Hiroaki Kumakura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hiroaki Kumakura has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
Kazumasa Togano
National Institute for Materials Science
10 shared publications- Akiyoshi Matsumoto
National Institute for Materials Science
9 shared publications Hitoshi Kitaguchi
National Institute for Materials Science
6 shared publicationsZhaoshun Gao
National Institute for Materials Science
3 shared publicationsAkiyoshi Matsumoto
National Institute for Materials Science
2 shared publicationsEi Nakamura
2 shared publications
Latest Publications
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-7
Resent Progress on MgB2 Wires
Densification of MgB$_{\text{2}}$ core in an in situ PIT MgB$_{\text{2}}$ wire is one of the key factors to increase Jc values. Hot pressing, cold pressing before a heat treatment and hot isostatic pressing (HIP) are effective in densifying the core and thus, increasing Jc values. Mechanical alloying or mechanical milling of Mg+B precursor powder by a high-energy ball milling is also effective in increasing the core density and Jc values. Upper critical field Hc2 is another important parameter. Carbon doping to MgB$_{\text{2}}$ not only increases Hc2 but also decreases the anisotropy in Hc2, both of which are effective in enhancing Jc of MgB$_{\text{2}}$ wires in magnetic fields. The doping of some kinds of hydrocarbon or carbohydrate to a Mg+B precursor powder and the use of carbon-coated B powder as a starting material is effective for in situ PIT MgB$_{\text{2}}$ wires. Internal Mg diffusion (IMD) method much increases the MgB$_{\text{2}}$ filling density and Jc higher than 105 A/cm2 is obtained at 20 K and 4 T by using carbon-doped B powder. Solenoid coils were fabricated with IMD wires and coil tests were carried out. Concerning to AC loss of MgB$_{\text{2}}$ wires, cabling of small diameter mono-core MgB$_{\text{2}}$ wires is one of the effective methods to reduce both hysteresis loss and coupling loss. Superconducting joints of unreacted C-doped multi-filamentary wire showed joint resistance of 10−14 Ω at 20 K. But joint Ic was only 1/4 of wire Ic. A joint of reacted mono-core wire was reported to have resistance of 10−14 Ω at 20 K, 1 T. Excellent joint Ic of 78% of wire Ic were obtained.
- 16 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-7
Resent Progress on MgB2 Wires
Densification of MgB$_{\text{2}}$ core in an in situ PIT MgB$_{\text{2}}$ wire is one of the key factors to increase Jc values. Hot pressing, cold pressing before a heat treatment and hot isostatic pressing (HIP) are effective in densifying the core and thus, increasing Jc values. Mechanical alloying or mechanical milling of Mg+B precursor powder by a high-energy ball milling is also effective in increasing the core density and Jc values. Upper critical field Hc2 is another important parameter. Carbon doping to MgB$_{\text{2}}$ not only increases Hc2 but also decreases the anisotropy in Hc2, both of which are effective in enhancing Jc of MgB$_{\text{2}}$ wires in magnetic fields. The doping of some kinds of hydrocarbon or carbohydrate to a Mg+B precursor powder and the use of carbon-coated B powder as a starting material is effective for in situ PIT MgB$_{\text{2}}$ wires. Internal Mg diffusion (IMD) method much increases the MgB$_{\text{2}}$ filling density and Jc higher than 105 A/cm2 is obtained at 20 K and 4 T by using carbon-doped B powder. Solenoid coils were fabricated with IMD wires and coil tests were carried out. Concerning to AC loss of MgB$_{\text{2}}$ wires, cabling of small diameter mono-core MgB$_{\text{2}}$ wires is one of the effective methods to reduce both hysteresis loss and coupling loss. Superconducting joints of unreacted C-doped multi-filamentary wire showed joint resistance of 10−14 Ω at 20 K. But joint Ic was only 1/4 of wire Ic. A joint of reacted mono-core wire was reported to have resistance of 10−14 Ω at 20 K, 1 T. Excellent joint Ic of 78% of wire Ic were obtained.
- Open Access
Sloshing Measurements inside a Liquid Hydrogen Tank with External-Heating-Type MgB2 Level Sensors during Marine Transportation by the Training Ship Fukae-Maru
Recently, a project was initiated in Japan to transport a large amount of liquid hydrogen (LH2) from Australia to Japan by sea. It is important to understand the sloshing and boil-off that are likely to occur inside an LH2 tank during marine transportation by ship, but such characteristics are yet to be experimentally clarified. To do so, we combined the liquid level detected by five 500 mm long external-heating-type magnesium diboride (MgB2) level sensors with synchronous measurements of temperature, pressure, ship motion, and acceleration during a zigzag maneuver. During this zigzag maneuver, the pressure of gaseous hydrogen (GH2) in the small LH2 tank increased to roughly 0.67 MPaG/h, and the temperature of the GH2 in the small LH2 tank increased at the position of gaseous hydrogen at roughly 1.0 K/min when the maximum rolling angle was 5°; the average rolling and liquid-oscillation periods were 114 and 118 s, respectively, as detected by the MgB2 level sensors, which therefore detected a long-period LH2 wave due to the ship’s motion.
Open AccessSloshing Measurements inside a Liquid Hydrogen Tank with External-Heating-Type MgB2 Level Sensors during Marine Transportation by the Training Ship Fukae-Maru
Recently, a project was initiated in Japan to transport a large amount of liquid hydrogen (LH2) from Australia to Japan by sea. It is important to understand the sloshing and boil-off that are likely to occur inside an LH2 tank during marine transportation by ship, but such characteristics are yet to be experimentally clarified. To do so, we combined the liquid level detected by five 500 mm long external-heating-type magnesium diboride (MgB2) level sensors with synchronous measurements of temperature, pressure, ship motion, and acceleration during a zigzag maneuver. During this zigzag maneuver, the pressure of gaseous hydrogen (GH2) in the small LH2 tank increased to roughly 0.67 MPaG/h, and the temperature of the GH2 in the small LH2 tank increased at the position of gaseous hydrogen at roughly 1.0 K/min when the maximum rolling angle was 5°; the average rolling and liquid-oscillation periods were 114 and 118 s, respectively, as detected by the MgB2 level sensors, which therefore detected a long-period LH2 wave due to the ship’s motion.
- 21 September 2018
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 57 (41) , 13753-13758
Solventless Synthesis of Core–Shell LiFePO4/Carbon Composite for Lithium-Ion Battery Cathodes by Direct Pyrolysis of Coronene
- 21 September 2018
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 57 (41) , 13753-13758
Solventless Synthesis of Core–Shell LiFePO4/Carbon Composite for Lithium-Ion Battery Cathodes by Direct Pyrolysis of Coronene
- 14 August 2017
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 30 (9) , 095012
High transport J c in stainless steel/Ag-Sn double sheathed Ba122 tapes
In this study, we report that the transport critical current density J c of Ba122 tapes can be significantly enhanced by using the harder stainless steel (SS)/Ag-Sn double sheath. A high J c value of 1.4 × 10 5 A cm −2 (at 4.2 K and 10 T) was achieved in SS/Ag-Sn alloyed double sheathed tapes by cold pressing. Even for as-rolled tapes, the J c exceeds the practical level of 10 5 A cm −2 in magnetic fields up to 10 T. More interestingly, a high J c value of 5.5 × 10 4 A cm −2 at 10 T was obtained by a heat treatment with a very low temperature of 550 °C. The microstructure investigations reveal that the higher core density of the Ba122 tapes with uniform deformation and better grain alignment are responsible for the superior J c -field performance.
- 14 August 2017
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 30 (9) , 095012
High transport J c in stainless steel/Ag-Sn double sheathed Ba122 tapes
In this study, we report that the transport critical current density J c of Ba122 tapes can be significantly enhanced by using the harder stainless steel (SS)/Ag-Sn double sheath. A high J c value of 1.4 × 10 5 A cm −2 (at 4.2 K and 10 T) was achieved in SS/Ag-Sn alloyed double sheathed tapes by cold pressing. Even for as-rolled tapes, the J c exceeds the practical level of 10 5 A cm −2 in magnetic fields up to 10 T. More interestingly, a high J c value of 5.5 × 10 4 A cm −2 at 10 T was obtained by a heat treatment with a very low temperature of 550 °C. The microstructure investigations reveal that the higher core density of the Ba122 tapes with uniform deformation and better grain alignment are responsible for the superior J c -field performance.
- 16 May 2017
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 30 (6) , 065005
Improvement in microstructure and superconducting properties of single-filament powder-in-tube MgB 2 wires by cold working with a swaging machine
We investigated the influence of the mechanical deformation method of wire fabrication on the microstructure and superconducting properties of single-filament in situ powder-in-tube (PIT) MgB 2 wires. We employed three deformation methods to fabricate the wires: only swaging, groove rolling + roller drawing, and groove rolling + conventional drawing. We found that cold working by swaging has three advantages over the groove rolling + drawing method: (1) improved uniformity of the MgB 2 core along the longitudinal direction; (2) higher mass density of the Mg + B (MgB 2 ) core before (after) heat treatment (HT); and (3) well-developed fiber structures of Mg (MgB 2 ) before (after) HT. These three factors greatly enhanced the critical current density ( J c ) values of PIT MgB 2 wires. The highest J c values were obtained through mechanical deformation by swaging for both pure and carbon-doped wires. A J c value of 3.5 × 10 4 A cm −2 and an engineering critical current density ( J e ) of 1.1 × 10 4 A cm −2 were recorded at 4.2 K and 10 T for a swaged wire of 4.5%-carbon-coated boron powder heat-treated at 600 °C for 1 h.
- 16 May 2017
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 30 (6) , 065005
Improvement in microstructure and superconducting properties of single-filament powder-in-tube MgB 2 wires by cold working with a swaging machine
We investigated the influence of the mechanical deformation method of wire fabrication on the microstructure and superconducting properties of single-filament in situ powder-in-tube (PIT) MgB 2 wires. We employed three deformation methods to fabricate the wires: only swaging, groove rolling + roller drawing, and groove rolling + conventional drawing. We found that cold working by swaging has three advantages over the groove rolling + drawing method: (1) improved uniformity of the MgB 2 core along the longitudinal direction; (2) higher mass density of the Mg + B (MgB 2 ) core before (after) heat treatment (HT); and (3) well-developed fiber structures of Mg (MgB 2 ) before (after) HT. These three factors greatly enhanced the critical current density ( J c ) values of PIT MgB 2 wires. The highest J c values were obtained through mechanical deformation by swaging for both pure and carbon-doped wires. A J c value of 3.5 × 10 4 A cm −2 and an engineering critical current density ( J e ) of 1.1 × 10 4 A cm −2 were recorded at 4.2 K and 10 T for a swaged wire of 4.5%-carbon-coated boron powder heat-treated at 600 °C for 1 h.
- 20 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 27 (10518223) , 1
Dynamic Level-Detecting Characteristics of External-Heating-Type MgB2 Liquid Hydrogen Level Sensors under Liquid Level Oscillation and Its Application to Sloshing Measurement
To establish the worldwide storage and marine transportation of hydrogen, it is important to develop liquid hydrogen tanks/carriers as well as a long level sensor such as a superconducting magnesium diboride (MgB2) level sensor. An external-heating-type MgB2 level sensor is expected to be an excellent choice for liquid hydrogen because of its high linearity, resolution, and reproducibility. The dynamic level-detecting characteristics of three 500-mm-long MgB2 level sensors have been evaluated under conditions of oscillating liquid level using an optical cryostat and a high-speed microscope. The response time to variations of the liquid hydrogen level is about 0.1 s, and the difference between the level read optically and that detected by the MgB2 level sensors is about 5 mm under these conditions. Thus, the MgB2 level sensors have superior response performance for the sloshing measurement of liquid hydrogen.
- 20 December 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 27 (10518223) , 1
Dynamic Level-Detecting Characteristics of External-Heating-Type MgB2 Liquid Hydrogen Level Sensors under Liquid Level Oscillation and Its Application to Sloshing Measurement
To establish the worldwide storage and marine transportation of hydrogen, it is important to develop liquid hydrogen tanks/carriers as well as a long level sensor such as a superconducting magnesium diboride (MgB2) level sensor. An external-heating-type MgB2 level sensor is expected to be an excellent choice for liquid hydrogen because of its high linearity, resolution, and reproducibility. The dynamic level-detecting characteristics of three 500-mm-long MgB2 level sensors have been evaluated under conditions of oscillating liquid level using an optical cryostat and a high-speed microscope. The response time to variations of the liquid hydrogen level is about 0.1 s, and the difference between the level read optically and that detected by the MgB2 level sensors is about 5 mm under these conditions. Thus, the MgB2 level sensors have superior response performance for the sloshing measurement of liquid hydrogen.
- 17 October 2016
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 29 (11) , 113004
The development of MgB2superconducting wires fabricated with an internal Mg diffusion (IMD) process
In this review, we introduce the development of internal Mg diffusion (IMD)-processed MgB 2 superconducting wires. First, a brief history of the IMD method (which has been given different names by different groups) is introduced and the mechanism of IMD MgB 2 wire is discussed. Second, factors related to J c and J e including: boron (B) powder and carbon (C) addition, the ‘effective MgB 2 density’ (the MgB 2 layer excluding pores, unreacted B particles, MgO, and other impurities), grain size, flux pinning, and connectivity, maximum Mg infiltration distance, B layer thickness and wire diameter, along with other factors such as heat treatment conditions, sheath materials, pressure, and chemical addition are discussed. Third, fabrication processes for IMD long wires, IMD multi-filament wires, and a hybrid method combining IMD and PIT processes are introduced. Fourth, other research related to practical applications, such as the mechanical properties, AC loss of IMD MgB 2 wires are introduced. Finally, future work, including the enhancement of J c (especially J c at 20–30 K) and the superconducting joint of IMD MgB 2 wire are discussed.
- 17 October 2016
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 29 (11) , 113004
The development of MgB2superconducting wires fabricated with an internal Mg diffusion (IMD) process
In this review, we introduce the development of internal Mg diffusion (IMD)-processed MgB 2 superconducting wires. First, a brief history of the IMD method (which has been given different names by different groups) is introduced and the mechanism of IMD MgB 2 wire is discussed. Second, factors related to J c and J e including: boron (B) powder and carbon (C) addition, the ‘effective MgB 2 density’ (the MgB 2 layer excluding pores, unreacted B particles, MgO, and other impurities), grain size, flux pinning, and connectivity, maximum Mg infiltration distance, B layer thickness and wire diameter, along with other factors such as heat treatment conditions, sheath materials, pressure, and chemical addition are discussed. Third, fabrication processes for IMD long wires, IMD multi-filament wires, and a hybrid method combining IMD and PIT processes are introduced. Fourth, other research related to practical applications, such as the mechanical properties, AC loss of IMD MgB 2 wires are introduced. Finally, future work, including the enhancement of J c (especially J c at 20–30 K) and the superconducting joint of IMD MgB 2 wire are discussed.
- Open Access
Novel nanometer-level uniform amorphous carbon coating for boron powders by direct pyrolysis of coronene without solvent
A 3 nm coronene coating and a 4 nm amorphous carbon coating with uniform shell-core encapsulation structure for nanosized boron (B) powders are formed by a simple process, where coronene is directly mixing with boron particles without a solvent, and heated at 520 {\deg}C for 1 h or at 630 {\deg}C for 3 h in a vacuum-sealed silica tube. Coronene has a melting point lower than its decomposition temperature, which enables liquid coronene to cover B particles by liquid diffusion and penetration without the need for a solvent. The diffusion and penetration of coronene can extend to the boundaries of particles and inside agglomerated nanoparticles to form a complete shell-core encapsulated structure. As the temperature is increased, thermal decomposition of coronene on the B particles results in the formation of a uniform amorphous carbon coating layer. This novel and simple nanometer-level uniform amorphous carbon coating method is possibly applied to many other powders, thus it has potential applications in many fields with low cost.
Open AccessNovel nanometer-level uniform amorphous carbon coating for boron powders by direct pyrolysis of coronene without solvent
A 3 nm coronene coating and a 4 nm amorphous carbon coating with uniform shell-core encapsulation structure for nanosized boron (B) powders are formed by a simple process, where coronene is directly mixing with boron particles without a solvent, and heated at 520 {\deg}C for 1 h or at 630 {\deg}C for 3 h in a vacuum-sealed silica tube. Coronene has a melting point lower than its decomposition temperature, which enables liquid coronene to cover B particles by liquid diffusion and penetration without the need for a solvent. The diffusion and penetration of coronene can extend to the boundaries of particles and inside agglomerated nanoparticles to form a complete shell-core encapsulated structure. As the temperature is increased, thermal decomposition of coronene on the B particles results in the formation of a uniform amorphous carbon coating layer. This novel and simple nanometer-level uniform amorphous carbon coating method is possibly applied to many other powders, thus it has potential applications in many fields with low cost.
- Open Access
High transport Jc in magnetic fields up to 28 T of stainless steel/Ag double sheathed Ba122 tapes fabricated by scalable rolling process
The recently discovered iron-based superconductors with very high upper critical field and small anisotropy have been regarded as a potential candidate material for high field applications. However, enhancements of superconducting properties are still needed to boost the successful use of iron-based superconductors in such applications. Here, we propose a new sheath architecture of stainless steel (SS)/Ag double sheath and investigate its influence on the microstructures and Jc-H property. We found that the transport Jc-H curves for rolled and pressed tapes both show extremely small magnetic field dependence and exceed 3*10^4A/cm^2 under 28 T, which are much higher than those of low-temperature superconductors. More interestingly, 12 cm long rolled tape shows very high homogeneity and sustains Jc as high as 7.7*10^4 A/cm^2 at 10 T. These are the highest values reported so far for iron-based superconducting wires fabricated by scalable rolling process. The microstructure investigations indicate that such high Jc was achieved by higher density of the core and uniform deformation resulting better texturing. These results indicate that our process is very promising for fabricating long Ba122 wires for high field magnet, i.e. above 20 T.
Open AccessHigh transport Jc in magnetic fields up to 28 T of stainless steel/Ag double sheathed Ba122 tapes fabricated by scalable rolling process
The recently discovered iron-based superconductors with very high upper critical field and small anisotropy have been regarded as a potential candidate material for high field applications. However, enhancements of superconducting properties are still needed to boost the successful use of iron-based superconductors in such applications. Here, we propose a new sheath architecture of stainless steel (SS)/Ag double sheath and investigate its influence on the microstructures and Jc-H property. We found that the transport Jc-H curves for rolled and pressed tapes both show extremely small magnetic field dependence and exceed 3*10^4A/cm^2 under 28 T, which are much higher than those of low-temperature superconductors. More interestingly, 12 cm long rolled tape shows very high homogeneity and sustains Jc as high as 7.7*10^4 A/cm^2 at 10 T. These are the highest values reported so far for iron-based superconducting wires fabricated by scalable rolling process. The microstructure investigations indicate that such high Jc was achieved by higher density of the core and uniform deformation resulting better texturing. These results indicate that our process is very promising for fabricating long Ba122 wires for high field magnet, i.e. above 20 T.
- Open Access
- 11 February 2014
- Published by Springer Nature in Scientific Reports
- Vol. 4 (1) , 4065
Achievement of practical level critical current densities in Ba1−xKxFe2As2/Ag tapes by conventional cold mechanical deformation
The recently discovered iron-based superconductors are potential candidates for high-field magnet applications. However, the critical current densities (Jc) of iron-based superconducting wires remain far below the level needed for practical applications. Here, we show that the transport Jc of Ba1−xKxFe2As2/Ag tapes is significantly enhanced by the combination process of cold flat rolling and uniaxial pressing. At 4.2 K, Jc exceeds the practical level of 105 A/cm2 in magnetic fields up to 6 T. The Jc-H curve shows extremely small magnetic field dependence and maintains a high value of 8.6 × 104 A/cm2 in 10 T. These are the highest values reported so far for iron-based superconducting wires. Hardness measurements and microstructure investigations reveal that the superior Jc in our samples is due to the high core density, more textured grains, and a change in the microcrack structure. These results indicate that iron-based superconductors are very promising for high magnetic field applications.
- 11 February 2014
- Published by Springer Nature in Scientific Reports
- Vol. 4 (1) , 4065
Open AccessAchievement of practical level critical current densities in Ba1−xKxFe2As2/Ag tapes by conventional cold mechanical deformation
The recently discovered iron-based superconductors are potential candidates for high-field magnet applications. However, the critical current densities (Jc) of iron-based superconducting wires remain far below the level needed for practical applications. Here, we show that the transport Jc of Ba1−xKxFe2As2/Ag tapes is significantly enhanced by the combination process of cold flat rolling and uniaxial pressing. At 4.2 K, Jc exceeds the practical level of 105 A/cm2 in magnetic fields up to 6 T. The Jc-H curve shows extremely small magnetic field dependence and maintains a high value of 8.6 × 104 A/cm2 in 10 T. These are the highest values reported so far for iron-based superconducting wires. Hardness measurements and microstructure investigations reveal that the superior Jc in our samples is due to the high core density, more textured grains, and a change in the microcrack structure. These results indicate that iron-based superconductors are very promising for high magnetic field applications.