Ahmad A. Al-Qaisia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ahmad A. Al-Qaisia has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
M.N. Hamdan
Mechanical Engineering Department, University of Jordan Amman, Jordan
4 shared publicationsB.O. Al-Bedoor
2 shared publications- Hasan Katkhuda
Department of Civil Engineering, Faculty of Engineering, The Hashemite University, Zarqa, Jordan
2 shared publications - Nasim Shatarat
Department of Civil Engineering, School of Engineering, University of Jordan, Amman, Jordan
2 shared publications - Hamza Mobideen
Department of Civil Engineering, School of Engineering, University of Jordan, Amman, Jordan
1 shared publication - Hebah Al-Zu’bi
Department of Civil Engineering, The University of Jordan, Amman 11942, Jordan
1 shared publication
Latest Publications
- 13 November 2023
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 8 (12) , 1-20
Influence of basalt stirrups and bars on the performance of shear in beams
- 13 November 2023
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 8 (12) , 1-20
Influence of basalt stirrups and bars on the performance of shear in beams
- Open Access
Influence of Temperature on Shear Behavior of Lightweight Reinforced Concrete Beams Using Pozzolana Aggregate and Expanded Polystyrene Beads
The innovation inherent to employing expanded polystyrene (EPS) beads lies in its transformative impact on traditional concrete practices. Through the incorporation of EPS beads in concrete mixtures, a novel approach emerges that significantly alters the material’s characteristics, and opens up new avenues for construction and design. Studying the shear behavior of RC beams made with EPS beads is essential for advancing knowledge, improving design practices, ensuring structural integrity, and promoting the effective and responsible use of innovative materials in construction. This research experimentally investigated the effect of using EPS beads and pozzolana aggregate (PA) on the shear behavior of the RC beams. A total of 27 simply supported rectangular beams were cast, using three novel distinct mix designs, and were subjected to two-point load testing until failure. These three mixes were categorized as follows: a control mix, a mix with only EPS, and a mix with EPS, along with an additive. The ultimate failure load was experimentally recorded for all specimens, and the influence of the temperature (300 °C and 600 °C) on the RC beams made with EPS was examined. The findings revealed a reduction in the concrete compressive strength and density in the beams containing EPS and EPS with superplasticizers of (21.7%, 24.9%) and (11.3%, 16.2%), respectively. Additionally, EPS played a significant role in diminishing the ultimate shear capacity of the beams, compared to the control beams, by about 19.4%. However, the addition of a superplasticizer along with the EPS helped to maintain the beam capacity, to some extent. Conversely, the beams exposed to a temperature of 300 °C exhibited an almost similar capacity to that of the control beams without heating. Nevertheless, at 600 °C, the beams displayed a noticeable decrease in the ultimate load capacity, compared to the unheated control beams.
Open AccessInfluence of Temperature on Shear Behavior of Lightweight Reinforced Concrete Beams Using Pozzolana Aggregate and Expanded Polystyrene Beads
The innovation inherent to employing expanded polystyrene (EPS) beads lies in its transformative impact on traditional concrete practices. Through the incorporation of EPS beads in concrete mixtures, a novel approach emerges that significantly alters the material’s characteristics, and opens up new avenues for construction and design. Studying the shear behavior of RC beams made with EPS beads is essential for advancing knowledge, improving design practices, ensuring structural integrity, and promoting the effective and responsible use of innovative materials in construction. This research experimentally investigated the effect of using EPS beads and pozzolana aggregate (PA) on the shear behavior of the RC beams. A total of 27 simply supported rectangular beams were cast, using three novel distinct mix designs, and were subjected to two-point load testing until failure. These three mixes were categorized as follows: a control mix, a mix with only EPS, and a mix with EPS, along with an additive. The ultimate failure load was experimentally recorded for all specimens, and the influence of the temperature (300 °C and 600 °C) on the RC beams made with EPS was examined. The findings revealed a reduction in the concrete compressive strength and density in the beams containing EPS and EPS with superplasticizers of (21.7%, 24.9%) and (11.3%, 16.2%), respectively. Additionally, EPS played a significant role in diminishing the ultimate shear capacity of the beams, compared to the control beams, by about 19.4%. However, the addition of a superplasticizer along with the EPS helped to maintain the beam capacity, to some extent. Conversely, the beams exposed to a temperature of 300 °C exhibited an almost similar capacity to that of the control beams without heating. Nevertheless, at 600 °C, the beams displayed a noticeable decrease in the ultimate load capacity, compared to the unheated control beams.
- 1 July 2010
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 329 (15) , 3121-3136
Modeling and study of dynamic performance of a valveless micropump
- 1 July 2010
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 329 (15) , 3121-3136
Modeling and study of dynamic performance of a valveless micropump
- 12 March 2010
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 16 (6) , 853-877
Primary Resonance Response of a Beam with a Differential Edge Settlement Attached to an Elastic Foundation
In this work, we study, through one-mode simplification, the influence of frequency curve veering on the primary resonance response of an elastic Euler-Bernoulli attached to a linear Winkler elastic foundation. The beam is a hinged-hinged with one torsional spring at one end, has an initial 1/4 sine deflection shape due to a constant differential edge settlement and is subjected to a uniformly distributed vertical load which is harmonically varying with a time part and a large mean part. A combined numerical-analytical procedure which accounts for the nonlinear interdependence between the vertical deflection and induced axial force due to mid-plane stretching was used to determine the beam static deflection. The assumed single mode approach is used to obtain the reduced nonlinear temporal equation of motion about the static equilibrium deflection which contains quadratic and cubic nonlinear terms. The results of numerical simulation indicate that the coefficients of the quadratic and cubic nonlinear terms in the temporal problem can, depending on the selected range of system parameters, vary widely and take positive and negative values, and thus change the number and stability of equilibrium positions as well as the system behavior which can be a hardening or softening type. The harmonic balance and, for comparison purposes, the method of multiple-scales are used to obtain approximate analytical solution for the primary resonance response and its stability. The obtained primary frequency response results are presented over a selected range of system parameters near and away from veering points which show a significant change in response behavior. The obtained approximate-analytical results were compared with those obtained numerically.
- 12 March 2010
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 16 (6) , 853-877
Primary Resonance Response of a Beam with a Differential Edge Settlement Attached to an Elastic Foundation
In this work, we study, through one-mode simplification, the influence of frequency curve veering on the primary resonance response of an elastic Euler-Bernoulli attached to a linear Winkler elastic foundation. The beam is a hinged-hinged with one torsional spring at one end, has an initial 1/4 sine deflection shape due to a constant differential edge settlement and is subjected to a uniformly distributed vertical load which is harmonically varying with a time part and a large mean part. A combined numerical-analytical procedure which accounts for the nonlinear interdependence between the vertical deflection and induced axial force due to mid-plane stretching was used to determine the beam static deflection. The assumed single mode approach is used to obtain the reduced nonlinear temporal equation of motion about the static equilibrium deflection which contains quadratic and cubic nonlinear terms. The results of numerical simulation indicate that the coefficients of the quadratic and cubic nonlinear terms in the temporal problem can, depending on the selected range of system parameters, vary widely and take positive and negative values, and thus change the number and stability of equilibrium positions as well as the system behavior which can be a hardening or softening type. The harmonic balance and, for comparison purposes, the method of multiple-scales are used to obtain approximate analytical solution for the primary resonance response and its stability. The obtained primary frequency response results are presented over a selected range of system parameters near and away from veering points which show a significant change in response behavior. The obtained approximate-analytical results were compared with those obtained numerically.
- 10 November 2008
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 30 (4) , 427-444
Dynamics of a rotating beam with flexible root and flexible hub
- 10 November 2008
- Published by Techno-Press in STRUCTURAL ENGINEERING AND MECHANICS
- Vol. 30 (4) , 427-444
Dynamics of a rotating beam with flexible root and flexible hub
- 1 January 2008
- Published by ACTA Press in International Journal of Modelling and Simulation
- Vol. 28 (3)
INFLUENCE OF CRACK DEPTH AND ATTACHED MASSES ON BEAM NATURAL FREQUENCIES
- 1 January 2008
- Published by ACTA Press in International Journal of Modelling and Simulation
- Vol. 28 (3)
INFLUENCE OF CRACK DEPTH AND ATTACHED MASSES ON BEAM NATURAL FREQUENCIES
- 1 January 2008
- Published by Taylor & Francis in International Journal of Modelling and Simulation
- Vol. 28 (3) , 239-247
Influence of Crack Depth and Attached Masses on Beam Natural Frequencies
A mathematical model describing the lateral free vibration of a clamped—clamped cracked beam carrying concentrated masses is derived. The masses are assumed small relative to the beam mass; also, the beam is assumed continuous with uniformly distributed properties. The attached masses are modelled as point masses with negligible rotary inertia, and the crack is simulated by a torsional spring. The Lagrangian dynamics, in conjunction with the assumed mode method are used in deriving the equation of motion. The effect of the locations of the attached masses and depth of the crack on the system frequency change is investigated along with the interaction between the attached masses and the crack depth. This interaction appears as a nonlinear coupling term in the natural frequency equation of the system. It is found that the coupling term may be used as an indicator of the error in relating system frequency change to crack only. Verification is carried out using three-dimensional finite element analysis.
- 1 January 2008
- Published by Taylor & Francis in International Journal of Modelling and Simulation
- Vol. 28 (3) , 239-247
Influence of Crack Depth and Attached Masses on Beam Natural Frequencies
A mathematical model describing the lateral free vibration of a clamped—clamped cracked beam carrying concentrated masses is derived. The masses are assumed small relative to the beam mass; also, the beam is assumed continuous with uniformly distributed properties. The attached masses are modelled as point masses with negligible rotary inertia, and the crack is simulated by a torsional spring. The Lagrangian dynamics, in conjunction with the assumed mode method are used in deriving the equation of motion. The effect of the locations of the attached masses and depth of the crack on the system frequency change is investigated along with the interaction between the attached masses and the crack depth. This interaction appears as a nonlinear coupling term in the natural frequency equation of the system. It is found that the coupling term may be used as an indicator of the error in relating system frequency change to crack only. Verification is carried out using three-dimensional finite element analysis.
- 5 July 2007
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 305 (4-5) , 772-782
Subharmonic resonance and transition to chaos of nonlinear oscillators with a combined softening and hardening nonlinearities
- 5 July 2007
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 305 (4-5) , 772-782
Subharmonic resonance and transition to chaos of nonlinear oscillators with a combined softening and hardening nonlinearities
- Open Access
- 7 November 2005
- Published by Wiley in Shock and Vibration
- Vol. 13 (6) , 577-593
Dynamic Model of a Rotating Flexible Arm‐Flexible Root Mechanism Driven by a Shaft Flexible in Torsion
This paper presents a dynamic model of a rotating flexible beam carrying a payload at its tip. The model accounts for the driving shaft and the arm root flexibilities. The finite element method and the Lagrangian dynamics are used in deriving the equations of motion with the small deformation theory assumptions and the Euler‐Bernoulli beam theory. The obtained model is a nonlinear‐coupled system of differential equations. The model is simulated for different combinations of shaft and root flexibilities and arm properties. The simulation results showed that the root flexibility is an important factor that should be considered in association with the arm and shaft flexibilities, as its dynamics influence the motor motion. Moreover, the effect of system non‐linearity on the dynamic behavior is investigated by simulating the equivalent linearized system and it was found to be an important factor that should be considered, particularly when designing a control strategy for practical implementation.
- 7 November 2005
- Published by Wiley in Shock and Vibration
- Vol. 13 (6) , 577-593
Open AccessDynamic Model of a Rotating Flexible Arm‐Flexible Root Mechanism Driven by a Shaft Flexible in Torsion
This paper presents a dynamic model of a rotating flexible beam carrying a payload at its tip. The model accounts for the driving shaft and the arm root flexibilities. The finite element method and the Lagrangian dynamics are used in deriving the equations of motion with the small deformation theory assumptions and the Euler‐Bernoulli beam theory. The obtained model is a nonlinear‐coupled system of differential equations. The model is simulated for different combinations of shaft and root flexibilities and arm properties. The simulation results showed that the root flexibility is an important factor that should be considered in association with the arm and shaft flexibilities, as its dynamics influence the motor motion. Moreover, the effect of system non‐linearity on the dynamic behavior is investigated by simulating the equivalent linearized system and it was found to be an important factor that should be considered, particularly when designing a control strategy for practical implementation.
- 12 October 2004
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 282 (3-5) , 1065-1083
Stability analysis of rotating blade bending vibration due to torsional excitation
- 12 October 2004
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 282 (3-5) , 1065-1083
Stability analysis of rotating blade bending vibration due to torsional excitation