G. Gary
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
G. Gary has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Bengt Lundberg
The Angström Laboratory, Uppsala University, Box 534, SE-751 21 Uppsala, Sweden
2 shared publications - Dirk Mohr
Department of Mechanical and Process Engineering, ETH Zurich, Zurich, Switzerland
1 shared publication M. N. Bissac
Laboratoire de Physique Théorique, UMR 7644, École Polytechnique, 91128 Palaiseau, France
1 shared publicationP. Collet
Laboratoire de Physique Théorique, UMR 7644, École Polytechnique, 91128 Palaiseau, France
1 shared publication- Pierre Collet
Ecole polytechnique CNRS Institut polytechnique de Paris route de Saclay 91128 Palaiseau Cedex- France
1 shared publication - Ramzi Othman
Mechanical Engineering Department, Faculty of Engineering King Abdulaziz University Jeddah Saudi Arabia
1 shared publication
Latest Publications
- 19 November 2012
- Published by Wiley in Journal of Applied Mechanics
- Vol. 80 (1) , 011018
Noise-Corrected Estimation of Complex Modulus in Accord With Causality and Thermodynamics: Application to an Impact Test
Methods for estimation of the complex modulus generally produce data from which discrete results can be obtained for a set of frequencies. As these results are normally afflicted by noise, they are not necessarily consistent with the principle of causality and requirements of thermodynamics. A method is established for noise-corrected estimation of the complex modulus, subject to the constraints of causality, positivity of dissipation rate and reality of relaxation function, given a finite set of angular frequencies and corresponding complex moduli obtained experimentally. Noise reduction is achieved by requiring that two self-adjoint matrices formed from the experimental data should be positive semidefinite. The method provides a rheological model that corresponds to a specific configuration of springs and dashpots. The poles of the complex modulus on the positive imaginary frequency axis are determined by a subset of parameters obtained as the common positive zeros of certain rational functions, while the remaining parameters are obtained from a least squares fit. If the set of experimental data is sufficiently large, the level of refinement of the rheological model is in accordance with the material behavior and the quality of the experimental data. The method was applied to an impact test with a Nylon bar specimen. In this case, data at the 29 lowest resonance frequencies resulted in a rheological model with 14 parameters. The method has added improvements to the identification of rheological models as follows: (1) Noise reduction is fully integrated. (2) A rheological model is provided with a number of elements in accordance with the complexity of the material behavior and the quality of the experimental data. (3) Parameters determining poles of the complex modulus are obtained without use of a least squares fit.
- 19 November 2012
- Published by Wiley in Journal of Applied Mechanics
- Vol. 80 (1) , 011018
Noise-Corrected Estimation of Complex Modulus in Accord With Causality and Thermodynamics: Application to an Impact Test
Methods for estimation of the complex modulus generally produce data from which discrete results can be obtained for a set of frequencies. As these results are normally afflicted by noise, they are not necessarily consistent with the principle of causality and requirements of thermodynamics. A method is established for noise-corrected estimation of the complex modulus, subject to the constraints of causality, positivity of dissipation rate and reality of relaxation function, given a finite set of angular frequencies and corresponding complex moduli obtained experimentally. Noise reduction is achieved by requiring that two self-adjoint matrices formed from the experimental data should be positive semidefinite. The method provides a rheological model that corresponds to a specific configuration of springs and dashpots. The poles of the complex modulus on the positive imaginary frequency axis are determined by a subset of parameters obtained as the common positive zeros of certain rational functions, while the remaining parameters are obtained from a least squares fit. If the set of experimental data is sufficiently large, the level of refinement of the rheological model is in accordance with the material behavior and the quality of the experimental data. The method was applied to an impact test with a Nylon bar specimen. In this case, data at the 29 lowest resonance frequencies resulted in a rheological model with 14 parameters. The method has added improvements to the identification of rheological models as follows: (1) Noise reduction is fully integrated. (2) A rheological model is provided with a number of elements in accordance with the complexity of the material behavior and the quality of the experimental data. (3) Parameters determining poles of the complex modulus are obtained without use of a least squares fit.
- 15 September 2009
- Published by EDP Sciences
- Vol. 1, 485-490
Theoretical assessment of stress-strain curve estimates in Split Hopkinson Bar experiments
- 15 September 2009
- Published by EDP Sciences
- Vol. 1, 485-490
Theoretical assessment of stress-strain curve estimates in Split Hopkinson Bar experiments
- 1 September 2003
- Published by EDP Sciences in Journal de Physique IV
- Vol. 110, 397-404
Testing with SHPB from quasi-static to dynamic strain rates
- 1 September 2003
- Published by EDP Sciences in Journal de Physique IV
- Vol. 110, 397-404
Testing with SHPB from quasi-static to dynamic strain rates