Rainer Kaesmaier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Rainer Kaesmaier has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
A. Chalupka
IMS Nanofabrication GmbH (Austria)
2 shared publicationsAndreas Wolter
Infineon Technologies AG (Germany)
2 shared publicationsHans Loeschner
IMS Nanofabrication GmbH (Austria)
2 shared publicationsA. A. MacDowell
1 shared publicationA. A. Mondelli
1 shared publicationA. Stanishevsky
1 shared publication
Latest Publications
- 16 August 2002
- Published by SPIE-Intl Soc Optical Eng
- Vol. 4764, 23-32
Measures to achieve 20nm IPL stencil mask distortion
From detailed comparisons of stencil mask distortion measurements with Finite Element (FE) analyses the parameters of influence are well known. Most of them are under control of the mask manufacturer, such as the membrane stress level and the etching process. By means of FE analysis the different contributions may be classified. Some of the errors can be reduced if more stringent specifications of the SOI wafer are fulfilled, some of them may be reduced after pre-calculation. Reduction of the remaining placement errors can be achieved if specific means of an Ion Projection Lithography (IPL) tool are applied. These are mainly magnification and anamorphic corrections removing so-called global distortions. The remaining local distortions can be further reduced by applying the concept of thermal mask adjustment (THEMA).
- 16 August 2002
- Published by SPIE-Intl Soc Optical Eng
- Vol. 4764, 23-32
Measures to achieve 20nm IPL stencil mask distortion
From detailed comparisons of stencil mask distortion measurements with Finite Element (FE) analyses the parameters of influence are well known. Most of them are under control of the mask manufacturer, such as the membrane stress level and the etching process. By means of FE analysis the different contributions may be classified. Some of the errors can be reduced if more stringent specifications of the SOI wafer are fulfilled, some of them may be reduced after pre-calculation. Reduction of the remaining placement errors can be achieved if specific means of an Ion Projection Lithography (IPL) tool are applied. These are mainly magnification and anamorphic corrections removing so-called global distortions. The remaining local distortions can be further reduced by applying the concept of thermal mask adjustment (THEMA).
- 30 June 2000
- Published by Elsevier in Microelectronic Engineering
- Vol. 53 (1) , 37-45
Ion Projection Lithography: Progress of European MEDEA & International Program
- 30 June 2000
- Published by Elsevier in Microelectronic Engineering
- Vol. 53 (1) , 37-45
Ion Projection Lithography: Progress of European MEDEA & International Program
- 1 November 1999
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 17 (6) , 3091-3097
Ion projection lithography: International development program
Ion projection lithography (IPL) has demonstrated not only the resolution required for next-generation lithography (50 nm resolution at >4:1 aspect ratio) [Bruenger et al., Microelectron Eng. 46, 477 (1999)] but also cost advantages with respect to other competing technologies [Gross et al., J. Vac. Sci. Technol. B 16, 3150 (1998)]. This article reports on the progress of a worldwide development program, with the target to manufacture a process development tool and create the necessary mask infrastructure to demonstrate that IPL is a viable industrial lithography technology for the future. An overview of papers, reporting on the progress in critical areas, is given and new, experimentally validated, simulations of complementary mask stitching are shown for the first time. Longitudinal and lateral offsets of up to 32 nm for 100 nm critical dimensions are possible with linewidth variations less than 11 nm. Our concept for beta tools, based on a powerful new stitcher strategy, is described. This will lead to a high-throughput tool for manufacturing integrated-circuit generations with minimum feature sizes of 50 nm and, possibly, below.
- 1 November 1999
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 17 (6) , 3091-3097
Ion projection lithography: International development program
Ion projection lithography (IPL) has demonstrated not only the resolution required for next-generation lithography (50 nm resolution at >4:1 aspect ratio) [Bruenger et al., Microelectron Eng. 46, 477 (1999)] but also cost advantages with respect to other competing technologies [Gross et al., J. Vac. Sci. Technol. B 16, 3150 (1998)]. This article reports on the progress of a worldwide development program, with the target to manufacture a process development tool and create the necessary mask infrastructure to demonstrate that IPL is a viable industrial lithography technology for the future. An overview of papers, reporting on the progress in critical areas, is given and new, experimentally validated, simulations of complementary mask stitching are shown for the first time. Longitudinal and lateral offsets of up to 32 nm for 100 nm critical dimensions are possible with linewidth variations less than 11 nm. Our concept for beta tools, based on a powerful new stitcher strategy, is described. This will lead to a high-throughput tool for manufacturing integrated-circuit generations with minimum feature sizes of 50 nm and, possibly, below.