Hisanori Ando
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Hisanori Ando has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
Mutsuo Tanaka
Biomedical Research Institute, AIST, Tsukuba, Japan
18 shared publicationsYoshie Souma
Osaka National Research Institute, AIST, Midorigaoka, Ikeda, Osaka 563-8577, Japan
17 shared publications- Masahiro Fujiwara
National Institute of Advanced Industrial Science and Technology (RICPT; Tohoku Center), 4-2-1 Nigatake, Miyagino-ku, Sendai, Miyagi 983-8551, Japan
15 shared publications - Masaru Yao
Research Institute of Electrochemical Energy, Department of Energy and Environment, National Institute of Advanced Industrial Science and Technology (AIST), 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577, Japan
12 shared publications - Tetsu Kiyobayashi
Research Institute of Electrochemical Energy, Department of Energy and Environment, National Institute of Advanced Industrial Science and Technology (AIST), 1-8-31 Midorigaoka, Ikeda, Osaka 563-8577, Japan
10 shared publications - Qiang Xu
Southern University of Science and Technology
9 shared publications
Latest Publications
- Open Access
- 19 August 2025
- Published by Wiley in Batteries & Supercaps
- Vol. 9 (1)
A Long Cycle‐Life and Recyclable Anthraquinone Oligomer Connected via Amide Bonds for Use in Rechargeable Organic Batteries
With the increasing demand for energy, the requirements for energy storage systems have also increased. For example, rechargeable lithium batteries, which are the primary power sources for mobile devices, must have a high energy density and be environmentally friendly. Herein, organic compounds linked by amide bonds that underwent chemical hydrolysis or biodegradation as sustainable battery materials are investigated. In particular, an amide‐bonded anthraquinone oligomer is synthesized, and its potential as a cathode‐active material is examined. The anthraquinone monomer, with a theoretical capacity of 258 mAh g −1 , exhibits rapid capacity decay during the cycle test; however, the synthesized oligomer, with a theoretical capacity of 144 mAh g −1 , exhibits excellent cycle‐life performance. For example, it retains ≈82% of its initial capacity after 200 cycles. This electrochemical improvement is attributed to the decreased solubility in the electrolyte solution due to oligomerization. This study contributes to the development of long cycle‐life organic batteries with environmental benefits.
- 19 August 2025
- Published by Wiley in Batteries & Supercaps
- Vol. 9 (1)
Open AccessA Long Cycle‐Life and Recyclable Anthraquinone Oligomer Connected via Amide Bonds for Use in Rechargeable Organic Batteries
With the increasing demand for energy, the requirements for energy storage systems have also increased. For example, rechargeable lithium batteries, which are the primary power sources for mobile devices, must have a high energy density and be environmentally friendly. Herein, organic compounds linked by amide bonds that underwent chemical hydrolysis or biodegradation as sustainable battery materials are investigated. In particular, an amide‐bonded anthraquinone oligomer is synthesized, and its potential as a cathode‐active material is examined. The anthraquinone monomer, with a theoretical capacity of 258 mAh g −1 , exhibits rapid capacity decay during the cycle test; however, the synthesized oligomer, with a theoretical capacity of 144 mAh g −1 , exhibits excellent cycle‐life performance. For example, it retains ≈82% of its initial capacity after 200 cycles. This electrochemical improvement is attributed to the decreased solubility in the electrolyte solution due to oligomerization. This study contributes to the development of long cycle‐life organic batteries with environmental benefits.
- Open Access
Recycling Compatible Organic Electrode Materials Containing Amide Bonds for Use in Rechargeable Batteries
Organic rechargeable batteries that do not use any scarce heavy metals are candidates for the next generation of rechargeable batteries; although, it is not easy to realize both high capacity and long cycle life. Organic compounds linked by amide bonds are expected to have superior recycling properties after battery degradation, since they will become a single monomer upon hydrolysis. In this study, anthraquinone was chosen as a model redox active unit, and dimeric and trimeric compounds were synthesized, their cycle performances as electrode materials for use in rechargeable batteries were compared, and a trend in which oligomerization improves cycle properties was confirmed. Furthermore, quantum chemistry calculations suggest that oligomerization decreases solubility, which would support a longer life for oligomerized compounds. This methodology will lead to the development of organic rechargeable batteries with further environmental benefits.
Open AccessRecycling Compatible Organic Electrode Materials Containing Amide Bonds for Use in Rechargeable Batteries
Organic rechargeable batteries that do not use any scarce heavy metals are candidates for the next generation of rechargeable batteries; although, it is not easy to realize both high capacity and long cycle life. Organic compounds linked by amide bonds are expected to have superior recycling properties after battery degradation, since they will become a single monomer upon hydrolysis. In this study, anthraquinone was chosen as a model redox active unit, and dimeric and trimeric compounds were synthesized, their cycle performances as electrode materials for use in rechargeable batteries were compared, and a trend in which oligomerization improves cycle properties was confirmed. Furthermore, quantum chemistry calculations suggest that oligomerization decreases solubility, which would support a longer life for oligomerized compounds. This methodology will lead to the development of organic rechargeable batteries with further environmental benefits.
- 22 May 2023
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 127 (21) , 10038-10044
Capacity Decay Mechanism of Lithium–Sulfur Batteries Using a Microporous Activated Carbon–Sulfur Composite as the Cathode Material
- 22 May 2023
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry C
- Vol. 127 (21) , 10038-10044
Capacity Decay Mechanism of Lithium–Sulfur Batteries Using a Microporous Activated Carbon–Sulfur Composite as the Cathode Material
- Open Access
- 9 October 2020
- Published by Springer Nature in Scientific Reports
- Vol. 10 (1) , 1-8
Local structure and electrochemical performances of sulfurized polyethylene glycol after heat treatment
Designing a high-capacity positive electrode material is critical for the advancement of lithium-ion batteries. Sulfurized polyethylene glycol (SPEG), containing ca. 61 wt% of sulfur, is a promising positive electrode material that exhibits a large initial discharge capacity of more than 800 mAh g−1. In this study, we present the local structure and electrochemical performances of SPEG. A high-energy X-ray total scattering experiment revealed that sulfur in SPEG is predominantly fragmented and bound to carbon atoms. The changes in the physicochemical properties of SPEG due to heat treatment with nitrogen gas at various temperatures were investigated using thermogravimetric analysis, Raman spectroscopy, X-ray absorption near edge structure, and extended X-ray absorption fine structure. Comparing the electrochemical performances of SPEG after heat treatment at various temperatures, it was found that S–S and C=S bonds contribute to the overall electrochemical performance of SPEG.
- 9 October 2020
- Published by Springer Nature in Scientific Reports
- Vol. 10 (1) , 1-8
Open AccessLocal structure and electrochemical performances of sulfurized polyethylene glycol after heat treatment
Designing a high-capacity positive electrode material is critical for the advancement of lithium-ion batteries. Sulfurized polyethylene glycol (SPEG), containing ca. 61 wt% of sulfur, is a promising positive electrode material that exhibits a large initial discharge capacity of more than 800 mAh g−1. In this study, we present the local structure and electrochemical performances of SPEG. A high-energy X-ray total scattering experiment revealed that sulfur in SPEG is predominantly fragmented and bound to carbon atoms. The changes in the physicochemical properties of SPEG due to heat treatment with nitrogen gas at various temperatures were investigated using thermogravimetric analysis, Raman spectroscopy, X-ray absorption near edge structure, and extended X-ray absorption fine structure. Comparing the electrochemical performances of SPEG after heat treatment at various temperatures, it was found that S–S and C=S bonds contribute to the overall electrochemical performance of SPEG.
- Open Access
- 2 October 2020
- Published by Springer Nature in Communications Materials
- Vol. 1 (1) , 1-10
Improved gravimetric energy density and cycle life in organic lithium-ion batteries with naphthazarin-based electrode materials
Replacing the scarce metal-based positive electrode materials currently used in rechargeable lithium ion batteries with organic compounds helps address environmental issues and might enhance gravimetric electrochemical capacity. The challenge has been to find organic materials with both high capacity and long-cycle life. Here, we study the naphthazarin (5,8-dihydroxy-1,4-naphthoquinone) skeleton as a high capacity candidate electrode for lithium-ion batteries, showing a multielectron-transfer type redox reaction. We also use electron energy-loss spectroscopy to reveal the reaction stoichiometry during charge/discharge processes. While the lithium salt of naphthazarin itself helped deliver a high initial capacity, its cycle-life was not satisfactory. Instead, a newly synthesized naphthazarin-dimer shows a lengthened cycle-life without sacrificing the initial high capacity of 416 mAh g−1and energy density of 1.1 Wh g−1.
- 2 October 2020
- Published by Springer Nature in Communications Materials
- Vol. 1 (1) , 1-10
Open AccessImproved gravimetric energy density and cycle life in organic lithium-ion batteries with naphthazarin-based electrode materials
Replacing the scarce metal-based positive electrode materials currently used in rechargeable lithium ion batteries with organic compounds helps address environmental issues and might enhance gravimetric electrochemical capacity. The challenge has been to find organic materials with both high capacity and long-cycle life. Here, we study the naphthazarin (5,8-dihydroxy-1,4-naphthoquinone) skeleton as a high capacity candidate electrode for lithium-ion batteries, showing a multielectron-transfer type redox reaction. We also use electron energy-loss spectroscopy to reveal the reaction stoichiometry during charge/discharge processes. While the lithium salt of naphthazarin itself helped deliver a high initial capacity, its cycle-life was not satisfactory. Instead, a newly synthesized naphthazarin-dimer shows a lengthened cycle-life without sacrificing the initial high capacity of 416 mAh g−1and energy density of 1.1 Wh g−1.
- 1 March 2019
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 225, 105-110
Mixture of monoglyme-based solvent and lithium Bis(trifluoromethanesulfonyl)amide as electrolyte for lithium ion battery using silicon electrode
- 1 March 2019
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 225, 105-110
Mixture of monoglyme-based solvent and lithium Bis(trifluoromethanesulfonyl)amide as electrolyte for lithium ion battery using silicon electrode
- 18 February 2019
- Published by Wiley in Chemphyschem
- Vol. 20 (7) , 967-971
Anthraquinone‐Based Oligomer as a Long Cycle‐Life Organic Electrode Material for Use in Rechargeable Batteries
An anthraquinone (AQ)‐based dimer and trimer linked by a triple bond (−C≡C−) were newly synthesized as active materials for the positive electrode of rechargeable lithium batteries. These synthesized oligomers exhibited an initial discharge capacity of about 200 mAh g−1 with an average voltage of 2.2–2.3 V versus Li(C.E.). These capacity values are similar to that of the AQ‐monomer, reflecting the two‐electron transfer redox per AQ unit. Regarding their cycling stability, the capacity of the monomer electrode quickly decreased; however, the electrodes of the prepared oligomers showed an improved cycling performance. In particular, the discharge capacities of the trimer remained almost constant for 100 cycles. A theoretical calculation revealed that the intermolecular binding energy can be increased to the level of a weak covalent bonding by oligomerization, which would be beneficial to suppress the dissolution of the organic active materials into the electrolyte solutions. These results show that the cycle‐life of organic active materials can be extended without lowering the discharge capacity by the oligomerization of the redox active molecule unit.
- 18 February 2019
- Published by Wiley in Chemphyschem
- Vol. 20 (7) , 967-971
Anthraquinone‐Based Oligomer as a Long Cycle‐Life Organic Electrode Material for Use in Rechargeable Batteries
An anthraquinone (AQ)‐based dimer and trimer linked by a triple bond (−C≡C−) were newly synthesized as active materials for the positive electrode of rechargeable lithium batteries. These synthesized oligomers exhibited an initial discharge capacity of about 200 mAh g−1 with an average voltage of 2.2–2.3 V versus Li(C.E.). These capacity values are similar to that of the AQ‐monomer, reflecting the two‐electron transfer redox per AQ unit. Regarding their cycling stability, the capacity of the monomer electrode quickly decreased; however, the electrodes of the prepared oligomers showed an improved cycling performance. In particular, the discharge capacities of the trimer remained almost constant for 100 cycles. A theoretical calculation revealed that the intermolecular binding energy can be increased to the level of a weak covalent bonding by oligomerization, which would be beneficial to suppress the dissolution of the organic active materials into the electrolyte solutions. These results show that the cycle‐life of organic active materials can be extended without lowering the discharge capacity by the oligomerization of the redox active molecule unit.
- 11 July 2017
- Published by Springer Nature in Journal of Materials Science
- Vol. 52 (20) , 12401-12408
Rechargeable organic batteries using chloro-substituted naphthazarin derivatives as positive electrode materials
- 11 July 2017
- Published by Springer Nature in Journal of Materials Science
- Vol. 52 (20) , 12401-12408
Rechargeable organic batteries using chloro-substituted naphthazarin derivatives as positive electrode materials
- 1 September 2016
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2016-02 (3) , 303
Improvement in the Thermal Safety of Rechargeable Lithium Batteries: Endothermic Behavior of Organic Positive-Electrode Materials
The current rechargeable lithium batteries have potential risks related to the thermal safety. These batteries sometimes suffers from an unexpected rapid temperature increase. This phenomenon, called thermal runaway, is triggered by some abuse conditions such as overcharge and internal short-circuits, which could lead to explosions or fire. Considering large scale battery applications including electric vehicles and stationary system, extreme caution for this safety control is particularly important. To ensure the battery safety, many approaches have been suggested. The use of a particular kind of separator, the combination with a solid electrolyte, and coating of electrode materials are common strategies. The introduction of an external battery management system is also applied. Furthermore, it is inevitable to find out a thermally safe electrode material. We have studied a series of organic active materials to reduce the amount of minor metal-based materials in the positive electrodes from the view point of the resource concern and have demonstrated that some low-molecular-weight quinone compounds show relatively large capacities based on their multi-electron transfer-type redox reaction [1‒3]. There are many other reports describing the charge/discharge performance of such organic active materials; however, the thermal behavior of these organic ones has been rarely discussed. Here, we compares the thermal behavior of a conventional lithium cobalt oxide (LiCoO2) and an organic active material using an example of 2,5-dimethoxy-1,4-benzoquinone (DMBQ) (Fig. 1a). This organic active material shows a large initial capacity of more than 300 mAh/g and relatively good cycle-life stability. Figure 1b shows the differential scanning calorimetry profiles of the charged (delithiated) LiCoO2-electrode and the DMBQ-electrode under the coexistence with an electrolyte solution. The LiCoO2-electrode showed a sharp exothermic peak at around 240oC. Similar exothermic behaviors are often observed for a lot of minor-metal oxides, which leads to the thermal runaway. As for the mechanism, it is commonly understood that charged minor-metal oxides often release oxygen at elevated temperatures, which then induces the combustion reaction of electrolyte solutions. On the other hand, the DMBQ-electrode showed an opposite behavior: some endothermic peaks were observed during the measurement. In general, many organic compounds have a melting point or decomposition point, and these reactions are endothermic. The endothermic behavior observed for the DMBQ-electrode in this study is also considered to reflect such melting and/or thermal decomposition of the DMBQ particles in the electrode. Since many organic materials do not contain any minor metals, the use of these materials can alleviate resource constraint issues. Furthermore, their endothermic behavior can be a promising characteristic, which would contribute to the development of a thermally safe battery system. References: [1] M. Yao, et al., J. Power Sources, 195, 8336 (2010). [2] M. Yao, et al., Mat. Sci. Eng. B, 177, 483 (2012). [3] M. Yao, et al., Energy Procedia, 56, 228 (2014). Figure 1
- 1 September 2016
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2016-02 (3) , 303
Improvement in the Thermal Safety of Rechargeable Lithium Batteries: Endothermic Behavior of Organic Positive-Electrode Materials
The current rechargeable lithium batteries have potential risks related to the thermal safety. These batteries sometimes suffers from an unexpected rapid temperature increase. This phenomenon, called thermal runaway, is triggered by some abuse conditions such as overcharge and internal short-circuits, which could lead to explosions or fire. Considering large scale battery applications including electric vehicles and stationary system, extreme caution for this safety control is particularly important. To ensure the battery safety, many approaches have been suggested. The use of a particular kind of separator, the combination with a solid electrolyte, and coating of electrode materials are common strategies. The introduction of an external battery management system is also applied. Furthermore, it is inevitable to find out a thermally safe electrode material. We have studied a series of organic active materials to reduce the amount of minor metal-based materials in the positive electrodes from the view point of the resource concern and have demonstrated that some low-molecular-weight quinone compounds show relatively large capacities based on their multi-electron transfer-type redox reaction [1‒3]. There are many other reports describing the charge/discharge performance of such organic active materials; however, the thermal behavior of these organic ones has been rarely discussed. Here, we compares the thermal behavior of a conventional lithium cobalt oxide (LiCoO2) and an organic active material using an example of 2,5-dimethoxy-1,4-benzoquinone (DMBQ) (Fig. 1a). This organic active material shows a large initial capacity of more than 300 mAh/g and relatively good cycle-life stability. Figure 1b shows the differential scanning calorimetry profiles of the charged (delithiated) LiCoO2-electrode and the DMBQ-electrode under the coexistence with an electrolyte solution. The LiCoO2-electrode showed a sharp exothermic peak at around 240oC. Similar exothermic behaviors are often observed for a lot of minor-metal oxides, which leads to the thermal runaway. As for the mechanism, it is commonly understood that charged minor-metal oxides often release oxygen at elevated temperatures, which then induces the combustion reaction of electrolyte solutions. On the other hand, the DMBQ-electrode showed an opposite behavior: some endothermic peaks were observed during the measurement. In general, many organic compounds have a melting point or decomposition point, and these reactions are endothermic. The endothermic behavior observed for the DMBQ-electrode in this study is also considered to reflect such melting and/or thermal decomposition of the DMBQ particles in the electrode. Since many organic materials do not contain any minor metals, the use of these materials can alleviate resource constraint issues. Furthermore, their endothermic behavior can be a promising characteristic, which would contribute to the development of a thermally safe battery system. References: [1] M. Yao, et al., J. Power Sources, 195, 8336 (2010). [2] M. Yao, et al., Mat. Sci. Eng. B, 177, 483 (2012). [3] M. Yao, et al., Energy Procedia, 56, 228 (2014). Figure 1
- Open Access
- 1 June 2016
- Published by Elsevier in Energy Procedia
- Vol. 89, 222-230
Polycyclic Quinone Fused by a Sulfur-containing Ring as an Organic Positive-electrode Material for Use in Rechargeable Lithium Batteries
- 1 June 2016
- Published by Elsevier in Energy Procedia
- Vol. 89, 222-230
Open AccessPolycyclic Quinone Fused by a Sulfur-containing Ring as an Organic Positive-electrode Material for Use in Rechargeable Lithium Batteries