Hengan Ou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hengan Ou has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Shakir Gatea
Department of Materials Engineering, Faculty of Engineering, University of Kufa, Al-Najaf, Iraq
9 shared publications - Hui Long
Department of Mechanical Engineering, The University of Sheffield, Sheffield, S1 3JD, UK
7 shared publications Bin Lu
Department of Plasticity Technology, Shanghai Jiao Tong University, Shanghai, 200030, China
6 shared publicationsB. Lu
Shanghai Jiao Tong University
4 shared publications- Fei Chen
National Engineering Research Center of Die and Mold CAD, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai, People’s Republic of China
4 shared publications - David Graham McCartney
Department of Mechanical Engineering, University College London, London WC1E 7JE, UK
3 shared publications
Latest Publications
- Open Access
- 9 May 2026
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 180, 107464
Deformation and ductile fracture characterization and modelling of Poly-Ether-Ether-Ketone
- 9 May 2026
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 180, 107464
Open AccessDeformation and ductile fracture characterization and modelling of Poly-Ether-Ether-Ketone
- Open Access
- 26 December 2025
- Published by Springer Nature in International Journal of Material Forming
- Vol. 19 (1) , 4
Characterisation and modelling of ductile fracture in incremental sheet forming of an aluminium alloy with consideration of temperature variations
Although extensive studies have been conducted to predict ductile fracture at room temperature, no attempt has been made to use Gurson–Tvergaard–Needleman (GTN) model to capture the effect of temperature due to spindle speed induced friction heat on damage accumulation in incremental sheet forming (ISF). In this work, the temperature effect is incorporated into a shear modified GTN model to characterise ductile fracture behaviour of an aluminium alloy (AA1050) at varying temperatures in ISF processing under different strain states. The correlation between void evolution and damage accumulation at different temperatures is revealed, and the void volume fraction (VVF) at different deformation stages is determined by conducting microscopic in-situ tensile test. By introducing a new temperature-dependent VVF function and determining appropriate GTN damage parameters, ductile fracture under different ISF processing temperatures is evaluated using FE simulation and validated by ISF experimental testing. The results show that the proposed temperature-dependent VVF function in GTN modelling is capable of predicting the ductile fracture of both the set temperatures in in-situ tensile tests and the varying temperature conditions in ISF processes. This study unveils the underlying mechanisms behind material deformation and damage evolution with consideration of temperature variations caused by tool spindle speed at various ISF forming conditions, which provides guidance for process optimisation and formability improvement in ISF process.
- 26 December 2025
- Published by Springer Nature in International Journal of Material Forming
- Vol. 19 (1) , 4
Open AccessCharacterisation and modelling of ductile fracture in incremental sheet forming of an aluminium alloy with consideration of temperature variations
Although extensive studies have been conducted to predict ductile fracture at room temperature, no attempt has been made to use Gurson–Tvergaard–Needleman (GTN) model to capture the effect of temperature due to spindle speed induced friction heat on damage accumulation in incremental sheet forming (ISF). In this work, the temperature effect is incorporated into a shear modified GTN model to characterise ductile fracture behaviour of an aluminium alloy (AA1050) at varying temperatures in ISF processing under different strain states. The correlation between void evolution and damage accumulation at different temperatures is revealed, and the void volume fraction (VVF) at different deformation stages is determined by conducting microscopic in-situ tensile test. By introducing a new temperature-dependent VVF function and determining appropriate GTN damage parameters, ductile fracture under different ISF processing temperatures is evaluated using FE simulation and validated by ISF experimental testing. The results show that the proposed temperature-dependent VVF function in GTN modelling is capable of predicting the ductile fracture of both the set temperatures in in-situ tensile tests and the varying temperature conditions in ISF processes. This study unveils the underlying mechanisms behind material deformation and damage evolution with consideration of temperature variations caused by tool spindle speed at various ISF forming conditions, which provides guidance for process optimisation and formability improvement in ISF process.
- Open Access
- 7 May 2025
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 408, 01036
Investigation of frictional behaviour in incremental sheet forming of grade one titanium sheet
Incremental Sheet Forming (ISF) is a flexible sheet forming process. Its interfacial friction between the ISF tool and the blank sheet has a significant effect to the forming forces, deformation, fracture, and surface finish. This study reports an experimental investigation into the frictional behaviour in ISF processing of Grade 1 commercial pure Titanium (Grade 1 CP Ti) using a rigid hemispheric and a roller ball tool. Straight groove tests of reciprocating sliding were conducted to measure the forming forces in both vertical and horizontal directions with and without imposing deformation under different lubrication conditions. The results showed that the friction indicator increased with the increased passes and the friction coefficients maintained a constant value. It was found that the horizontal force component due to plastic deformation were constant using different tools and under different conditions and could be quantified by comparing data from testing with and without plastic deformation.
- 7 May 2025
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 408, 01036
Open AccessInvestigation of frictional behaviour in incremental sheet forming of grade one titanium sheet
Incremental Sheet Forming (ISF) is a flexible sheet forming process. Its interfacial friction between the ISF tool and the blank sheet has a significant effect to the forming forces, deformation, fracture, and surface finish. This study reports an experimental investigation into the frictional behaviour in ISF processing of Grade 1 commercial pure Titanium (Grade 1 CP Ti) using a rigid hemispheric and a roller ball tool. Straight groove tests of reciprocating sliding were conducted to measure the forming forces in both vertical and horizontal directions with and without imposing deformation under different lubrication conditions. The results showed that the friction indicator increased with the increased passes and the friction coefficients maintained a constant value. It was found that the horizontal force component due to plastic deformation were constant using different tools and under different conditions and could be quantified by comparing data from testing with and without plastic deformation.
- Open Access
- 27 August 2024
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 401, 01014
An investigation of multi-pass incremental sheet forming
This study investigates toolpath strategies of multi-pass incremental sheet forming (MSPIF) including a combination of an IN (I) pass where the tool moves inwards and downwards and an OUT (O) pass where the tool moves outward and upward. MSPIF processes (III, IIO, IOI and IOO) were investigated to form cone and dome shapes using experimental testing and finite element (FE) simulation. It was found that any IN pass after the initial IN pass, produced stepped features due to Rigid Body Translation (RBT) of the formed part, with the magnitude of the step being dependent on the both the quantity and position of the IN passes. The IOO strategy was more effective in producing a flat bottom cup (no stepped features), but due to the succession of OUT passes used, sheet thinning occurred near the centre of the formed part. A 4-stage IOOO strategy successfully increased the final maximum draw angle by 23% relative to the maximum wall angle of a single pass. The results have shown that the MSPIF approach can be used as an effective means to improve the formability in incremental sheet forming.
- 27 August 2024
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 401, 01014
Open AccessAn investigation of multi-pass incremental sheet forming
This study investigates toolpath strategies of multi-pass incremental sheet forming (MSPIF) including a combination of an IN (I) pass where the tool moves inwards and downwards and an OUT (O) pass where the tool moves outward and upward. MSPIF processes (III, IIO, IOI and IOO) were investigated to form cone and dome shapes using experimental testing and finite element (FE) simulation. It was found that any IN pass after the initial IN pass, produced stepped features due to Rigid Body Translation (RBT) of the formed part, with the magnitude of the step being dependent on the both the quantity and position of the IN passes. The IOO strategy was more effective in producing a flat bottom cup (no stepped features), but due to the succession of OUT passes used, sheet thinning occurred near the centre of the formed part. A 4-stage IOOO strategy successfully increased the final maximum draw angle by 23% relative to the maximum wall angle of a single pass. The results have shown that the MSPIF approach can be used as an effective means to improve the formability in incremental sheet forming.
- 23 August 2023
- Published by Springer Nature
- p. 713-721
Modelling of Stress Evolution and Its Effect on Formability in Tension Under Cyclic Bending Plus Compression
- 23 August 2023
- Published by Springer Nature
- p. 713-721
Modelling of Stress Evolution and Its Effect on Formability in Tension Under Cyclic Bending Plus Compression
- 8 February 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (23) , 10680-10701
Micromechanical Modeling of the Deformation and Damage Behavior of Al6092/SiC Particle Metal Matrix Composites
- 8 February 2023
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 32 (23) , 10680-10701
Micromechanical Modeling of the Deformation and Damage Behavior of Al6092/SiC Particle Metal Matrix Composites
- Open Access
- 27 October 2022
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 42 (11-12) , 611-623
Hybrid vacuum-robotic forming of reinforced composite laminates
A methodology is presented to implement robotic actuators into diaphragm forming of composite laminates. This Hybrid Vacuum-Robotic (HyVR) process is specifically targeted to prevent ‘bridging’ type defects. Examples are presented of successfully forming laminates with deep concave features that would otherwise be impossible by diaphragm forming. The robotically controlled end effectors apply localised pressure to concave regions during the diaphragm forming process. This force application is analogous to the incremental sheet forming process. A generalised methodology is presented which can be applied to develop a bespoke HyVR process for a specific mould. It can then inform what type of end effector should be used and how to apply it within the HyVR process. A key development included in this methodology is the use of the robot to ‘pin’ the laminate to the mould, preventing any unwanted movement. This process could enable automated production of more complex components using diaphragm forming, taking advantage of its lower tooling and equipment costs.
- 27 October 2022
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 42 (11-12) , 611-623
Open AccessHybrid vacuum-robotic forming of reinforced composite laminates
A methodology is presented to implement robotic actuators into diaphragm forming of composite laminates. This Hybrid Vacuum-Robotic (HyVR) process is specifically targeted to prevent ‘bridging’ type defects. Examples are presented of successfully forming laminates with deep concave features that would otherwise be impossible by diaphragm forming. The robotically controlled end effectors apply localised pressure to concave regions during the diaphragm forming process. This force application is analogous to the incremental sheet forming process. A generalised methodology is presented which can be applied to develop a bespoke HyVR process for a specific mould. It can then inform what type of end effector should be used and how to apply it within the HyVR process. A key development included in this methodology is the use of the robot to ‘pin’ the laminate to the mould, preventing any unwanted movement. This process could enable automated production of more complex components using diaphragm forming, taking advantage of its lower tooling and equipment costs.
- 17 February 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (3-4) , 1889-1900
Numerical and experimental investigation of formability in incremental sheet forming of particle-reinforced metal matrix composite sheets
- 17 February 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (3-4) , 1889-1900
Numerical and experimental investigation of formability in incremental sheet forming of particle-reinforced metal matrix composite sheets
- 1 June 2021
- Published by Elsevier in Mechanics of Materials
- Vol. 157
A new phenomenological constitutive model for thermoplastics
- 1 June 2021
- Published by Elsevier in Mechanics of Materials
- Vol. 157
A new phenomenological constitutive model for thermoplastics
- 19 April 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 114 (9-10) , 2975-2990
Surface roughness analysis of medical grade titanium sheets formed by single point incremental forming
- 19 April 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 114 (9-10) , 2975-2990
Surface roughness analysis of medical grade titanium sheets formed by single point incremental forming