Dionyz Pogany
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dionyz Pogany has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
S. Bychikhin
Institute for Solid-State Electronics, Vienna University of Technology, Vienna, Austria
6 shared publications- Gottfried Strasser
Institute of Solid State Electronics E362, Technische Universität Wien
4 shared publications A. Alexewicz
3 shared publications- Erich Gornik
Institute for Solid State Electronics, Vienna University of Technology, Gußhausstraße 25-25a (Gebäude CH), 1040 Wien, Austria
3 shared publications - Hans-Martin Ritter
Nexperia Germany GmbH, Hamburg, Germany
3 shared publications M. Stecher
Infineon Technologies, Neubiberg, Germany
3 shared publications
Latest Publications
- Open Access
- 11 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7281-7286
I – V Hysteresis in ESD Protection SCR Due to Jumping Between Bulk and Surface Current Paths
The origin of an I – V hysteresis and sharp snapback of single finger silicon-controlled rectifiers (SCRs) for system-level electrostatic discharge (ESD) protection is investigated experimentally and by 2-D technology computer-aided design (TCAD) simulation. Emission microscopy (EMMI) measurements indicate spatial changes in current flow, which is reproduced in simulations using up and down current sweeps. A bulk current path, via two serially connected n-p-n transistors, comprising buried layers (BLs) gives rise to a high-voltage I – V (HV-IV) branch. The sharp snapback is caused by a sudden jump of the current path from the bulk to surface region, thus activating the SCR. The TCAD reveals that charge conditions at the surface determine the stability of the bulk path, and thus the existence of the hysteresis, via the location of impact ionization generation source. The results are important for understanding the complex interplay and coupling of parallel current paths in SCRs.
- 11 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7281-7286
Open AccessI – V Hysteresis in ESD Protection SCR Due to Jumping Between Bulk and Surface Current Paths
The origin of an I – V hysteresis and sharp snapback of single finger silicon-controlled rectifiers (SCRs) for system-level electrostatic discharge (ESD) protection is investigated experimentally and by 2-D technology computer-aided design (TCAD) simulation. Emission microscopy (EMMI) measurements indicate spatial changes in current flow, which is reproduced in simulations using up and down current sweeps. A bulk current path, via two serially connected n-p-n transistors, comprising buried layers (BLs) gives rise to a high-voltage I – V (HV-IV) branch. The sharp snapback is caused by a sudden jump of the current path from the bulk to surface region, thus activating the SCR. The TCAD reveals that charge conditions at the surface determine the stability of the bulk path, and thus the existence of the hysteresis, via the location of impact ionization generation source. The results are important for understanding the complex interplay and coupling of parallel current paths in SCRs.
- 5 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4214-4222
3-D TCAD Methodology for Simulating Double-Hysteresis Filamentary I–V Behavior and Holding Current in ESD Protection SCRs
Current filament (CF)-related double-hysteresis ${I}$ – ${V}$ behavior and holding current, ${I} _{\text {HOLD}}$ , are analyzed using experiments and 3-D technology computer-aided design (TCAD) simulation in silicon-controlled rectifiers (SCR) for system-level electrostatic discharge (ESD) protection. Our 3-D TCAD methodology uses up and down quasi-dc current sweeps to reveal a memory effect in the current density distribution along the device width. ${I} _{\text {HOLD}}$ is related to the smallest possible CF where the self-sustaining SCR action takes place during down current sweep. ${I} _{\text {HOLD}}$ exhibits a nontrivial dependence on device width, depending on whether a CF is created or not. Analyzing devices of different layouts shows that ${I} _{\text {HOLD}}$ values determined from experiments and 3-D TCAD are almost layout-independent and substantially lower than those evaluated from 2-D TCAD. ${I} _{\text {HOLD}}$ calculated by 3-D TCAD in edge-terminated devices is higher than that in 3-D structures obtained from simple width-extended 2-D doping profiles. The use of latter devices, thus, simplifies the 3-D TCAD ${I}$ – ${V}$ analysis and provides a safe margin for ${I} _{\text {HOLD}}$ prediction. The work is relevant for designing the latch-up immunity of ESD protection devices, and it also shows that conventional 2-D TCAD can provide unwanted overestimation of ${I} _{\text {HOLD}}$ .
- 5 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (9) , 4214-4222
3-D TCAD Methodology for Simulating Double-Hysteresis Filamentary I–V Behavior and Holding Current in ESD Protection SCRs
Current filament (CF)-related double-hysteresis ${I}$ – ${V}$ behavior and holding current, ${I} _{\text {HOLD}}$ , are analyzed using experiments and 3-D technology computer-aided design (TCAD) simulation in silicon-controlled rectifiers (SCR) for system-level electrostatic discharge (ESD) protection. Our 3-D TCAD methodology uses up and down quasi-dc current sweeps to reveal a memory effect in the current density distribution along the device width. ${I} _{\text {HOLD}}$ is related to the smallest possible CF where the self-sustaining SCR action takes place during down current sweep. ${I} _{\text {HOLD}}$ exhibits a nontrivial dependence on device width, depending on whether a CF is created or not. Analyzing devices of different layouts shows that ${I} _{\text {HOLD}}$ values determined from experiments and 3-D TCAD are almost layout-independent and substantially lower than those evaluated from 2-D TCAD. ${I} _{\text {HOLD}}$ calculated by 3-D TCAD in edge-terminated devices is higher than that in 3-D structures obtained from simple width-extended 2-D doping profiles. The use of latter devices, thus, simplifies the 3-D TCAD ${I}$ – ${V}$ analysis and provides a safe margin for ${I} _{\text {HOLD}}$ prediction. The work is relevant for designing the latch-up immunity of ESD protection devices, and it also shows that conventional 2-D TCAD can provide unwanted overestimation of ${I} _{\text {HOLD}}$ .
- 26 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 20 (4) , 632-640
Simultaneous and Sequential Triggering in Multi-Finger Floating-Base SCRs Depending on TLP Pulse Rise Time
Multi-finger floating-base silicon controlled rectifiers (SCRs) of discrete technologies are investigated by transmission line pulses (TLP) with short (300ps) and long (10ns) pulse rise times (RT). Transient interferometric mapping (TIM) is applied to study the finger triggering dynamics. The measurements are correlated with TCAD simulation. It is found that for short RT the fingers trigger simultaneously which is due to the positive influence of a voltage overshoot related to delayed conductivity modulation. For long RT the fingers trigger sequentially which is accompanied by the voltage drops near the holding voltage. The time delay between the triggering of neighboring fingers is in the 3-150ns range and depends on the actual current density in fingers. The sequential finger triggering is due to lateral carrier diffusion-limited processes and the coupling via substrate currents.
- 26 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 20 (4) , 632-640
Simultaneous and Sequential Triggering in Multi-Finger Floating-Base SCRs Depending on TLP Pulse Rise Time
Multi-finger floating-base silicon controlled rectifiers (SCRs) of discrete technologies are investigated by transmission line pulses (TLP) with short (300ps) and long (10ns) pulse rise times (RT). Transient interferometric mapping (TIM) is applied to study the finger triggering dynamics. The measurements are correlated with TCAD simulation. It is found that for short RT the fingers trigger simultaneously which is due to the positive influence of a voltage overshoot related to delayed conductivity modulation. For long RT the fingers trigger sequentially which is accompanied by the voltage drops near the holding voltage. The time delay between the triggering of neighboring fingers is in the 3-150ns range and depends on the actual current density in fingers. The sequential finger triggering is due to lateral carrier diffusion-limited processes and the coupling via substrate currents.
- 1 November 2013
- Published by Elsevier in Solid-State Electronics
- Vol. 89, 207-211
Current collapse reduction in InAlGaN/GaN high electron mobility transistors by surface treatment of thermally stable ultrathin in situ SiN passivation
- 1 November 2013
- Published by Elsevier in Solid-State Electronics
- Vol. 89, 207-211
Current collapse reduction in InAlGaN/GaN high electron mobility transistors by surface treatment of thermally stable ultrathin in situ SiN passivation
- 1 July 2012
- Published by Elsevier in Thin Solid Films
- Vol. 520 (19) , 6230-6232
Explanation of threshold voltage scaling in enhancement-mode InAlN/AlN–GaN metal oxide semiconductor high electron mobility transistors on Si substrates
- 1 July 2012
- Published by Elsevier in Thin Solid Films
- Vol. 520 (19) , 6230-6232
Explanation of threshold voltage scaling in enhancement-mode InAlN/AlN–GaN metal oxide semiconductor high electron mobility transistors on Si substrates
- 2 April 2012
- Published by AIP Publishing in Applied Physics Letters
- Vol. 100 (14) , 143507
Random telegraph signal noise in gate current of unstressed and reverse-bias-stressed AlGaN/GaN high electron mobility transistors
Random telegraph signal (RTS) fluctuations with relative amplitude up to 50% are observed in forward and reverse gate current of unstressed and reverse-bias-stressed AlGaN/GaN high electron mobility transistors. Measurements of RTS amplitude and mean pulse widths as a function of forward gate bias indicate that the RTS is due to modulation of current along an intrinsic or stress-induced percolation path across the AlGaN-barrier by electron capture and emission on a trap within the barrier. Processes of electron capture from GaN to trap and subsequent tunneling to metal gate or electron exchange between GaN channel and the trap are considered.
- 2 April 2012
- Published by AIP Publishing in Applied Physics Letters
- Vol. 100 (14) , 143507
Random telegraph signal noise in gate current of unstressed and reverse-bias-stressed AlGaN/GaN high electron mobility transistors
Random telegraph signal (RTS) fluctuations with relative amplitude up to 50% are observed in forward and reverse gate current of unstressed and reverse-bias-stressed AlGaN/GaN high electron mobility transistors. Measurements of RTS amplitude and mean pulse widths as a function of forward gate bias indicate that the RTS is due to modulation of current along an intrinsic or stress-induced percolation path across the AlGaN-barrier by electron capture and emission on a trap within the barrier. Processes of electron capture from GaN to trap and subsequent tunneling to metal gate or electron exchange between GaN channel and the trap are considered.
- 13 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 58 (2) , 411-418
Measuring Holding Voltage Related to Homogeneous Current Flow in Wide ESD Protection Structures Using Multilevel TLP
Due to the negative-differential-resistance-related instability, the current-density distribution in sufficiently wide devices exhibiting S-shaped I-V characteristics becomes inherently inhomogeneous along the device width. High-current-density on-state (i.e., a current filament) and low-current-density off-state regions are spontaneously formed, leading to the formation of a vertical branch in the I-V curve at a so-called coexistence voltage uCO. In electrostatic discharge (ESD) protection devices (PDs), this vertical I- branch usually determines the lowest voltage point that can be accessed by a conventional transmission line pulser (TLP). However, the real holding point of device VH, which is related to an I-V part with a homogeneous current distribution, lies below uCO, i.e., VH <; uCO. Here, we present a method on how to determine VH and the I-V branch below uCO, which is “hidden” when using a conventional TLP analysis. We use a multilevel TLP system and demonstrate it on a 90-nm technology silicon-controlled rectifier ESD PD. Measurement considerations, which take into account the finite speed of the on-state spreading effect and the self-heating effect, are discussed. Implications relevant for latch-up prevention and for the comparison of experiments with 2-D and 3-D technology computer-aided design simulations are also given.
- 13 December 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 58 (2) , 411-418
Measuring Holding Voltage Related to Homogeneous Current Flow in Wide ESD Protection Structures Using Multilevel TLP
Due to the negative-differential-resistance-related instability, the current-density distribution in sufficiently wide devices exhibiting S-shaped I-V characteristics becomes inherently inhomogeneous along the device width. High-current-density on-state (i.e., a current filament) and low-current-density off-state regions are spontaneously formed, leading to the formation of a vertical branch in the I-V curve at a so-called coexistence voltage uCO. In electrostatic discharge (ESD) protection devices (PDs), this vertical I- branch usually determines the lowest voltage point that can be accessed by a conventional transmission line pulser (TLP). However, the real holding point of device VH, which is related to an I-V part with a homogeneous current distribution, lies below uCO, i.e., VH <; uCO. Here, we present a method on how to determine VH and the I-V branch below uCO, which is “hidden” when using a conventional TLP analysis. We use a multilevel TLP system and demonstrate it on a 90-nm technology silicon-controlled rectifier ESD PD. Measurement considerations, which take into account the finite speed of the on-state spreading effect and the self-heating effect, are discussed. Implications relevant for latch-up prevention and for the comparison of experiments with 2-D and 3-D technology computer-aided design simulations are also given.
- 1 September 2007
- Published by Elsevier in Microelectronics Reliability
- Vol. 47 (9) , 1649-1652
Thermal analysis of InGaN/GaN (GaN substrate) laser diodes using transient interferometric mapping
- 1 September 2007
- Published by Elsevier in Microelectronics Reliability
- Vol. 47 (9) , 1649-1652
Thermal analysis of InGaN/GaN (GaN substrate) laser diodes using transient interferometric mapping
- 15 June 2005
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 97 (12)
Low-frequency noise sources in as-prepared and aged GaN-based light-emitting diodes
The low-frequency noise sources are investigated in as-prepared and aged GaN light-emitting diodes (LEDs). Accelerated aging is performed by thermal ( at ) and electrical forward-bias stressing (20 and for ). At low currents , where is a critical current, the low-frequency noise is dominated by random telegraph signal (RTS) noise on top of the noise. An explanation is given for the giant relative current jumps and an expression for is derived. The RTS noise in our devices is a less-sensitive diagnostic tool for studying the results of accelerated aging. Two components of the noise were observed: one is related to the quantum-well junction and the other is due to series resistance noise. The two spectra have different current dependences. It was found that the junction noise is not significantly affected by aging. However, a strong increase in series resistance noise, by a factor of 60–800 compared to unstressed devices, is observed after strong electrical and thermal aging. This high increase goes hand in hand with a relatively small increase in the value of the series resistance (13%–90%). This makes noise a very sensitive reliability indicator for GaN LEDs after accelerated aging. We discuss the physical origin of LED degradation.- 15 June 2005
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 97 (12)
Low-frequency noise sources in as-prepared and aged GaN-based light-emitting diodes
The low-frequency noise sources are investigated in as-prepared and aged GaN light-emitting diodes (LEDs). Accelerated aging is performed by thermal ( at ) and electrical forward-bias stressing (20 and for ). At low currents , where is a critical current, the low-frequency noise is dominated by random telegraph signal (RTS) noise on top of the noise. An explanation is given for the giant relative current jumps and an expression for is derived. The RTS noise in our devices is a less-sensitive diagnostic tool for studying the results of accelerated aging. Two components of the noise were observed: one is related to the quantum-well junction and the other is due to series resistance noise. The two spectra have different current dependences. It was found that the junction noise is not significantly affected by aging. However, a strong increase in series resistance noise, by a factor of 60–800 compared to unstressed devices, is observed after strong electrical and thermal aging. This high increase goes hand in hand with a relatively small increase in the value of the series resistance (13%–90%). This makes noise a very sensitive reliability indicator for GaN LEDs after accelerated aging. We discuss the physical origin of LED degradation.