A. Degen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
A. Degen has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
E. Sossna
Institute of Technological Physics, IMA, University of Kassel, Heinrich-Plett-Strasse 40, 34132-Kassel, Germany
2 shared publicationsP. Hudek
Slovak Academy of Sciences, Dubravska 9, 842 20 Bratislava, Slovak Republic
2 shared publicationsA. Ehrmann
SIEMENS AG, Munich and Erlangen, Germany
1 shared publicationAlex R. Shimkunas
1 shared publicationD. C. Flanders
1 shared publicationE. Haugeneder
IMS-Ionen Mikrofabrikations Systeme GmbH, Vienna, Austria
1 shared publication
Latest Publications
- 1 November 2001
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 19 (6) , 2665-2670
Mechanical, geometrical, and electrical characterization of silicon membranes for open stencil masks
Silicon membranes are used for stencil masks which are key to charged particle projection lithography, particularly for ion projection lithography, electron beam projection. Quantitative and qualitative determination of the mechanical properties of the true thickness, thickness variations (morphology), electrical conductivity and stress is critical to the development of next generation lithography. The metrology setup includes high accuracy thickness, refractive index and electrical conductivity measurement based on infrared variable angle spectroscopic ellipsometry, thickness variation characterization based on the Fizeau interferometric scheme and mechanical stress evaluation based on a novel double bulging technique.
- 1 November 2001
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 19 (6) , 2665-2670
Mechanical, geometrical, and electrical characterization of silicon membranes for open stencil masks
Silicon membranes are used for stencil masks which are key to charged particle projection lithography, particularly for ion projection lithography, electron beam projection. Quantitative and qualitative determination of the mechanical properties of the true thickness, thickness variations (morphology), electrical conductivity and stress is critical to the development of next generation lithography. The metrology setup includes high accuracy thickness, refractive index and electrical conductivity measurement based on infrared variable angle spectroscopic ellipsometry, thickness variation characterization based on the Fizeau interferometric scheme and mechanical stress evaluation based on a novel double bulging technique.
- 24 August 2001
- Published by Elsevier in Microelectronic Engineering
- Vol. 57-58, 425-432
Stress analysis in Si membranes for open stencil masks and mini-reticles using double bulging and resonance methods
- 24 August 2001
- Published by Elsevier in Microelectronic Engineering
- Vol. 57-58, 425-432
Stress analysis in Si membranes for open stencil masks and mini-reticles using double bulging and resonance methods
- 1 November 1999
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 17 (6) , 3127-3131
Directly sputtered stress-compensated carbon protective layer for silicon stencil masks
Silicon stencil masks for ion beam projection lithography have a protective layer stopping the ions and thus preventing a change in the Si membrane stress. This is needed to maintain extremely tight pattern placement specifications even when they are irradiated with high exposure doses. The fabrication of carbon protective layers by indirect sputter coating which are suitable for helium ion beam exposure has already been reported. This article describes a method of forming very low stress carbon protective layers based on direct radio frequency sputter coating with nitrogen added to the argon sputter gas and in situ thermal treatment using commercially available equipment. The carbon layers thus produced are stable in conventional environments. The article deals also with the physical characterization of carbon layers and the protection performances of these coatings under helium ion beam exposure using accelerated lifetime testing.
- 1 November 1999
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B: Microelectronics and Nanometer Structures Processing, Measurement, and Phenomena
- Vol. 17 (6) , 3127-3131
Directly sputtered stress-compensated carbon protective layer for silicon stencil masks
Silicon stencil masks for ion beam projection lithography have a protective layer stopping the ions and thus preventing a change in the Si membrane stress. This is needed to maintain extremely tight pattern placement specifications even when they are irradiated with high exposure doses. The fabrication of carbon protective layers by indirect sputter coating which are suitable for helium ion beam exposure has already been reported. This article describes a method of forming very low stress carbon protective layers based on direct radio frequency sputter coating with nitrogen added to the argon sputter gas and in situ thermal treatment using commercially available equipment. The carbon layers thus produced are stable in conventional environments. The article deals also with the physical characterization of carbon layers and the protection performances of these coatings under helium ion beam exposure using accelerated lifetime testing.