Daniel Lévesque
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Daniel Lévesque has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
J.-P. Monchalin
National Research Council Canada, 75 de Mortagne Blvd., Boucherville, Quebec J4B 6Y4, Canada
3 shared publicationsM. Lord
National Research Council Canada, 75 de Mortagne Blvd., Boucherville, Quebec J4B 6Y4, Canada
3 shared publicationsC. Bescond
National Research Council Canada, 75 de Mortagne Blvd., Boucherville, Quebec J4B 6Y4, Canada
2 shared publicationsA. Beauchesne
National Research Council Canada, 75 de Mortagne Blvd., Boucherville (Qc), J4B 6Y4, Canada
1 shared publicationAlain Blouin
Industrial Materials Institute, National Research Council of Canada , 75 de Mortagne Boulevard, Boucherville, Québec, Canada , J4B 6Y4
1 shared publication- André Moreau
National Research Council of Canada
1 shared publication
Latest Publications
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1949 (1) , 180001
Further investigation of surface velocity measurements for material characterization in laser shockwave experiments
As part of the U.S. High Performance Research Reactor program, a laser shock test system is being developed by the Idaho National Laboratory (INL) to characterize interface strength in innovative plate fuel for research reactors around the world. The INL has been working with National Research Council Canada (NRC) on this project for the last five years. One of the concerns is the difficulty of calibrating and standardizing the laser shock technique. A recent analytical study and testing support the use of the Hugoniot Elastic Limit (HEL) in materials as a robust and simple benchmark to compare stresses generated by different laser shock systems. Using a non-contact laser velocimeter based on a solid Fabry-Perot etalon, the systems at NRC and INL show that the back-surface velocity reached at the HEL is consistent, and independent of the laser power used. In this work, the laser velocimeter of the NRC system is tested against a fast rotating wheel to verify accuracy and determine best operating conditions. A round robin test between the two laser shock systems on plates of different aluminum alloys is presented that shows the consistent characterization of the aluminum alloys based on the HEL velocities as well as determines the bias between the systems. The effects of setup parameters on other characteristics of the back-surface velocity trace and corresponding stress wave are also discussed.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1949 (1) , 180001
Further investigation of surface velocity measurements for material characterization in laser shockwave experiments
As part of the U.S. High Performance Research Reactor program, a laser shock test system is being developed by the Idaho National Laboratory (INL) to characterize interface strength in innovative plate fuel for research reactors around the world. The INL has been working with National Research Council Canada (NRC) on this project for the last five years. One of the concerns is the difficulty of calibrating and standardizing the laser shock technique. A recent analytical study and testing support the use of the Hugoniot Elastic Limit (HEL) in materials as a robust and simple benchmark to compare stresses generated by different laser shock systems. Using a non-contact laser velocimeter based on a solid Fabry-Perot etalon, the systems at NRC and INL show that the back-surface velocity reached at the HEL is consistent, and independent of the laser power used. In this work, the laser velocimeter of the NRC system is tested against a fast rotating wheel to verify accuracy and determine best operating conditions. A round robin test between the two laser shock systems on plates of different aluminum alloys is presented that shows the consistent characterization of the aluminum alloys based on the HEL velocities as well as determines the bias between the systems. The effects of setup parameters on other characteristics of the back-surface velocity trace and corresponding stress wave are also discussed.
- 1 July 2016
- Published by Elsevier in Ultrasonics
- Vol. 69, 236-242
Inspection of thick welded joints using laser-ultrasonic SAFT
- 1 July 2016
- Published by Elsevier in Ultrasonics
- Vol. 69, 236-242
Inspection of thick welded joints using laser-ultrasonic SAFT
- 1 July 2016
- Published by Elsevier in Ultrasonics
- Vol. 69, 268-272
Anomalous ultrasonic attenuation in ferritic steels at elevated temperatures
- 1 July 2016
- Published by Elsevier in Ultrasonics
- Vol. 69, 268-272
Anomalous ultrasonic attenuation in ferritic steels at elevated temperatures
- Open Access
- 10 February 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706 (1) , 130003
Inspection of additive manufactured parts using laser ultrasonics
Additive manufacturing is a novel technology of high importance for global sustainability of resources. As additive manufacturing involves typically layer-by-layer fusion of the feedstock (wire or powder), an important characteristic of the fabricated metallic structural parts, such as those used in aero-engines, is the performance, which is highly related to the presence of defects, such as cracks, lack of fusion or bonding between layers, and porosity. For this purpose, laser ultrasonics is very attractive due to its non-contact nature and is especially suited for the analysis of parts of complex geometries. In addition, the technique is well adapted to online implementation and real-time measurement during the manufacturing process. The inspection can be performed from either the top deposited layer or the underside of the substrate and the defects can be visualized using laser ultrasonics combined with the synthetic aperture focusing technique (SAFT). In this work, a variety of results obtained off-line on INCONEL® 718 and Ti-6Al-4V coupons that were manufactured using laser powder, laser wire, or electron beam wire deposition are reported and most defects detected were further confirmed by X-ray micro-computed tomography.
- 10 February 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706 (1) , 130003
Open AccessInspection of additive manufactured parts using laser ultrasonics
Additive manufacturing is a novel technology of high importance for global sustainability of resources. As additive manufacturing involves typically layer-by-layer fusion of the feedstock (wire or powder), an important characteristic of the fabricated metallic structural parts, such as those used in aero-engines, is the performance, which is highly related to the presence of defects, such as cracks, lack of fusion or bonding between layers, and porosity. For this purpose, laser ultrasonics is very attractive due to its non-contact nature and is especially suited for the analysis of parts of complex geometries. In addition, the technique is well adapted to online implementation and real-time measurement during the manufacturing process. The inspection can be performed from either the top deposited layer or the underside of the substrate and the defects can be visualized using laser ultrasonics combined with the synthetic aperture focusing technique (SAFT). In this work, a variety of results obtained off-line on INCONEL® 718 and Ti-6Al-4V coupons that were manufactured using laser powder, laser wire, or electron beam wire deposition are reported and most defects detected were further confirmed by X-ray micro-computed tomography.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706, 020019
Non-intrusive measurement of inner bore temperature of small arms using integrated ultrasonic transducers
Management of thermal input to a small arms weapons system is a significant design and operational constraint. A collaborative project was initiated with the objective to measure non-intrusively the inner bore barrel temperature of a small arm during actual firing. The approach uses integrated ultrasonic transducers (IUTs) and the velocity temperature dependence of the longitudinal wave propagating through thickness. IUT is successfully implemented on a small arm at 3 locations and results from several firing tests are presented. The small but systematic increase in ultrasonic time delay of less than 1 ns after each firing shot is reliably measured, in agreement with a simple 1D model of heat conduction, and measured temperature rises are consistent with the thicknesses at the different locations. The evaluation of the peak inner bore temperatures using IUT and their validation using eroding surface thermocouples at the same locations in the barrel are discussed.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1706, 020019
Non-intrusive measurement of inner bore temperature of small arms using integrated ultrasonic transducers
Management of thermal input to a small arms weapons system is a significant design and operational constraint. A collaborative project was initiated with the objective to measure non-intrusively the inner bore barrel temperature of a small arm during actual firing. The approach uses integrated ultrasonic transducers (IUTs) and the velocity temperature dependence of the longitudinal wave propagating through thickness. IUT is successfully implemented on a small arm at 3 locations and results from several firing tests are presented. The small but systematic increase in ultrasonic time delay of less than 1 ns after each firing shot is reliably measured, in agreement with a simple 1D model of heat conduction, and measured temperature rises are consistent with the thicknesses at the different locations. The evaluation of the peak inner bore temperatures using IUT and their validation using eroding surface thermocouples at the same locations in the barrel are discussed.
- 13 July 2011
- Published by Taylor & Francis in Nondestructive Testing and Evaluation
- Vol. 26 (3-4) , 319-333
Laser ultrasonics for defect detection and residual stress measurement of friction stir welds
The laser-ultrasonic technique is investigated for defect detection and sizing as well as for residual stress measurement in welds obtained by friction stir welding (FSW). When combined with the Fourier domain synthetic aperture focusing technique, very good performances are achieved for detecting lack of penetration in butt joints, the detection limit coinciding with the conditions of reduced mechanical properties. Also, the detection of kissing bonds seems to be possible in lap joints when probing with ultrasonic frequencies up to 200 MHz. Residual stresses induced by the FSW process can also be probed by laser ultrasonics. The method is based on monitoring the velocity change of the laser-generated surface skimming longitudinal wave, propagating just below the surface and being found much more sensitive to stress. The residual stress profile measured across the weld line is in good agreement with results from a finite element model and from strain gauge measurements.
- 13 July 2011
- Published by Taylor & Francis in Nondestructive Testing and Evaluation
- Vol. 26 (3-4) , 319-333
Laser ultrasonics for defect detection and residual stress measurement of friction stir welds
The laser-ultrasonic technique is investigated for defect detection and sizing as well as for residual stress measurement in welds obtained by friction stir welding (FSW). When combined with the Fourier domain synthetic aperture focusing technique, very good performances are achieved for detecting lack of penetration in butt joints, the detection limit coinciding with the conditions of reduced mechanical properties. Also, the detection of kissing bonds seems to be possible in lap joints when probing with ultrasonic frequencies up to 200 MHz. Residual stresses induced by the FSW process can also be probed by laser ultrasonics. The method is based on monitoring the velocity change of the laser-generated surface skimming longitudinal wave, propagating just below the surface and being found much more sensitive to stress. The residual stress profile measured across the weld line is in good agreement with results from a finite element model and from strain gauge measurements.
- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7554
Signal processing with unequally spaced data in Fourier-domain optical coherence tomography
Different algorithms for performing Fourier transforms with unequally sampled data in wavenumber space for Fourier-domain optical coherence tomography are considered. The efficiency of these algorithms is evaluated from point-spread functions obtained with a swept-source optical coherence tomography system and from computational time. Images of a 4-layer phantom processed with these different algorithms are compared. We show that convolving the data with an optimized Kaiser-Bessel window allowing a small oversampling factor before computing the fast Fourier transform provides the optimal trade-off between image quality and computational time.
- 11 February 2010
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7554
Signal processing with unequally spaced data in Fourier-domain optical coherence tomography
Different algorithms for performing Fourier transforms with unequally sampled data in wavenumber space for Fourier-domain optical coherence tomography are considered. The efficiency of these algorithms is evaluated from point-spread functions obtained with a swept-source optical coherence tomography system and from computational time. Images of a 4-layer phantom processed with these different algorithms are compared. We show that convolving the data with an optimized Kaiser-Bessel window allowing a small oversampling factor before computing the fast Fourier transform provides the optimal trade-off between image quality and computational time.
- 20 January 2010
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 41 (3) , 744-750
Macroregion Size Measurements in Bimodal Titanium Forgings Using Two-Dimensional Autocorrelation Method
- 20 January 2010
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 41 (3) , 744-750
Macroregion Size Measurements in Bimodal Titanium Forgings Using Two-Dimensional Autocorrelation Method