Yuejun Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yuejun Zhang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Xiao-Xiao Li
2 shared publications- Xu Jia
School of Chemistry and Chemical Engineering Nanjing University of Science and Technology Nanjing China
2 shared publications - Yikai Yu
School of Chemical Engineering, Jiangxi Normal University, Nanchang, China
2 shared publications Bin Sun
1 shared publication- Ch. Liu
School of Chemical Engineering, Nanjing University of Science & Technology, 200 Xiao Ling Wei, Nanjing 210094, China;;
1 shared publication Cheng Liu
1 shared publication
Latest Publications
- 13 June 2016
- Published by Springer Nature in Polymer Bulletin
- Vol. 73 (8) , 2373-2390
A biocompatible glucose-containing ABC block terpolymer: synthesis, characterization and its properties in solution
- 13 June 2016
- Published by Springer Nature in Polymer Bulletin
- Vol. 73 (8) , 2373-2390
A biocompatible glucose-containing ABC block terpolymer: synthesis, characterization and its properties in solution
- 2 November 2012
- Published by Wiley in CLEAN – Soil, Air, Water
- Vol. 41 (1) , 37-42
Bacteria‐removing and Bactericidal Efficiencies of PDADMAC Composite Coagulants in Enhanced Coagulation Treatment
Enhanced coagulation treatment of bacteria‐containing raw water was studied by using three series of composite coagulants, that were prepared by combining polydiallyldimethylammonium chloride (PDADMAC) with different intrinsic viscosity values (0.55–2.47 dL/g) and mass percentages (5–20%) with polyaluminum chloride (PAC), aluminum sulfate (AS), and the composite of aluminum sulfate and ferric chloride (A‐F), respectively. The coagulants were tested by jar tests for the efficiencies to remove bacteria in raw water and to kill bacteria in settled sludge. It was found that when the residual turbidity of supernatant after sedimentation reached the control standard of 2 NTU in drinking water plant, the bacteria‐removing rates of PAC, AS, and A‐F were 92.22, 92.60, and 94.99%, respectively, and the bactericidal rates were 2.52, 1.22, and 2.94%, respectively. Contrastively, the bacteria‐removing rates of PAC/PDADMAC, AS/PDADMAC, and A‐F/PDADMAC could reach 95.45, 96.90, and 98.89%, respectively, and the bactericidal rates could reach 86.60, 91.81, and 96.98%, respectively. It could be deduced from the results that the bactericidal efficiencies of composite coagulants stemmed from the bactericidal action of PDADMAC, and the inorganic coagulants had little bactericidal function.
- 2 November 2012
- Published by Wiley in CLEAN – Soil, Air, Water
- Vol. 41 (1) , 37-42
Bacteria‐removing and Bactericidal Efficiencies of PDADMAC Composite Coagulants in Enhanced Coagulation Treatment
Enhanced coagulation treatment of bacteria‐containing raw water was studied by using three series of composite coagulants, that were prepared by combining polydiallyldimethylammonium chloride (PDADMAC) with different intrinsic viscosity values (0.55–2.47 dL/g) and mass percentages (5–20%) with polyaluminum chloride (PAC), aluminum sulfate (AS), and the composite of aluminum sulfate and ferric chloride (A‐F), respectively. The coagulants were tested by jar tests for the efficiencies to remove bacteria in raw water and to kill bacteria in settled sludge. It was found that when the residual turbidity of supernatant after sedimentation reached the control standard of 2 NTU in drinking water plant, the bacteria‐removing rates of PAC, AS, and A‐F were 92.22, 92.60, and 94.99%, respectively, and the bactericidal rates were 2.52, 1.22, and 2.94%, respectively. Contrastively, the bacteria‐removing rates of PAC/PDADMAC, AS/PDADMAC, and A‐F/PDADMAC could reach 95.45, 96.90, and 98.89%, respectively, and the bactericidal rates could reach 86.60, 91.81, and 96.98%, respectively. It could be deduced from the results that the bactericidal efficiencies of composite coagulants stemmed from the bactericidal action of PDADMAC, and the inorganic coagulants had little bactericidal function.
- Open Access
- 20 March 2012
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 38 (8) , 2097-2109
Controlled synthesis of novel reactive cationic copolymers of 3-chloro-2-hydroxypropylmethyldiallylammonium chloride and dimethyldiallylammonium chloride [P(CMDA-DMDAAC)s]: designed as useful polycationic dye-fixatives on cotton fabric
- 20 March 2012
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 38 (8) , 2097-2109
Open AccessControlled synthesis of novel reactive cationic copolymers of 3-chloro-2-hydroxypropylmethyldiallylammonium chloride and dimethyldiallylammonium chloride [P(CMDA-DMDAAC)s]: designed as useful polycationic dye-fixatives on cotton fabric
- 16 January 2012
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 125 (2) , 1636-1641
Kinetic study of the polymerization of dimethyldiallylammonium chloride and acrylamide
- 16 January 2012
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 125 (2) , 1636-1641
Kinetic study of the polymerization of dimethyldiallylammonium chloride and acrylamide
- 15 December 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 125 (1) , 1-9
Effects of maintaining temperature and time on properties and structures of poly(dimethyldiallylammonium chloride)
Effects of maintaining temperature (T3) and time (t) on properties and structures of product poly(dimethyldiallylammonium chloride) (PDMDAAC) are researched in this article. The results showed that higher the T3 shorter the time t needed for polymer products' intrinsic viscosity ([η]) and monomer conversion (Conv.) to reach their maximum values. The maximum [η] was 4.69 dL g−1 and corresponding Conv. was 100.00%, when t = 96 h and T3 = 55°C. The reaction phenomena and products' FTIR and NMR spectra indicated the possible reasons for the increase of [η], the formation of branched and crosslinked products after the conversion was more than 100.00% in T3 term were the results of polymerization happened among the residual monomers, hanging and terminal double bonds. Compared with solubility of products, it was found that the time needed for dissolving the linear, branched, and crosslinked PDMDAAC products increased in turn, whereas their dissolved amount decreased reversely. The linear product's Mw, Mw/Mn, and Rg measured by GPC‐MALLS were 4.169 × 106, 5.109, and 127.7 nm, respectively. Meanwhile, the linear and crosslinked products were characterized by DTA‐TG. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012
- 15 December 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 125 (1) , 1-9
Effects of maintaining temperature and time on properties and structures of poly(dimethyldiallylammonium chloride)
Effects of maintaining temperature (T3) and time (t) on properties and structures of product poly(dimethyldiallylammonium chloride) (PDMDAAC) are researched in this article. The results showed that higher the T3 shorter the time t needed for polymer products' intrinsic viscosity ([η]) and monomer conversion (Conv.) to reach their maximum values. The maximum [η] was 4.69 dL g−1 and corresponding Conv. was 100.00%, when t = 96 h and T3 = 55°C. The reaction phenomena and products' FTIR and NMR spectra indicated the possible reasons for the increase of [η], the formation of branched and crosslinked products after the conversion was more than 100.00% in T3 term were the results of polymerization happened among the residual monomers, hanging and terminal double bonds. Compared with solubility of products, it was found that the time needed for dissolving the linear, branched, and crosslinked PDMDAAC products increased in turn, whereas their dissolved amount decreased reversely. The linear product's Mw, Mw/Mn, and Rg measured by GPC‐MALLS were 4.169 × 106, 5.109, and 127.7 nm, respectively. Meanwhile, the linear and crosslinked products were characterized by DTA‐TG. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012
- Open Access
- 1 August 2011
- Published by Wiley in Journal of the Chinese Chemical Society
- Vol. 58 (4) , 428-434
Controlled-synthesis of Slightly Crosslinked Poly(dimethyldiallylammonium chloride)s Used as Useful Polycationic Dye-fixatives on Cotton Fabric
- 1 August 2011
- Published by Wiley in Journal of the Chinese Chemical Society
- Vol. 58 (4) , 428-434
Open AccessControlled-synthesis of Slightly Crosslinked Poly(dimethyldiallylammonium chloride)s Used as Useful Polycationic Dye-fixatives on Cotton Fabric
- 5 August 2010
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 22 (12) , 2543-2549
Structure-controlled synthesis of novel soluble and thermally stable poly (aryl ether nitrile ether ketone ketone)/poly (aryl ether nitrile ether ketone biphenyl ketone) copolymers by electrophilic polycondensation
- 5 August 2010
- Published by Wiley in Polymers for Advanced Technologies
- Vol. 22 (12) , 2543-2549
Structure-controlled synthesis of novel soluble and thermally stable poly (aryl ether nitrile ether ketone ketone)/poly (aryl ether nitrile ether ketone biphenyl ketone) copolymers by electrophilic polycondensation
- 1 July 2010
- Published by IWA Publishing in Water Science & Technology
- Vol. 62 (2) , 330-339
Performance of PAC/PDM composite coagulants for removal of algae from Lake Taihu waters in summer
The enhanced coagulation of algae-rich raw water from Lake Taihu in summer was studied by use of composite coagulants. The composite coagulants were composed of polyaluminum chloride (PAC) and polydimethyldiallylammonium chloride (PDM) with various intrinsic viscosity values (0.55-3.99 dL/g) and different mass percentages (5-20%) in the formulation. For raw water with temperature of 28-29 degrees C and algae content of 3.60x10(4)-3.70x10(4) cells/ml, the algae-removal rates of 89.0% and 89.3-93.1% could be realized by using PAC and PAC/PDM (0.55/5%-3.99/20%) with dosages of 8.37 mg/L and 5.93-3.58 mg/L, respectively, when 2 NTU residual turbidity of treated water after sedimentation was required. Compared with using PAC only, the removal rate of CODMn using PAC/PDM increased at least 4.4% when the dosage was 8 mg/L, and increased at least 5.0% when the dosage was 10 mg/L. The composite coagulants could still function well when raw water quality deteriorated and algae content reached 8.00x10(4) cells/ml. The enhanced coagulation efficiency of PAC/PDM (0.55/5%) could be better than that of PAC combined with prechlorination process when the same dosages are used.
- 1 July 2010
- Published by IWA Publishing in Water Science & Technology
- Vol. 62 (2) , 330-339
Performance of PAC/PDM composite coagulants for removal of algae from Lake Taihu waters in summer
The enhanced coagulation of algae-rich raw water from Lake Taihu in summer was studied by use of composite coagulants. The composite coagulants were composed of polyaluminum chloride (PAC) and polydimethyldiallylammonium chloride (PDM) with various intrinsic viscosity values (0.55-3.99 dL/g) and different mass percentages (5-20%) in the formulation. For raw water with temperature of 28-29 degrees C and algae content of 3.60x10(4)-3.70x10(4) cells/ml, the algae-removal rates of 89.0% and 89.3-93.1% could be realized by using PAC and PAC/PDM (0.55/5%-3.99/20%) with dosages of 8.37 mg/L and 5.93-3.58 mg/L, respectively, when 2 NTU residual turbidity of treated water after sedimentation was required. Compared with using PAC only, the removal rate of CODMn using PAC/PDM increased at least 4.4% when the dosage was 8 mg/L, and increased at least 5.0% when the dosage was 10 mg/L. The composite coagulants could still function well when raw water quality deteriorated and algae content reached 8.00x10(4) cells/ml. The enhanced coagulation efficiency of PAC/PDM (0.55/5%) could be better than that of PAC combined with prechlorination process when the same dosages are used.
- 1 June 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 118 (2) , 1152-1159
Preparation and characterization of poly(dimethyldiallylammonium chloride) with high molar mass using high purity industrial monomer
A preparation method for high molar mass poly(dimethyldiallylammonium chloride) (PDMDAAC) is reported in this article. PDMDAAC was prepared by using the high purity industrial grade dimethyldiallylammonium chloride (DMDAAC) monomer from one‐step method and ammonium persulphate (APS) as the initiator. The initiator was added all at once and the reaction temperature was increased stepwise to complete the polymerization gradually. The effects of several polymerization condition variables on the intrinsic viscosity value ([η]) and monomer conversion rate (Conv.) of product PDMDAAC were investigated, respectively. The variables included: T1 (42.0 to 52.0°C), T2 (47.5 to 57.5°C), T3 (55.0 to 75.0°C), m(DMDAAC) (60.0 to 70.0%), m(APS) : m(DMDAAC) (0.25 to 0.45%), m(Na4EDTA) : m(DMDAAC) (0 to 0.0071%). Under an optimum condition of T1 = 46.0°C, T2 = 52.5°C, T3 = 65.0°C, m(DMDAAC) = 65.0%, m(APS) : m(DMDAAC) = 0.35%, m(Na4EDTA) : m(DMDAAC) = 0.0035%, the maximum [η] of obtained product PDMDAAC reached 3.43 dL/g, at a Conv. of 100.00%. The Mw of the product measured with GPC‐MALLS was 1.034 × 106, polydespersity Mw/Mn was 2.421, and the Rg was 60.3 nm. The structure and properties of products were characterized by FTIR and NMR. Thermal decomposition was determined by TGA‐DSC. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010
- 1 June 2010
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 118 (2) , 1152-1159
Preparation and characterization of poly(dimethyldiallylammonium chloride) with high molar mass using high purity industrial monomer
A preparation method for high molar mass poly(dimethyldiallylammonium chloride) (PDMDAAC) is reported in this article. PDMDAAC was prepared by using the high purity industrial grade dimethyldiallylammonium chloride (DMDAAC) monomer from one‐step method and ammonium persulphate (APS) as the initiator. The initiator was added all at once and the reaction temperature was increased stepwise to complete the polymerization gradually. The effects of several polymerization condition variables on the intrinsic viscosity value ([η]) and monomer conversion rate (Conv.) of product PDMDAAC were investigated, respectively. The variables included: T1 (42.0 to 52.0°C), T2 (47.5 to 57.5°C), T3 (55.0 to 75.0°C), m(DMDAAC) (60.0 to 70.0%), m(APS) : m(DMDAAC) (0.25 to 0.45%), m(Na4EDTA) : m(DMDAAC) (0 to 0.0071%). Under an optimum condition of T1 = 46.0°C, T2 = 52.5°C, T3 = 65.0°C, m(DMDAAC) = 65.0%, m(APS) : m(DMDAAC) = 0.35%, m(Na4EDTA) : m(DMDAAC) = 0.0035%, the maximum [η] of obtained product PDMDAAC reached 3.43 dL/g, at a Conv. of 100.00%. The Mw of the product measured with GPC‐MALLS was 1.034 × 106, polydespersity Mw/Mn was 2.421, and the Rg was 60.3 nm. The structure and properties of products were characterized by FTIR and NMR. Thermal decomposition was determined by TGA‐DSC. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010
- 15 April 2009
- Vol. 30 (4) , 1023-8
[Algae-removal effect of AS/PDM composite coagulants to winter Taihu Lake raw water].
The series of stable AS/PDM composite coagulants prepared by polydimethyldiallylammonium chloride (PDM) and aluminium sulphate (AS) were used to research the algae-removal effect to winter Taihu Lake raw water. The effects of dosage of composite coagulants, composite mass ratios (20:1-5:1) of AS and PDM, intrinsic viscosity values (0.55-3.99 dL/g) of PDM on algae-removal rates were studied through coagulation and algae-removal experiments. The feasibility of using composite coagulants to substitute prechlorination process was analysed. The results show that when residual turbidity of 2 NTU to water after coagulation and sediment is required by water plant, the dosage (based on Al2O3) of AS, AS/PDM (0.55/20:1-3.99/5:1) composite coagulants are 4.24 mg/L, 3.96-1.87 mg/L, and the algae-removal rates are 83.00%, 87.52%-90.93% respectively. When dosage to raw water are 4.24 mg/L, the algae-removal rates of AS, AS/PDM (0.55/20:1-3.99/5:1) composite coagulants are 83.00%, 88.29%-97.66%, and the residual turbidities are 2.00 NTU, 1.76-0.43 NTU respectively. When dosage to chlorine-added water are 4.50 mg/L, the treatment effect of AS/PDM (1.53/10:1) composite coagulant to raw water is better than that of AS to chlorine-added water, and the treatment effect of AS/PDM (3.99/5:1) composite coagulant to raw water is better than that of AS, AS/PDM (0.55/20:1) and AS/PDM (1.53/10:1) composite coagulants to chlorine-added water. So using AS/PDM composite coagulants can enhance evidently the treatment effect of AS to winter Taihu Lake raw water. Compared with using AS solely, the dosage of AS in composite coagulants are saved when the residual turbidities are required in same level, and the treatment effect of AS is enhanced when the dosage of AS in composite coagulants are same as that of using AS solely. Moreover, using composite coagulants can replace the part chlorine-added function on increasing coagulation and algae-removal in prechlorination process and profitably increases safety of drinking water quality.
- 15 April 2009
- Vol. 30 (4) , 1023-8
[Algae-removal effect of AS/PDM composite coagulants to winter Taihu Lake raw water].
The series of stable AS/PDM composite coagulants prepared by polydimethyldiallylammonium chloride (PDM) and aluminium sulphate (AS) were used to research the algae-removal effect to winter Taihu Lake raw water. The effects of dosage of composite coagulants, composite mass ratios (20:1-5:1) of AS and PDM, intrinsic viscosity values (0.55-3.99 dL/g) of PDM on algae-removal rates were studied through coagulation and algae-removal experiments. The feasibility of using composite coagulants to substitute prechlorination process was analysed. The results show that when residual turbidity of 2 NTU to water after coagulation and sediment is required by water plant, the dosage (based on Al2O3) of AS, AS/PDM (0.55/20:1-3.99/5:1) composite coagulants are 4.24 mg/L, 3.96-1.87 mg/L, and the algae-removal rates are 83.00%, 87.52%-90.93% respectively. When dosage to raw water are 4.24 mg/L, the algae-removal rates of AS, AS/PDM (0.55/20:1-3.99/5:1) composite coagulants are 83.00%, 88.29%-97.66%, and the residual turbidities are 2.00 NTU, 1.76-0.43 NTU respectively. When dosage to chlorine-added water are 4.50 mg/L, the treatment effect of AS/PDM (1.53/10:1) composite coagulant to raw water is better than that of AS to chlorine-added water, and the treatment effect of AS/PDM (3.99/5:1) composite coagulant to raw water is better than that of AS, AS/PDM (0.55/20:1) and AS/PDM (1.53/10:1) composite coagulants to chlorine-added water. So using AS/PDM composite coagulants can enhance evidently the treatment effect of AS to winter Taihu Lake raw water. Compared with using AS solely, the dosage of AS in composite coagulants are saved when the residual turbidities are required in same level, and the treatment effect of AS is enhanced when the dosage of AS in composite coagulants are same as that of using AS solely. Moreover, using composite coagulants can replace the part chlorine-added function on increasing coagulation and algae-removal in prechlorination process and profitably increases safety of drinking water quality.