical properties of medium manganese steels
- 27 February 2018
- Published by Springer Nature in JOM
- Vol. 70 (5) , 706-713
On the Importance of Adiabatic Heating on Deformation Behavior of Medium-Manganese Sheet Steels
- 27 February 2018
- Published by Springer Nature in JOM
- Vol. 70 (5) , 706-713
On the Importance of Adiabatic Heating on Deformation Behavior of Medium-Manganese Sheet Steels
- 13 April 2015
- Published by Wiley in Steel Research International
- Vol. 86 (10) , 1139-1150
A Composite Modeling Analysis of the Deformation Behavior of Medium Manganese Steels
A composite model with different assumed flow behaviors for the individual microstructural constituents and stability parameters for the metastable austenite transformation is presented and shown to provide design insight into the development of third‐generation advanced high strength steels with a wide spectrum of tensile properties. The deformation behavior of a Fe‐7.09 Mn‐0.099 C‐0.13 Si (wt%) steel is evaluated with uniaxial tensile testing and the results are correlated with predictions of the composite model. It is shown that the present simple composite model can predict tensile strength and uniform elongation with good accuracy over a range of austenite volume fractions in the steel. The analysis is based on Mn enrichment into austenite during intercritical annealing of the steel resulting in microstructures with significant variations in the amount and stability of austenite. Strategies for controlling the stability and amount of austenite in medium Mn steels are also presented in low carbon, nominally 5–10 wt% Mn‐containing steels with/without Al as an alloying addition.
- 13 April 2015
- Published by Wiley in Steel Research International
- Vol. 86 (10) , 1139-1150
A Composite Modeling Analysis of the Deformation Behavior of Medium Manganese Steels
A composite model with different assumed flow behaviors for the individual microstructural constituents and stability parameters for the metastable austenite transformation is presented and shown to provide design insight into the development of third‐generation advanced high strength steels with a wide spectrum of tensile properties. The deformation behavior of a Fe‐7.09 Mn‐0.099 C‐0.13 Si (wt%) steel is evaluated with uniaxial tensile testing and the results are correlated with predictions of the composite model. It is shown that the present simple composite model can predict tensile strength and uniform elongation with good accuracy over a range of austenite volume fractions in the steel. The analysis is based on Mn enrichment into austenite during intercritical annealing of the steel resulting in microstructures with significant variations in the amount and stability of austenite. Strategies for controlling the stability and amount of austenite in medium Mn steels are also presented in low carbon, nominally 5–10 wt% Mn‐containing steels with/without Al as an alloying addition.
- 22 March 2010
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 25 (1-3) , 7-13
Processing Opportunities for New Advanced High-Strength Sheet Steels
Currently there is considerable interest in developments leading to new advanced high-strength sheet steels (AHSS) for automotive and other transportation applications that demand high strength, light weight materials. Design requirements will involve material properties with strengths greater than currently available dual phase and transformation-induced plasticity (TRIP) steels (steels in this group are referred to as the “First Generation” of AHSS), with good ductility and formability, but produced at a cost less than the high ductility stainless steels or high manganese TWIP steels (materials referred to as the “Second Generation” of AHSS). Recent studies have shown that materials that satisfy the required property/cost combinations will include complex microstructures containing high amounts of retained austenite in combination with a high strength constituent that may be ultrafine grained ferrite, martensite, bainite, and/or combinations of ferrite-based constituents. In this article, selected methodologies leading to the production of new AHSS materials will be reviewed and assessed to provide a framework for consideration of new concepts and processing routes that will be required in production operations.
- 22 March 2010
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 25 (1-3) , 7-13
Processing Opportunities for New Advanced High-Strength Sheet Steels
Currently there is considerable interest in developments leading to new advanced high-strength sheet steels (AHSS) for automotive and other transportation applications that demand high strength, light weight materials. Design requirements will involve material properties with strengths greater than currently available dual phase and transformation-induced plasticity (TRIP) steels (steels in this group are referred to as the “First Generation” of AHSS), with good ductility and formability, but produced at a cost less than the high ductility stainless steels or high manganese TWIP steels (materials referred to as the “Second Generation” of AHSS). Recent studies have shown that materials that satisfy the required property/cost combinations will include complex microstructures containing high amounts of retained austenite in combination with a high strength constituent that may be ultrafine grained ferrite, martensite, bainite, and/or combinations of ferrite-based constituents. In this article, selected methodologies leading to the production of new AHSS materials will be reviewed and assessed to provide a framework for consideration of new concepts and processing routes that will be required in production operations.
- Open Access
- 30 October 2008
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 44 (5) , 447-456
Extracción electroquímica de carburos de microaleación en Nb-acero
La técnica de extracción electroquímica fue empleada para evaluar su efectividad en la caracterización de precipitados en aceros microaleados. Para realizar el estudio, se utilizó un acero SAE 8620 modificado con niobio. La investigación se llevó a cabo variando la composición del electrolito utilizado en la disolución electroquímica de la matriz y el tamaño de poro de los filtros usados para recolectar las partículas precipitadas. La cuantificación del contenido de Nb se hizo por espectroscopia de emisión atómica de plasma (ICP-AES). Además, las muestras obtenidas por réplicas de extracción y las provenientes de los residuos recolectados en los filtros fueron analizadas mediante microscopía electrónica de transmisión. Estas últimas muestras, también fueron caracterizadas por difracción de rayos X. Los resultados mostraron que la velocidad de disolución electroquímica de las muestras es mayor en el electrolito acuoso con 10 vol. % HCl. Adicionalmente, el análisis mediante microscopía electrónica de transmisión, en combinación con los análisis químicos mediante ICP-AES, mostró que las partículas de (Nb,Ti)C son recolectadas en filtros de acetato con tamaños de poro mucho mayor que el tamaño de las partículas precipitadas.
- 30 October 2008
- Published by Editorial CSIC in Revista de Metalurgia
- Vol. 44 (5) , 447-456
Open AccessExtracción electroquímica de carburos de microaleación en Nb-acero
La técnica de extracción electroquímica fue empleada para evaluar su efectividad en la caracterización de precipitados en aceros microaleados. Para realizar el estudio, se utilizó un acero SAE 8620 modificado con niobio. La investigación se llevó a cabo variando la composición del electrolito utilizado en la disolución electroquímica de la matriz y el tamaño de poro de los filtros usados para recolectar las partículas precipitadas. La cuantificación del contenido de Nb se hizo por espectroscopia de emisión atómica de plasma (ICP-AES). Además, las muestras obtenidas por réplicas de extracción y las provenientes de los residuos recolectados en los filtros fueron analizadas mediante microscopía electrónica de transmisión. Estas últimas muestras, también fueron caracterizadas por difracción de rayos X. Los resultados mostraron que la velocidad de disolución electroquímica de las muestras es mayor en el electrolito acuoso con 10 vol. % HCl. Adicionalmente, el análisis mediante microscopía electrónica de transmisión, en combinación con los análisis químicos mediante ICP-AES, mostró que las partículas de (Nb,Ti)C son recolectadas en filtros de acetato con tamaños de poro mucho mayor que el tamaño de las partículas precipitadas.
- 31 May 2008
- Published by Elsevier in Materials Characterization
- Vol. 59 (5) , 571-577
Quantitative analysis of Nb in solution in a microalloyed carburizing steel by electrochemical etching
- 31 May 2008
- Published by Elsevier in Materials Characterization
- Vol. 59 (5) , 571-577
Quantitative analysis of Nb in solution in a microalloyed carburizing steel by electrochemical etching