Istvan Farkas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Istvan Farkas has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Attila Bai
Institute of Applied Economics, Faculty of Economics and Business, University of Debrecen, H-4032 Debrecen, Hungary
2 shared publications - Béla Pályi
University of Pannonia
2 shared publications - Henrik Zsiborács
Renewable Energy Research Group, University Center for Circular Economy, University of Pannonia Nagykanizsa, University of Pannonia, Nagykanizsa, Hungary
2 shared publications - József Popp
John Von Neumann University, Kecskemét, Hungary
2 shared publications - Nóra Hegedűsné Baranyai
Renewable Energy Research Group, Soós Ernő Research and Development Center, University Center for Circular Economy, University of Pannonia Nagykanizsa, 8800 Nagykanizsa, Hungary
2 shared publications - Zoltán Gabnai
Institute of Applied Economics, Faculty of Economics and Business, University of Debrecen, 4032 Debrecen, Hungary
2 shared publications
Latest Publications
- 20 September 2020
- Published by Springer Nature
- p. 111-124
Reliability Assessment of PV Modules
- Open Access
- 1 January 2020
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 48 (3) , 701-706
Heat transfer analysis in the chimney of the indirect solar dryer under natural convection mode
An attempt is established to investigate the heat transfer from a heated chimney of an indirect solar dryer and predicted the chimney outlet temperature using energy balance equation. Tests were carried out with no-load condition under natural convection mode. Data of air velocity, temperatures, ambient relative humidity and solar radiation of the drying process are presented in order to solve the heat transfer coefficients. The result shows that temperature difference between mean air inside a chimney and ambient was 23.8 °C at maximum solar radiation of 812 W/m², where maximum airflow is observed. The predicted chimney outlet temperature was found in good agreement with that of the experimental value. Temperature variation, correlation coefficient, and average absolute error are less than 10%, 0.977, and 5%, respectively. Replacing the normal chimney by heated chimney can significantly reduce the heat loss and increase the chimney efficiency.
- 1 January 2020
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 48 (3) , 701-706
Open AccessHeat transfer analysis in the chimney of the indirect solar dryer under natural convection mode
An attempt is established to investigate the heat transfer from a heated chimney of an indirect solar dryer and predicted the chimney outlet temperature using energy balance equation. Tests were carried out with no-load condition under natural convection mode. Data of air velocity, temperatures, ambient relative humidity and solar radiation of the drying process are presented in order to solve the heat transfer coefficients. The result shows that temperature difference between mean air inside a chimney and ambient was 23.8 °C at maximum solar radiation of 812 W/m², where maximum airflow is observed. The predicted chimney outlet temperature was found in good agreement with that of the experimental value. Temperature variation, correlation coefficient, and average absolute error are less than 10%, 0.977, and 5%, respectively. Replacing the normal chimney by heated chimney can significantly reduce the heat loss and increase the chimney efficiency.
- Open Access
- 12 November 2019
- Published by Walter de Gruyter GmbH in Acta Technologica Agriculturae
- Vol. 22 (4) , 128-133
Mathematical Modelling of Solar Thermal Collectors and Storages
Block-oriented modelling is a powerful tool in system design. The models developed this way can be used to study various systems, such as solar thermal systems. In the work presented, main goal is to compare different mathematical models of solar thermal devices. The difference in accuracy of such models in respect to the possibilities of a hardware-in-the-loop simulation will be discussed. Two models of solar thermal collectors will be compared and used in a system containing two different heat storages in order to study the behaviour of these models. The tests were carried out in a Simulink based block-oriented environment called SimSolar.
- 12 November 2019
- Published by Walter de Gruyter GmbH in Acta Technologica Agriculturae
- Vol. 22 (4) , 128-133
Open AccessMathematical Modelling of Solar Thermal Collectors and Storages
Block-oriented modelling is a powerful tool in system design. The models developed this way can be used to study various systems, such as solar thermal systems. In the work presented, main goal is to compare different mathematical models of solar thermal devices. The difference in accuracy of such models in respect to the possibilities of a hardware-in-the-loop simulation will be discussed. Two models of solar thermal collectors will be compared and used in a system containing two different heat storages in order to study the behaviour of these models. The tests were carried out in a Simulink based block-oriented environment called SimSolar.
- 11 September 2018
- Published by Taylor & Francis in Drying Technology
- Vol. 37 (5) , 546-558
Thermal efficiency of vertical and horizontal-finned solar collector integrated with forced air circulation dryer for Apple as a sample
In this article, an experimental estimation of thermal efficiency of horizontal and vertical-finned double-pass solar air collectors integrated with drying chamber has been carried out. The rig consists of two main parts as solar collector and dryer. The system was installed in the laboratory of Szent István University, Gödöllő, Hungary. The absorbers were made from a copper integrated fins in horizontal and vertical directions. The test results showed that the daily efficiency increased by10% when the direction of fins have been changed from vertical to horizontal. After 5 h drying of 2 kg apple slices, the final weights were 1.16 and 1.37 kg by using horizontal and vertical-finned collectors, respectively.
- 11 September 2018
- Published by Taylor & Francis in Drying Technology
- Vol. 37 (5) , 546-558
Thermal efficiency of vertical and horizontal-finned solar collector integrated with forced air circulation dryer for Apple as a sample
In this article, an experimental estimation of thermal efficiency of horizontal and vertical-finned double-pass solar air collectors integrated with drying chamber has been carried out. The rig consists of two main parts as solar collector and dryer. The system was installed in the laboratory of Szent István University, Gödöllő, Hungary. The absorbers were made from a copper integrated fins in horizontal and vertical directions. The test results showed that the daily efficiency increased by10% when the direction of fins have been changed from vertical to horizontal. After 5 h drying of 2 kg apple slices, the final weights were 1.16 and 1.37 kg by using horizontal and vertical-finned collectors, respectively.
- Open Access
Comparison of Thermal Models for Ground-Mounted South-Facing Photovoltaic Technologies: A Practical Case Study
This paper examines the thermal properties of free-standing, ground-installed, south-facing crystalline and amorphous silicon photovoltaic modules, the remaining energy and the energy generation of the modules, in ideal and actual summer weather conditions. This work studies the algorithms in other studies used to describe the thermal processes occurring on the surface of photovoltaic modules. Using accurate devices and real, measured data, the deviations and the inaccuracies of theoretical approaches are investigated. The emphasis of the present study is to improve the simulation accuracy of the total emitted long-wave radiation at the module surface and to show the appropriate overall convection coefficient values for ground-mounted south-facing photovoltaic technologies. The innovative aspect of the present paper is an improved model resulting from an improved convective heat transfer and net long-wave radiation calculation. As a result of this research, algorithms describing the energy fluxes were developed. These algorithms have a 1–3% better accuracy of the net long-wave radiation calculations at the module surface. The rate of net energy exchange by convection at the module surface could be improved by 10–12% compared to the previous literature.
Open AccessComparison of Thermal Models for Ground-Mounted South-Facing Photovoltaic Technologies: A Practical Case Study
This paper examines the thermal properties of free-standing, ground-installed, south-facing crystalline and amorphous silicon photovoltaic modules, the remaining energy and the energy generation of the modules, in ideal and actual summer weather conditions. This work studies the algorithms in other studies used to describe the thermal processes occurring on the surface of photovoltaic modules. Using accurate devices and real, measured data, the deviations and the inaccuracies of theoretical approaches are investigated. The emphasis of the present study is to improve the simulation accuracy of the total emitted long-wave radiation at the module surface and to show the appropriate overall convection coefficient values for ground-mounted south-facing photovoltaic technologies. The innovative aspect of the present paper is an improved model resulting from an improved convective heat transfer and net long-wave radiation calculation. As a result of this research, algorithms describing the energy fluxes were developed. These algorithms have a 1–3% better accuracy of the net long-wave radiation calculations at the module surface. The rate of net energy exchange by convection at the module surface could be improved by 10–12% compared to the previous literature.
- Open Access
- 2 May 2018
- Published by MDPI AG in Sustainability
- Vol. 10 (5) , 1394
Change of Real and Simulated Energy Production of Certain Photovoltaic Technologies in Relation to Orientation, Tilt Angle and Dual-Axis Sun-Tracking. A Case Study in Hungary
The aim of the study is to compare the tilt angle-orientation and dual-axis tracking characteristics of mono- (m-Si), polycrystalline (p-Si), and amorphous silicon (a-Si) modules in the summer of 2017, under real meteorological conditions with simulated data. The most important new element of our study is that, besides a comparison of the three most significant photovoltaic types, the technologies are differentiated by examining specific energy generation using dual-axis tracking and four different orientations at 5-degree intervals compared to simulated values, near to the summer solstice. For these types of measurements, as far as we are aware, there is no previous reliable, well-supported, comparative data. The simulated data show less accurate results, proving the importance of real data. Based on simulated data, the tilt angle and orientation showed about 10% favorable values compared to reality. Knowing our results can make it easier to plan investment, and estimate the investment and operational costs and their return on crystalline and amorphous silicon solar modules, for both sun-tracking and fixed systems with various orientations and tilt angles.
- 2 May 2018
- Published by MDPI AG in Sustainability
- Vol. 10 (5) , 1394
Open AccessChange of Real and Simulated Energy Production of Certain Photovoltaic Technologies in Relation to Orientation, Tilt Angle and Dual-Axis Sun-Tracking. A Case Study in Hungary
The aim of the study is to compare the tilt angle-orientation and dual-axis tracking characteristics of mono- (m-Si), polycrystalline (p-Si), and amorphous silicon (a-Si) modules in the summer of 2017, under real meteorological conditions with simulated data. The most important new element of our study is that, besides a comparison of the three most significant photovoltaic types, the technologies are differentiated by examining specific energy generation using dual-axis tracking and four different orientations at 5-degree intervals compared to simulated values, near to the summer solstice. For these types of measurements, as far as we are aware, there is no previous reliable, well-supported, comparative data. The simulated data show less accurate results, proving the importance of real data. Based on simulated data, the tilt angle and orientation showed about 10% favorable values compared to reality. Knowing our results can make it easier to plan investment, and estimate the investment and operational costs and their return on crystalline and amorphous silicon solar modules, for both sun-tracking and fixed systems with various orientations and tilt angles.
- 3 September 2017
- Published by Springer Nature
- p. 218-226
Design Aspects of Building Integrated Solar Tile Collectors
- 3 September 2017
- Published by Springer Nature
- p. 218-226
Design Aspects of Building Integrated Solar Tile Collectors
- Open Access
- 8 May 2017
- Published by Taylor & Francis in Drying Technology
- Vol. 35 (8) , 905
Papers from the 5th European Drying Conference (EuroDrying 2015)
(2017). Papers from the 5th European Drying Conference (EuroDrying 2015) Drying Technology: Vol. 35, Selected Papers from EuroDrying 2015, pp. 905-905.
- 8 May 2017
- Published by Taylor & Francis in Drying Technology
- Vol. 35 (8) , 905
Open AccessPapers from the 5th European Drying Conference (EuroDrying 2015)
(2017). Papers from the 5th European Drying Conference (EuroDrying 2015) Drying Technology: Vol. 35, Selected Papers from EuroDrying 2015, pp. 905-905.
- 18 September 2014
- Published by Springer Nature in Springer Proceedings in Energy
- p. 349-359
New Priorities in Solar Photovoltaic Applications
- 18 September 2014
- Published by Springer Nature in Springer Proceedings in Energy
- p. 349-359
New Priorities in Solar Photovoltaic Applications
- 10 June 2013
- Published by Taylor & Francis in Drying Technology
- Vol. 31 (8) , 866-871
Integrated Use of Solar Energy for Crop Drying
Various factors such as energy efficiency, the quality of end-products, and environmental aspects have to be taken into account during the drying of agricultural produce. During the recent past, several new approaches for the application of solar dryers to drying various biological materials were developed. In this paper, the background of solar drying, current solar drying practices, and drying of biological products such as grain, fruit, vegetables, hay, etc., are discussed. Additionally, an integrated energy/technology approach in order to maximize solar energy usage and thereby meet the drying requirements has been introduced. This will aid in achieving a sophisticated solution for drying process control, as well.
- 10 June 2013
- Published by Taylor & Francis in Drying Technology
- Vol. 31 (8) , 866-871
Integrated Use of Solar Energy for Crop Drying
Various factors such as energy efficiency, the quality of end-products, and environmental aspects have to be taken into account during the drying of agricultural produce. During the recent past, several new approaches for the application of solar dryers to drying various biological materials were developed. In this paper, the background of solar drying, current solar drying practices, and drying of biological products such as grain, fruit, vegetables, hay, etc., are discussed. Additionally, an integrated energy/technology approach in order to maximize solar energy usage and thereby meet the drying requirements has been introduced. This will aid in achieving a sophisticated solution for drying process control, as well.