Jean H. Prevost
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jean H. Prevost has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Fabien Georget
Institute of Building Materials Research, RWTH Aachen University, Aachen, Germany
2 shared publications - James K. Guest
Johns Hopkins University, Baltimore, MD
2 shared publications - Allan M. Rubin
Department of Geosciences Princeton University Princeton New Jersey USA
1 shared publication George Deodatis
Department of Civil and Environmental Engineering, Princeton University, Princeton, NJ 08544, U.S.A.
1 shared publicationImene R. Goumiri
Department of Civil and Environmental Engineering, Princeton University, Princeton, NJ 08544, U.S.A.
1 shared publication- Imène R. Goumiri
Lawrence Livermore National Laboratory 94551 Livermore CA USA
1 shared publication
Latest Publications
- 6 July 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 1992-1999
Intersecting Faults Simulation for Three-Dimensional Reservoir-Geomechanical Models
Faults are geological entities with thicknesses (of the order cm) several orders of magnitude smaller than the grid blocks (of the order 10 m) typically used to discretize reservoir and/or over-under-burden geological formations. Introducing faults in a complex reservoir and/or geomechanical mesh therefore poses significant meshing difficulties. In this paper, we introduce faults in the mesh without meshing them explicitly, by using the extended finite element method (X-FEM) in which the nodes whose basis function support intersects the fault are enriched within the framework of partition of unity. For the geomechanics, the fault is treated as an internal displacement discontinuity that allows slipping to occur using a Mohr-Coulomb type criterion. For the reservoir, the fault is either an internal fluid flow conduit that allows fluid flow in the fault as well as to enter/leave the fault or is a barrier to flow (sealing fault). Equal-order displacement and pressure approximations are used. Two- and three-dimensional benchmark computations are presented to verify the accuracy of the approach, and simulations are presented that reveal the influence of the rate of loading on the activation of faults.
- 6 July 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 1992-1999
Intersecting Faults Simulation for Three-Dimensional Reservoir-Geomechanical Models
Faults are geological entities with thicknesses (of the order cm) several orders of magnitude smaller than the grid blocks (of the order 10 m) typically used to discretize reservoir and/or over-under-burden geological formations. Introducing faults in a complex reservoir and/or geomechanical mesh therefore poses significant meshing difficulties. In this paper, we introduce faults in the mesh without meshing them explicitly, by using the extended finite element method (X-FEM) in which the nodes whose basis function support intersects the fault are enriched within the framework of partition of unity. For the geomechanics, the fault is treated as an internal displacement discontinuity that allows slipping to occur using a Mohr-Coulomb type criterion. For the reservoir, the fault is either an internal fluid flow conduit that allows fluid flow in the fault as well as to enter/leave the fault or is a barrier to flow (sealing fault). Equal-order displacement and pressure approximations are used. Two- and three-dimensional benchmark computations are presented to verify the accuracy of the approach, and simulations are presented that reveal the influence of the rate of loading on the activation of faults.
- 6 July 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 672-680
Integration of a Microstructural Model in a Coupled Reactive Transport Simulation of Carbonation and Drying
To guarantee the durability of new cement and concrete formulations, we need to understand the long-term degradation mechanisms and how they relate to the evolution of the microstructure. Inside a porous medium, the different phenomena are coupled by the microstructure and its evolution. For example, in coupled simulation of drying and carbonation, the entry of CO2 and release of water will occur through the carbonated layer which has distinct properties from the non-carbonated core. To solve this problem, we propose a new reactive transport implementation which can integrate a custom-made microstructure model adapted to the problem at hand. This feature has many strong numerical challenges and it leads to a robust and flexible reactive transport framework. We demonstrate its capabilities through coupled carbonation and drying simulation of cement pastes. We show that the water transport properties are key elements in the rate of propagation of the carbonation reaction. To reach quantitative prediction abilities, the capillary pressure and the relative transport properties must be computed accurately in both the carbonated and the non-carbonated layers.
- 6 July 2017
- Published by American Society of Civil Engineers (ASCE)
- p. 672-680
Integration of a Microstructural Model in a Coupled Reactive Transport Simulation of Carbonation and Drying
To guarantee the durability of new cement and concrete formulations, we need to understand the long-term degradation mechanisms and how they relate to the evolution of the microstructure. Inside a porous medium, the different phenomena are coupled by the microstructure and its evolution. For example, in coupled simulation of drying and carbonation, the entry of CO2 and release of water will occur through the carbonated layer which has distinct properties from the non-carbonated core. To solve this problem, we propose a new reactive transport implementation which can integrate a custom-made microstructure model adapted to the problem at hand. This feature has many strong numerical challenges and it leads to a robust and flexible reactive transport framework. We demonstrate its capabilities through coupled carbonation and drying simulation of cement pastes. We show that the water transport properties are key elements in the rate of propagation of the carbonation reaction. To reach quantitative prediction abilities, the capillary pressure and the relative transport properties must be computed accurately in both the carbonated and the non-carbonated layers.
- 1 February 2015
- Published by Elsevier in Cement and Concrete Research
- Vol. 68, 139-147
A speciation solver for cement paste modeling and the semismooth Newton method
- 1 February 2015
- Published by Elsevier in Cement and Concrete Research
- Vol. 68, 139-147
A speciation solver for cement paste modeling and the semismooth Newton method
- 15 March 2013
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 94 (4) , 400-417
New findings on limit state analysis with unstructured triangular finite elements
- 15 March 2013
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 94 (4) , 400-417
New findings on limit state analysis with unstructured triangular finite elements
- 14 April 2011
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 35 (7) , 837-845
Cell to node projections: An assessment of error
Reservoir simulators typically use cell‐centered finite volume schemes and do not model directly the coupling of the flow processes with the geomechanics. Coupling of geomechanics with fluid flow can be important in many cases, but introducing fully coupled geomechanical effects in those simulators is not a trivial issue, because the geomechanics is better done by using the Galerkin vertex‐centered finite element methods by which the solid displacements are computed at the vertices of the cells. This creates difficulties in interfacing cell variables with nodal variables. Uncoupled or loosely coupled models are used by many researchers/practitioners by which a reservoir model is coupled to a geomechanical model by staggering in‐time flow and deformation via a sophisticated interface that repeatedly calls first flow and then mechanics. The method therefore requires projection of the reservoir cell variables onto the nodes of the geomechanics Galerkin finite element mesh.In this note, we attempt to quantify the errors associated with cell to node projection operations. For that purpose, we use a simple model of the pressure equation for a heterogeneous medium in one dimension. We are able to derive theexactanalytical solution for this problem for both nodal and cell pressures. This allows us to compute the errors due to projection analytically, function of meshing refinement and permeability field variations. We compute upper and lower bounds for the errors, and analyze their magnitude for a variety of cases. We conclude that, in general, cell to node projection operations lead to substantial errors. Copyright © 2010 John Wiley & Sons, Ltd.
- 14 April 2011
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 35 (7) , 837-845
Cell to node projections: An assessment of error
Reservoir simulators typically use cell‐centered finite volume schemes and do not model directly the coupling of the flow processes with the geomechanics. Coupling of geomechanics with fluid flow can be important in many cases, but introducing fully coupled geomechanical effects in those simulators is not a trivial issue, because the geomechanics is better done by using the Galerkin vertex‐centered finite element methods by which the solid displacements are computed at the vertices of the cells. This creates difficulties in interfacing cell variables with nodal variables. Uncoupled or loosely coupled models are used by many researchers/practitioners by which a reservoir model is coupled to a geomechanical model by staggering in‐time flow and deformation via a sophisticated interface that repeatedly calls first flow and then mechanics. The method therefore requires projection of the reservoir cell variables onto the nodes of the geomechanics Galerkin finite element mesh.In this note, we attempt to quantify the errors associated with cell to node projection operations. For that purpose, we use a simple model of the pressure equation for a heterogeneous medium in one dimension. We are able to derive theexactanalytical solution for this problem for both nodal and cell pressures. This allows us to compute the errors due to projection analytically, function of meshing refinement and permeability field variations. We compute upper and lower bounds for the errors, and analyze their magnitude for a variety of cases. We conclude that, in general, cell to node projection operations lead to substantial errors. Copyright © 2010 John Wiley & Sons, Ltd.
- 18 March 2011
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 36 (3) , 352-361
The effect of capillary pressure on the saturation equation of two‐phase flow in porous media
SUMMARY: A complete and accurate simulation of two‐phase flow in porous media requires knowledge of all the controlling physics (and values of physical parameters) that play a relevant role and an understanding of the effects of each one on the solution. Of particular concern here is the effect of capillary pressure and the length scale over which it is relevant. The goal of this paper is to provide guidance onto when to include the effects of capillary pressure in the model, and onto what are the resulting length scale restrictions if those effects are to be included. Copyright © 2011 John Wiley & Sons, Ltd.
- 18 March 2011
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 36 (3) , 352-361
The effect of capillary pressure on the saturation equation of two‐phase flow in porous media
SUMMARY: A complete and accurate simulation of two‐phase flow in porous media requires knowledge of all the controlling physics (and values of physical parameters) that play a relevant role and an understanding of the effects of each one on the solution. Of particular concern here is the effect of capillary pressure and the length scale over which it is relevant. The goal of this paper is to provide guidance onto when to include the effects of capillary pressure in the model, and onto what are the resulting length scale restrictions if those effects are to be included. Copyright © 2011 John Wiley & Sons, Ltd.
- 23 June 2008
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 33 (4) , 425-447
Bending of fluid-saturated linear poroelastic beams with compressible constituents
- 23 June 2008
- Published by Wiley in International Journal for Numerical and Analytical Methods in Geomechanics
- Vol. 33 (4) , 425-447
Bending of fluid-saturated linear poroelastic beams with compressible constituents
- 12 December 2005
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 66 (3) , 461-484
Topology optimization of creeping fluid flows using a Darcy–Stokes finite element
- 12 December 2005
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 66 (3) , 461-484
Topology optimization of creeping fluid flows using a Darcy–Stokes finite element
- Top Cited Papers
- 15 July 2004
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 61 (2) , 238-254
Achieving minimum length scale in topology optimization using nodal design variables and projection functions
A methodology for imposing a minimum length scale on structural members in discretized topology optimization problems is described. Nodal variables are implemented as the design variables and are projected onto element space to determine the element volume fractions that traditionally define topology. The projection is made via mesh independent functions that are based upon the minimum length scale. A simple linear projection scheme and a non‐linear scheme using a regularized Heaviside step function to achieve nearly 0–1 solutions are examined. The new approach is demonstrated on the minimum compliance problem and the popular SIMP method is used to penalize the stiffness of intermediate volume fraction elements. Solutions are shown to meet user‐defined length scale criterion without additional constraints, penalty functions or sensitivity filters. No instances of mesh dependence or checkerboard patterns have been observed. Copyright © 2004 John Wiley & Sons, Ltd.
- 15 July 2004
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 61 (2) , 238-254
Top Cited PapersAchieving minimum length scale in topology optimization using nodal design variables and projection functions
A methodology for imposing a minimum length scale on structural members in discretized topology optimization problems is described. Nodal variables are implemented as the design variables and are projected onto element space to determine the element volume fractions that traditionally define topology. The projection is made via mesh independent functions that are based upon the minimum length scale. A simple linear projection scheme and a non‐linear scheme using a regularized Heaviside step function to achieve nearly 0–1 solutions are examined. The new approach is demonstrated on the minimum compliance problem and the popular SIMP method is used to penalize the stiffness of intermediate volume fraction elements. Solutions are shown to meet user‐defined length scale criterion without additional constraints, penalty functions or sensitivity filters. No instances of mesh dependence or checkerboard patterns have been observed. Copyright © 2004 John Wiley & Sons, Ltd.