YSYuh Shiohara

Yuh Shiohara

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yuh Shiohara has a total of 168 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Enhancement of $J_{\mathrm{c}}$ Properties in Magnetic Fields of BaZrO3Doped REBa2Cu3O6+δCoated Conductors by a Newly Modified TFA-MOD Process

    by K. Nakaoka, K. Kimura, T. Kato, R. Yoshida, Y. Usui, M. Nakamura, T. Izumi, Y. Shiohara

    A modified heat-treatment procedure, which consisted of three steps, i.e., 1) calcination, 2) intermediate heat-treatment (IHT), and 3) crystallization, was developed for the metal organic deposition method using trifluoroacetates (TFA). BaZrO 3 -doped Y 0.77 Gd 0.23 Ba 2 Cu 3 O 6+δ (YGdBCO) coated conductors fabricated by this modified procedure provided the minimum critical current density (J c ) value of 0.21 MA/cm 2 at 77 K in 3 T, which was as high as 2.1 times the value obtained by the conventional one, and a homogeneous dispersion of BaZrO 3 nanoparticles with finer size in the matrix. Furthermore, the 1-D theoretical analysis of the reaction kinetics in the IHT process, considering diffusion and growth kinetics at the interface between the precursor layer and the calcined layer, was proposed, and the estimated reaction rate was compared with experimental ones.


  • Three-dimensional characterization of BaHfO3precipitates in GdBa2Cu3O7-yflim using STEM tomography

    by T. Nishiyama, K. Kaneko, K. Yamada, R. Teranishi, T. Kato, T. Hirayama, H. Tobita, T. Izumi, Y. Shiohara

    Introduction Since the discovery of REBa2Cu3O7-y (RE: Rare Earth element, REBCO) superconductors, they have been expected as the best candidates for the power cable application due to its high critical temperature (Tc) and critical current density (Jc). Among those REBCO superconductors, GdBa2Cu3O7-y (GdBCO) have been receiving great interest because they have higher Tc and Jc than YBa2Cu3O7-y [1]. GdBCO with various types of precipitates as artificial pinning centers (APCs) have been proposed to minimize the anisotropy of Jc characteristics under the magnetic field. Among those precipitates, BaHfO3 (BHO) was found most effective precipitates as APCs in GdBCO film prepared by pulsed laser deposition (PLD) method [2]. It is therefore necessary to investigate not only the morphologies but also the dispersion of BHO precipitates within the GdBCO, to understand the role of BHO for the superconducting characteristics. In this study, morphologies and dispersions of BHO precipitates were characterized three-dimensional by scanning transmission electron tomography Experimental BHO dispersed GdBCO films were fabricated on Hastelloy C-276TM substrates with buffer layers of CeO2/LaMnO3/MgO/ Gd2ZrO7 by PLD method. To observe microstructure of GdBCO film with BHO precipitates, cross-section TEM specimens were prepared by FIB method using Quanta 3D-200 (FEI, USA) with acceleration voltage from 2 to 30 kV. Three-dimensional information such as morphology and dispersion, of BHO precipitates were characterized by electron tomography using STEM-HAADF. Result and discussion

  • Progress in R&D of coated conductor in M-PACC project

    by T. Izumi, A. Ibi, K. Nakaoka, T. Taneda, T. Yoshida, Y. Takagi, T. Nakamura, T. Machi, K. Katayama, N. Sakai, et al.


  • Development of REBCO Coated Conductors by TFA-MOD Method With High Characteristic in Magnetic Field

    by K. Kimura, R. Hironaga, Y. Takahashi, T. Nakanishi, T. Koizumi, T. Hasegawa, K. Higashikawa, M. Inoue, T. Kiss, T. Kato, et al.

    YxGd(1 - x)Ba2Cu3 Oy coated conductors (CCs) with artificial pinning centers (APCs) were fabricated by the trifluoroacetates-metal organic deposition method using a batch heat-treatment process. This process has been industrially applied to fabricate long superconducting tapes that have high critical current (Ic). From the viewpoint of applications, the characteristics in magnetic fields become further important, and one solution has been shown previously as introduction of APCs such as BaZrO3. We applied the technique to our CCs fabrication process. The heat-treatment conditions, specifically total gas pressure, oxygen concentration, and crystallization temperature, were optimized for the batch heat-treatment process. As a consequence, fabricated CC showed extremely high characteristic Jc value of 3.5 MA/cm2 in self field, and 0.3 MA/cm2 at 3 T in liquid N2. Moreover, by cross-sectional transmission electron microscopy observation, it was confirmed that the APC was distributed uniformly. Furthermore, the anisotropy of the pinning center is also examined based on the evaluation result of the angular dependence of Jc in 3T.


  • Effect of Solution Composition on Superconducting Properties of YBCO Derived From TFA-MOD Process

    by K. Nakaoka, M. Yoshizumi, Y. Usui, T. Izumi, Y. Shiohara

    The crystallization process of trifluoroacetate-metal-organic deposition derived YBa 2 Cu 3 O 7-y (YBCO) crystals has been investigated to understand the influence of the starting solution composition on the crystal growth process. The starting solutions with molar ratios of Y: Ba: Cu = 1.0: 2.0: 3.0 (stoichiometry) and 1.0:1.5:3.0 (Ba-deficient) were examined. The highest I c values were achieved at 100 min holding time of the conversion step for 0.8- μm-thick YBCO films, which were independent of the starting solutions. The degradation of I c performance was observed only in the films prepared from the stoichiometric solution with longer holding time than 100 min. The longer holding times for disappearing of the X-ray diffraction peak of BaF 2 derived from the stoichiometric solution is required compared to that from the Ba-deficient solution. On the other hand, the epitaxial growth rate measured from cross-sectional scanning electron microscopic observation for the YBCO films showed no difference between each other. X-ray diffraction analysis on the YBCO films fabricated from stoichiometric starting solution suggested that BaCuO 2 and/or Y 2 O 3 phases formed during the solid-state reaction process. The degradation of I c performance might be caused by the formation of BaCuO 2 phases.


  • Development of REBCO Superconducting Transformers With a Current Limiting Function

    by M. Iwakuma, Y. Katanosaka, S. Sato, H. Hayashi, H. Okamoto, Y. Gosho, A. Tomioka, M. Konno, Y. Iijima, T. Saitoh, et al.

    We designed and fabricated a 10 kVA single-phase transformer with RE 1 Ba 2 Cu 3 O 7-δ (REBCO, RE:Rare Earth, Y, Gd, etc.) superconducting tapes. It had a 4-winding structure at the beginning. In this study, we removed the auxiliary windings and made a test as a general 2-winding transformer. Making repeated short circuit tests, we further investigated the response of the REBCO superconducting windings against a fault excess current. Although the short circuit current decayed satisfactorily, the whole of the REBCO superconducting windings did not shift to normal state even if the short circuit current exceeded the critical current all over the length of REBCO tapes. The induced normal resistance depended on the primary voltage. To study the phenomena, we derived the basic equations and made numerical simulations taking into account of flux-flow state, in which the equivalent resistance and generated heat are much smaller than those in normal state, and also the dependences of the critical current on temperature, applied magnetic field and the applied field angle to the tape face. It was clarified that short circuit current was limited not only by normal resistance but also by flux-flow one. The introduction of the concept of flux-flow state made it possible to quantitatively explain the behavior of the REBCO superconducting transformer at a sudden short circuit.


  • Consideration of sub-cooled LN2 circulation system for HTS power machines

    by Shigeru Yoshida, Hirokazu Hirai, N. Nara, T. Nagasaka, M. Hirokawa, H. Okamoto, H. Hayashi, Y. Shiohara

    We consider a sub-cooled liquid nitrogen (LN) circulation system for HTS power equipment. The planned circulation system consists of a sub-cool heat exchanger (subcooler) and a circulation pump. The sub-cooler will be connected to a neon turbo- Brayton cycle refrigerator with a cooling power of 2 kW at 65 K. Sub-cooled LN will be delivered into the sub-cooler by the pump and cooled within it. Sub-cooled LN is adequate fluid for cooling HTS power equipment, because its dielectric strength is high and it supports a large critical current. However, a possibility of LN solidification in the sub-cooler is a considerable issue. The refrigerator will produce cold neon gas of about 60 K, which is lower than the nitrogen freezing temperature of 63 K. Therefore, we designed two-stage heat exchangers which are based on a plate-fin type and a tube-intube type. Process simulations of those heat exchangers indicate that sub-cooled LN is not frozen in either sub-cooler. The plate-fin type sub-cooler is consequently adopted for its reliability and compactness. Furthermore, we found that a cooling system with a Brayton refrigerator has the same total cooling efficiency as a cooling system with a Stirling refrigerator.


  • Feasibility Study on a 400 kW–3600 rpm REBCO Fully Superconducting Motor

    by Masataka Iwakuma, Toshiyuki Ogata, Shinichiro Tomoda, Takanobu Kisu, Yutaka Yoshida, Atsushi Ishiyama, Yutaka Yamada, Teruo Izumi, Yuh Shiohara

    We conceptually designed a 400 kW-3600 rpm synchronous motor with RE (RE: Rare earth, Y, Gd and so on, REBCO) superconducting tapes and studied the feasibility of fully superconducting ones. First the ac loss properties and the dependences of the critical current, , on temperature, , magnetic field, , and applied magnetic field angle, , of the REBCO tapes at 30 K to 77 K were measured. Next, 400 kW-3600 rpm fully superconducting motors were designed by taking into account of and then their properties, e.g. ac losses, efficiency, torque ripple and so on, were numerically calculated. According to the conventional theories, the induced ac losses in the armature windings exceeded several kW and the efficiency decreased rather than conventional normal motors. On the contrary, by taking account of the tremendous low-ac-loss properties of REBCO superconductors which were recently discovered as magnetic phase transition, the ac losses were reduced to around one hundredth. In consequence a feasible prospect of advantageous REBCO fully superconducting motors was obtained.


  • Strain Dependence of Superconducting Properties for GdBCO Coated Conductor in High Field Under Tensile Load

    by H. Oguro, T. Suzuki, K. Minegishi, S. Awaji, K. Watanabe, G. Nishijima, M. Sugano, S. Machiya, T. Shobu, M. Sato, et al.

    The strain dependence of Tc and Ic for the GdBCO coated conductor was measured at 77 and 4.2 K in magnetic fields. Tc decreased with increasing applied tensile strain. For the Ic measurements, the magnetic field was applied in the direction parallel to the c-axis (perpendicular to the tape surface). Ic in fields was degraded with increasing strain, and the strain dependence of Ic increased with increasing magnetic field. The ratio of the Ic degradation at 4.2 K was smaller than that at 77 K. These results mean that the Tc degradation is one of the reasons for Ic degradation at 77 K at least. Further, in order to understand the strain effect at 4.2 K, the internal strain of the GdBCO coated conductor under tensile strain was measured using synchrotron radiation. It was found that the strain behavior for the a-axis is different from that for the b-axis. This result suggests that the strain dependence of Ic for GdBCO coated conductors under external tensile strain is related with the Tc degradation behavior of the crystal.


  • Field Angle Dependence of Critical Current Density in YGdBCO Coated Conductor

    by M. Kiuchi, T. Koida, J. Minami, Y. Takahashi, E. S. Otabe, T. Matsushita, M. Miura, T. Izumi, Y. Shiohara, T. Kato

    The improvement of critical current density properties of REBCO coated conductors for applications in superconducting power devices is desired. It is known that the critical current density J c of REBCO thin films made by the TFA-MOD method in a magnetic field is greatly improved by the introduction of BZO-nanoparticles of a non-superconducting phase as artificial pinning centers. In addition, the field angle anisotropy can also be reduced by isotropic flux pinning interactions of nanoparticles. However, a detailed report on the mechanism of flux pinning with a quantitative investigation in such coated conductors has not been given. In this study, the field angle dependence of the critical current density is measured for TFA-MOD-processed YGdBCO coated conductor with a superconducting layer of 0.65 μm thick, and the results are theoretically analysed to clarify the flux pinning mechanism.