Colin A. Taylor
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Colin A. Taylor has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Matt Dietz
University of Bristol
7 shared publications - Adam J. Crewe
University of Bristol
6 shared publications - Luiza Dihoru
Department of Civil Engineering University of Bristol Bristol UK
5 shared publications - Panos Kloukinas
School of Engineering, University of Greenwich, ME4 4TB, Chatham Maritime, Kent, UK, UK
3 shared publications - John H. G. Macdonald
Department of Civil Engineering, University of Bristol, Bristol, UK
2 shared publications - Kate Bourne
Univ Bristol, Fac Engn, Earthquake & Geotech Engn Grp, Bristol BS8 1TR, Avon, England
2 shared publications
Latest Publications
- Open Access
Design and Calibration of a Hall Effect System for Measurement of Six-Degree-of-Freedom Motion within a Stacked Column
This paper presents the design, development and evaluation of a unique non-contact instrumentation system that can accurately measure the interface displacement between two rigid components in six degrees of freedom. The system was developed to allow measurement of the relative displacements between interfaces within a stacked column of brick-like components, with an accuracy of 0.05 mm and 0.1 degrees. The columns comprised up to 14 components, with each component being a scale model of a graphite brick within an Advanced Gas-cooled Reactor core. A set of 585 of these columns makes up the Multi Layer Array, which was designed to investigate the response of the reactor core to seismic inputs, with excitation levels up to 1 g from 0 to 100 Hz. The nature of the application required a compact and robust design capable of accurately recording fully coupled motion in all six degrees of freedom during dynamic testing. The novel design implemented 12 Hall effect sensors with a calibration procedure based on system identification techniques. The measurement uncertainty was ±0.050 mm for displacement and ±0.052 degrees for rotation, and the system can tolerate loss of data from two sensors with the uncertainly increasing to only 0.061 mm in translation and 0.088 degrees in rotation. The system has been deployed in a research programme that has enabled EDF to present seismic safety cases to the Office for Nuclear Regulation, resulting in life extension approvals for several reactors. The measurement system developed could be readily applied to other situations where the imposed level of stress at the interface causes negligible material strain, and accurate non-contact six-degree-of-freedom interface measurement is required.
Open AccessDesign and Calibration of a Hall Effect System for Measurement of Six-Degree-of-Freedom Motion within a Stacked Column
This paper presents the design, development and evaluation of a unique non-contact instrumentation system that can accurately measure the interface displacement between two rigid components in six degrees of freedom. The system was developed to allow measurement of the relative displacements between interfaces within a stacked column of brick-like components, with an accuracy of 0.05 mm and 0.1 degrees. The columns comprised up to 14 components, with each component being a scale model of a graphite brick within an Advanced Gas-cooled Reactor core. A set of 585 of these columns makes up the Multi Layer Array, which was designed to investigate the response of the reactor core to seismic inputs, with excitation levels up to 1 g from 0 to 100 Hz. The nature of the application required a compact and robust design capable of accurately recording fully coupled motion in all six degrees of freedom during dynamic testing. The novel design implemented 12 Hall effect sensors with a calibration procedure based on system identification techniques. The measurement uncertainty was ±0.050 mm for displacement and ±0.052 degrees for rotation, and the system can tolerate loss of data from two sensors with the uncertainly increasing to only 0.061 mm in translation and 0.088 degrees in rotation. The system has been deployed in a research programme that has enabled EDF to present seismic safety cases to the Office for Nuclear Regulation, resulting in life extension approvals for several reactors. The measurement system developed could be readily applied to other situations where the imposed level of stress at the interface causes negligible material strain, and accurate non-contact six-degree-of-freedom interface measurement is required.
- Open Access
- 1 November 2017
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 323, 269-279
The development of a physical model of an Advanced Gas Cooled Reactor core: Outline of the feasibility study
- 1 November 2017
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 323, 269-279
Open AccessThe development of a physical model of an Advanced Gas Cooled Reactor core: Outline of the feasibility study
- 19 April 2015
- Published by Springer Nature
- p. 269-293
Seismic Behaviour of Thin-Bed Layered Unreinforced Clay Masonry Frames with T- or L-Shaped Piers
- 19 April 2015
- Published by Springer Nature
- p. 269-293
Seismic Behaviour of Thin-Bed Layered Unreinforced Clay Masonry Frames with T- or L-Shaped Piers
- 1 January 2014
- Published by Seismological Society of America (SSA) in Seismological Research Letters
- Vol. 85 (1) , 189-191
Reply to "Comment on 'Seismic Hazard Analysis for the U.K.: Sensitivity to Spatial Seismicity Modelling and Ground Motion Prediction Equations' by Katsuichiro Goda, Willy P. Aspinall, and Colin A. Taylor," by Roger M. W. Musson
- 1 January 2014
- Published by Seismological Society of America (SSA) in Seismological Research Letters
- Vol. 85 (1) , 189-191
Reply to "Comment on 'Seismic Hazard Analysis for the U.K.: Sensitivity to Spatial Seismicity Modelling and Ground Motion Prediction Equations' by Katsuichiro Goda, Willy P. Aspinall, and Colin A. Taylor," by Roger M. W. Musson
- 20 September 2011
- Published by Springer Nature
- p. 135-158
Model Container Design for Soil-Structure Interaction Studies
- 20 September 2011
- Published by Springer Nature
- p. 135-158
Model Container Design for Soil-Structure Interaction Studies
- 20 September 2011
- Published by Springer Nature
- p. 119-134
Performance Requirements of Actuation Systems for Dynamic Testing in the European Earthquake Engineering Laboratories
- 20 September 2011
- Published by Springer Nature
- p. 119-134
Performance Requirements of Actuation Systems for Dynamic Testing in the European Earthquake Engineering Laboratories
- 20 September 2011
- Published by Springer Nature
- p. 21-41
Earthquake and Large Structures Testing at the Bristol Laboratory for Advanced Dynamics Engineering
- 20 September 2011
- Published by Springer Nature
- p. 21-41
Earthquake and Large Structures Testing at the Bristol Laboratory for Advanced Dynamics Engineering
- 1 August 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 133 (8) , 864-873
Adaptive Control Strategy for Dynamic Substructuring Tests
Real-time dynamic substructuring, or hybrid testing, is a technique that enables experimental testing of critical elements of a complete structure. The structure in question is decomposed into at least two parts: the critical element, which is physically tested, and the remainder of the structure, which is modeled numerically. For accurate replication of the system to be emulated, the two parts must interact, via a controller to compensate for the actuator dynamics, in real-time, and with minimal errors at their interfaces. During development, the adaptive minimal controller synthesis (MCS) algorithm controller has previously been implemented for substructuring of a one-degree-of-freedom mass-spring-damper system. The potential advantage that MCS has over a traditional linear controller is its lack of reliance on detailed knowledge of the experimental specimen dynamics. This paper presents the MCSmd control strategy, an improved MCS-based strategy for substructure testing, using a modified demand (md) sig...
- 1 August 2007
- Published by American Society of Civil Engineers (ASCE) in Journal of Engineering Mechanics
- Vol. 133 (8) , 864-873
Adaptive Control Strategy for Dynamic Substructuring Tests
Real-time dynamic substructuring, or hybrid testing, is a technique that enables experimental testing of critical elements of a complete structure. The structure in question is decomposed into at least two parts: the critical element, which is physically tested, and the remainder of the structure, which is modeled numerically. For accurate replication of the system to be emulated, the two parts must interact, via a controller to compensate for the actuator dynamics, in real-time, and with minimal errors at their interfaces. During development, the adaptive minimal controller synthesis (MCS) algorithm controller has previously been implemented for substructuring of a one-degree-of-freedom mass-spring-damper system. The potential advantage that MCS has over a traditional linear controller is its lack of reliance on detailed knowledge of the experimental specimen dynamics. This paper presents the MCSmd control strategy, an improved MCS-based strategy for substructure testing, using a modified demand (md) sig...
- 1 January 2001
- Published by Elsevier
- p. 497-502
Dynamic Soil-Structure Interaction of Earth Reinforced Walls
- 1 January 2001
- Published by Elsevier
- p. 497-502
Dynamic Soil-Structure Interaction of Earth Reinforced Walls