Junko Matsuda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Junko Matsuda has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Y. Yamada
Superconductivity Research Laboratory, International Superconductivity Technology Center (ISTEC), Koto-ku, Tokyo 135-0062, Japan
4 shared publications- Koichi Nakaoka
National Institute of Advanced Industrial Science and Technology, Tsukuba, Japan
3 shared publications T. Izumi
Superconductivity Research Laboratory, International Superconductivity Technology Center (ISTEC), Koto-ku, Tokyo 135-0062, Japan
3 shared publicationsY. Shiohara
Superconductivity Research Laboratory, International Superconductivity Technology Center (ISTEC), Koto-ku, Tokyo 135-0062, Japan
3 shared publicationsK. Nakaoka
Superconductivity Research Laboratory, ISTEC, Shinonome 1-10-13, Koto-ku, Tokyo 135-0062, Japan
2 shared publicationsTeruo Izumi
2 shared publications
Latest Publications
- 23 April 2009
- Published by IOP Publishing in Nanotechnology
- Vol. 20 (20) , 204015
The nanostructure and hydrogenation reaction of Mg50Co50BCC alloy prepared by ball-milling
Mg50Co50 alloy before and after hydrogenation was investigated by means of transmission electron microscopy (TEM). Mg50Co50 alloy before hydrogenation was found to contain crystals not larger than 5 nm in size. Selected-area electron diffraction patterns (SAEDPs) revealed that these nanocrystals have a body-centered cubic (BCC) structure with a lattice parameter of about 0.3 nm. Distribution of Mg and Co elements in the Mg50Co50 alloy was uniform, indicated by energy dispersive x-ray spectroscopy (EDS) analysis. Crystallization and decomposition occurred in the Mg50Co50 alloy during hydrogenation. A large number of crystals larger than 10 nm were observed in the hydrogenated sample. The SAEDPs showed polycrystalline rings corresponding to the BCC phase and the Co metal phase. The existence of Mg-rich Mg-Co crystals and Co particles was also confirmed by TEM-EDS analysis.
- 23 April 2009
- Published by IOP Publishing in Nanotechnology
- Vol. 20 (20) , 204015
The nanostructure and hydrogenation reaction of Mg50Co50BCC alloy prepared by ball-milling
Mg50Co50 alloy before and after hydrogenation was investigated by means of transmission electron microscopy (TEM). Mg50Co50 alloy before hydrogenation was found to contain crystals not larger than 5 nm in size. Selected-area electron diffraction patterns (SAEDPs) revealed that these nanocrystals have a body-centered cubic (BCC) structure with a lattice parameter of about 0.3 nm. Distribution of Mg and Co elements in the Mg50Co50 alloy was uniform, indicated by energy dispersive x-ray spectroscopy (EDS) analysis. Crystallization and decomposition occurred in the Mg50Co50 alloy during hydrogenation. A large number of crystals larger than 10 nm were observed in the hydrogenated sample. The SAEDPs showed polycrystalline rings corresponding to the BCC phase and the Co metal phase. The existence of Mg-rich Mg-Co crystals and Co particles was also confirmed by TEM-EDS analysis.
- 1 December 2008
- Published by Springer Nature in Journal of Materials Research
- Vol. 23 (12) , 3353-3362
Transmission electron microscopic studies on growth mechanism of YBa2Cu3O7−y films formed by advanced trifluoroacetates metalorganic deposition process
Microstructure evolution of YBa2Cu3O7−y (YBCO) films during the two heat-treatments in the advanced trifluoroacetates metalorganic deposition (TFA-MOD) process has been investigated by means of transmission electron microscopy. In the calcination process, precursor films including nanopores were formed through the shrinkage of the film after a remarkable increase of the thickness due to the thermal decomposition of metalorganic salts in the starting solution. During the crystallization process, the densification and shrinkage of the film occurred after agglomeration of nanopores and coarsening of unreacted phase particles such as Y2Cu2O5, CuO, and Ba–O–F in the precursor films. The YBCO films were then epitaxially grown with the remaining unreacted phase particles in the film, finally pores were generated again by a reaction of these unreacted particles to form YBCO accompanied by the volume reduction. It is important to control the densification of precursor films and coarsening of the unreacted phase particles in the crystallization process, to fabricate YBCO final films with fine crystallinity and high critical current values.
- 1 December 2008
- Published by Springer Nature in Journal of Materials Research
- Vol. 23 (12) , 3353-3362
Transmission electron microscopic studies on growth mechanism of YBa2Cu3O7−y films formed by advanced trifluoroacetates metalorganic deposition process
Microstructure evolution of YBa2Cu3O7−y (YBCO) films during the two heat-treatments in the advanced trifluoroacetates metalorganic deposition (TFA-MOD) process has been investigated by means of transmission electron microscopy. In the calcination process, precursor films including nanopores were formed through the shrinkage of the film after a remarkable increase of the thickness due to the thermal decomposition of metalorganic salts in the starting solution. During the crystallization process, the densification and shrinkage of the film occurred after agglomeration of nanopores and coarsening of unreacted phase particles such as Y2Cu2O5, CuO, and Ba–O–F in the precursor films. The YBCO films were then epitaxially grown with the remaining unreacted phase particles in the film, finally pores were generated again by a reaction of these unreacted particles to form YBCO accompanied by the volume reduction. It is important to control the densification of precursor films and coarsening of the unreacted phase particles in the crystallization process, to fabricate YBCO final films with fine crystallinity and high critical current values.
- 15 July 2008
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 468 (14) , 997-1005
Effect of Ba/Y ratio in starting solution on microstructure evolution of YBCO films deposited by advanced TFA-MOD process
- 15 July 2008
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 468 (14) , 997-1005
Effect of Ba/Y ratio in starting solution on microstructure evolution of YBCO films deposited by advanced TFA-MOD process
- 15 July 2008
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 468 (14) , 1017-1023
Microstructure evolution of YBCO films deposited by advanced TFA-MOD process
- 15 July 2008
- Published by Elsevier in Physica C: Superconductivity and its Applications
- Vol. 468 (14) , 1017-1023
Microstructure evolution of YBCO films deposited by advanced TFA-MOD process
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 3317-3320
High Production Rate Process of YBCO Coated Conductors by TFA-MOD Process
Influence of process conditions including water vapor partial pressure, gas flow rate and total annealing pressure on YBa2Cu3O7-y (YBCO) film growth has been investigated in order to clarify the YBCO growth mechanism and to increase the growth rate. YBCO films have been fabricated on a LaAlO3 substrate by metalorganic deposition (MOD) process using tri- fluoroacetates (TFA) as a solute source. It was found that the processing parameters such as high water partial pressure, high diffusion constants due to low total pressure, and high gas flow rate affect the YBCO growth rate. Furthermore, it was empirically suggested that the growth rate of the YBCO film was in proportion to both the square root of water partial pressure and gas flow rate and was in inverse proportion to the one sixth power of the total pressure. The YBCO growth rate of about 2 times as fast as the previous condition was achieved with high performance by optimizing the process parameters.
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 3317-3320
High Production Rate Process of YBCO Coated Conductors by TFA-MOD Process
Influence of process conditions including water vapor partial pressure, gas flow rate and total annealing pressure on YBa2Cu3O7-y (YBCO) film growth has been investigated in order to clarify the YBCO growth mechanism and to increase the growth rate. YBCO films have been fabricated on a LaAlO3 substrate by metalorganic deposition (MOD) process using tri- fluoroacetates (TFA) as a solute source. It was found that the processing parameters such as high water partial pressure, high diffusion constants due to low total pressure, and high gas flow rate affect the YBCO growth rate. Furthermore, it was empirically suggested that the growth rate of the YBCO film was in proportion to both the square root of water partial pressure and gas flow rate and was in inverse proportion to the one sixth power of the total pressure. The YBCO growth rate of about 2 times as fast as the previous condition was achieved with high performance by optimizing the process parameters.
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 3329-3331
Recent Progress on R&D of Advanced TFA-MOD Process for Coated Conductors
The recent progress in R&D of TFA-MOD process for the coated conductors is reviewed. On the effort towards fabricating high Ic tape, a new process to prevent crack formation in the thick film, which is the intermediate annealing between calcination and crystallization steps, was developed. Additionally, control of the composition from the 123 stoichiometric ratio, especially for Ba-poor composition, is found to be effective to improve Jc values of the films. Consequently, the extremely high Ic value of 692 A was obtained. On the other hand, a reel-to-reel system has been applied to fabricate long tapes. The high Ic value of 250 A/cm-w in a 4 m long tape and the reasonable long tape of 25 m with 100 A/cm-w were obtained. Additionally, it was newly found that the humidity control to be low PH 2 O in the coating room is effective to suppressing the degradation of the Jc characterization.
- 23 July 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 17 (2) , 3329-3331
Recent Progress on R&D of Advanced TFA-MOD Process for Coated Conductors
The recent progress in R&D of TFA-MOD process for the coated conductors is reviewed. On the effort towards fabricating high Ic tape, a new process to prevent crack formation in the thick film, which is the intermediate annealing between calcination and crystallization steps, was developed. Additionally, control of the composition from the 123 stoichiometric ratio, especially for Ba-poor composition, is found to be effective to improve Jc values of the films. Consequently, the extremely high Ic value of 692 A was obtained. On the other hand, a reel-to-reel system has been applied to fabricate long tapes. The high Ic value of 250 A/cm-w in a 4 m long tape and the reasonable long tape of 25 m with 100 A/cm-w were obtained. Additionally, it was newly found that the humidity control to be low PH 2 O in the coating room is effective to suppressing the degradation of the Jc characterization.
- 1 July 1997
- Vol. 50 (7) , 640-9
[Antimicrobial activities of roxithromycin against recently obtained clinical isolates].
The purpose of our investigation was to monitor current trends in the susceptibility patterns of clinical bacterial isolates to roxithromycin (RXM). We measured the MICs of macrolide antibiotics, such as RXM, erythromycin (EM), clarithromycin (CAM), rokitamycin (RKM) and midecamycin (MDM), and other classes of antibacterial compounds against various clinical isolates at seven institutions between October and December in 1994 and 1995. RXM had excellent antibacterial activities for S. pyogenes, S. agalactiae, M. (B.) catarrhalis and methicillin sensitive S. aureus. Against methicillin sensitive S. epidermidis, RXM activity was fairly good but about 20% of the strains had MIC > or = 128 micrograms/ml. The activity against S. pneumoniae was not so potent and similar to activities of EM, CAM, MDM, and clindamycin. The vast majority of methicillin resistant S. aureus and S. epidermidis were also resistant to macrolide antibiotics and other classes of compounds tested. In conclusion, RXM is an unique macrolide antibiotic by retaining potent activity against S. pyogenes, S. agalactiae, S. aureus except MRSA, M. (B.) catarrhalis and M. pneumoniae.
- 1 July 1997
- Vol. 50 (7) , 640-9
[Antimicrobial activities of roxithromycin against recently obtained clinical isolates].
The purpose of our investigation was to monitor current trends in the susceptibility patterns of clinical bacterial isolates to roxithromycin (RXM). We measured the MICs of macrolide antibiotics, such as RXM, erythromycin (EM), clarithromycin (CAM), rokitamycin (RKM) and midecamycin (MDM), and other classes of antibacterial compounds against various clinical isolates at seven institutions between October and December in 1994 and 1995. RXM had excellent antibacterial activities for S. pyogenes, S. agalactiae, M. (B.) catarrhalis and methicillin sensitive S. aureus. Against methicillin sensitive S. epidermidis, RXM activity was fairly good but about 20% of the strains had MIC > or = 128 micrograms/ml. The activity against S. pneumoniae was not so potent and similar to activities of EM, CAM, MDM, and clindamycin. The vast majority of methicillin resistant S. aureus and S. epidermidis were also resistant to macrolide antibiotics and other classes of compounds tested. In conclusion, RXM is an unique macrolide antibiotic by retaining potent activity against S. pyogenes, S. agalactiae, S. aureus except MRSA, M. (B.) catarrhalis and M. pneumoniae.