Enes Battal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Enes Battal has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ali Kemal Okyay
Department of Electrical and Electronics Engineering, Bilkent University, Ankara, 06800, Turkey
5 shared publications Taha Alper Yogurt
Bilkent University
2 shared publications- Bihter Daglar
UNAM-National Nanotechnology Research Center Bilkent University 06800 Ankara Turkey
1 shared publication - Fatih B. Atar
Bilkent University
1 shared publication Levent E. Aygun
Bilkent University
1 shared publication- Levent Erdal Aygun
Department of Electrical and Electronics Engineering, Bilkent University, Ankara 06800, Turkey
1 shared publication
Latest Publications
- 20 January 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (5) , 1340-1345
Actively tunable thin films for visible light by thermo‐optic modulation of ZnO
Applications of active control of light matter interactions within integrated photonics, hyper‐spectral imaging, reconfigurable lasers, and selective bio‐surfaces have enormously increased the demand for realization of optical modulation covering the spectrum from ultraviolet (UV) up to infrared (IR) wavelength range. In this study, we demonstrate ZnO‐based actively tunable perfect absorber operating within UV and visible spectrum with more than 5 nm shift in the resonant absorption wavelength. Using spectroscopic ellipsometry technique, we extract temperature‐dependent optical constants of atomic layer‐deposited ZnO within 0.3–1.6 and 4–40 μm spectra. We also observe bandgap narrowing of ZnO at elevated temperatures due to lattice relaxation verified by the red‐shift of phonon‐modes. At around its bandgap, refractive index variations up to 0.2 is obtained and ZnO is shown to exhibit thermo‐optic coefficient as high as 9.17 × 10−4 K−1 around the bandgap which is the largest among well‐known large bandgap materials.
- 20 January 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 213 (5) , 1340-1345
Actively tunable thin films for visible light by thermo‐optic modulation of ZnO
Applications of active control of light matter interactions within integrated photonics, hyper‐spectral imaging, reconfigurable lasers, and selective bio‐surfaces have enormously increased the demand for realization of optical modulation covering the spectrum from ultraviolet (UV) up to infrared (IR) wavelength range. In this study, we demonstrate ZnO‐based actively tunable perfect absorber operating within UV and visible spectrum with more than 5 nm shift in the resonant absorption wavelength. Using spectroscopic ellipsometry technique, we extract temperature‐dependent optical constants of atomic layer‐deposited ZnO within 0.3–1.6 and 4–40 μm spectra. We also observe bandgap narrowing of ZnO at elevated temperatures due to lattice relaxation verified by the red‐shift of phonon‐modes. At around its bandgap, refractive index variations up to 0.2 is obtained and ZnO is shown to exhibit thermo‐optic coefficient as high as 9.17 × 10−4 K−1 around the bandgap which is the largest among well‐known large bandgap materials.
- Open Access
- 28 October 2014
- Published by Wiley in Physica Status Solidi (a)
- Vol. 211 (11)
Atomic-layer-deposited zinc oxide as tunable uncooled infrared microbolometer material (Phys. Status Solidi A 11∕2014)
- 28 October 2014
- Published by Wiley in Physica Status Solidi (a)
- Vol. 211 (11)
Open AccessAtomic-layer-deposited zinc oxide as tunable uncooled infrared microbolometer material (Phys. Status Solidi A 11∕2014)
- Open Access
- 24 September 2013
- Published by Optica Publishing Group in Optics Express
- Vol. 21 (20) , 23324
Plasmonically enhanced hot electron based photovoltaic device: erratum
This erratum amends the missing acknowledgment section in our manuscript.
- 24 September 2013
- Published by Optica Publishing Group in Optics Express
- Vol. 21 (20) , 23324
Open AccessPlasmonically enhanced hot electron based photovoltaic device: erratum
This erratum amends the missing acknowledgment section in our manuscript.
- 15 August 2012
- Published by Springer Nature in Plasmonics
- Vol. 8 (2) , 509-513
Ultrahigh Contrast One-Way Optical Transmission Through a Subwavelength Slit
- 15 August 2012
- Published by Springer Nature in Plasmonics
- Vol. 8 (2) , 509-513
Ultrahigh Contrast One-Way Optical Transmission Through a Subwavelength Slit
- 10 April 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (9) , 9458-9464
Triangular metallic gratings for large absorption enhancement in thin film Si solar cells
We estimate high optical absorption in silicon thin film photovoltaic devices using triangular corrugations on the back metallic contact. We computationally show 21.9% overall absorptivity in a 100-nm-thick silicon layer, exceeding any reported absorptivity using single layer gratings placed on the top or the bottom, considering both transverse electric and transverse magnetic polarizations and a wide spectral range (280 – 1100 nm). We also show that the overall absorptivity of the proposed scheme is relatively insensitive to light polarization and the angle of incidence. We also discuss the implications of potential fabrication process variations on such a device.
- 10 April 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (9) , 9458-9464
Triangular metallic gratings for large absorption enhancement in thin film Si solar cells
We estimate high optical absorption in silicon thin film photovoltaic devices using triangular corrugations on the back metallic contact. We computationally show 21.9% overall absorptivity in a 100-nm-thick silicon layer, exceeding any reported absorptivity using single layer gratings placed on the top or the bottom, considering both transverse electric and transverse magnetic polarizations and a wide spectral range (280 – 1100 nm). We also show that the overall absorptivity of the proposed scheme is relatively insensitive to light polarization and the angle of incidence. We also discuss the implications of potential fabrication process variations on such a device.