Mohsen Goodarzi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mohsen Goodarzi has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
M. Najafi
Bu Ali Sina Univ, Hamadan, Iran
2 shared publications- Benjamin Mahns
Leibniz Institute for Agricultural Engineering and Bioeconomy, Max-Eyth-Allee 100, 14469 Potsdam-Bornim, Germany
1 shared publication - Hamid Zare Abyaneh
Department of Water Engineering, Faculty of Agriculture Bu‐Ali Sina University Hamedan Iran
1 shared publication M. Hamzeh
1 shared publication- Muhammad Sultan
Department of Agricultural Engineering, Bahauddin Zakariya University, Multan 60800, Pakistan
1 shared publication Nima Eshghabadi
Faculty of Engineering, Bu_Ali Sina University, Hamedan, Iran
1 shared publication
Latest Publications
- Open Access
- 20 May 2026
- Published by Elsevier in SSRN Electronic Journal
Comparative study on performance of two tandem natural draft dry cooling towers with elliptical cross sections
Elliptical periphery radiator installation has been proposed to enhance thermal performance of natural draft dry cooling tower at windy condition. In practice, more than one cooling tower are used. Thermal performances of two cooling towers with elliptical and circular radiator arrangements in tandem configuration have been numerically compared in the present study. Results showed that thermal performance of two cooling towers with elliptical radiator arrangement are greater than those with circular radiator arrangements at wind velocities 7 and 10 m/s. In this range of wind velocity, elliptical cooling towers increases the total thermal performance of the system by 9.8% to 19.8% compared to the corresponding circular towers. Distributed parameters within or across the radiators, in association with velocity vector and temperature distributions in the nearfield airflow showed that there was no indoor airflow crossing out the radiators at low wind speeds. In this range of wind velocity, there is a direct proportionality between the air mass flow rate entering the cooling tower and thermal performance. But, at increased wind velocities (7 and 10 m/s) the indoor airflow crossing some radiators out reverses the proportionality between the air mass flow rate entering the cooling tower and thermal performance over these particular radiators. The sophisticated flow-field between the two cooling towers at high wind velocity increases the mentioned nonproportionality. The onset of such nonproportionality was taken place at lower wind velocity in the elliptical cooling towers compared to the circular ones.
- 20 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessComparative study on performance of two tandem natural draft dry cooling towers with elliptical cross sections
Elliptical periphery radiator installation has been proposed to enhance thermal performance of natural draft dry cooling tower at windy condition. In practice, more than one cooling tower are used. Thermal performances of two cooling towers with elliptical and circular radiator arrangements in tandem configuration have been numerically compared in the present study. Results showed that thermal performance of two cooling towers with elliptical radiator arrangement are greater than those with circular radiator arrangements at wind velocities 7 and 10 m/s. In this range of wind velocity, elliptical cooling towers increases the total thermal performance of the system by 9.8% to 19.8% compared to the corresponding circular towers. Distributed parameters within or across the radiators, in association with velocity vector and temperature distributions in the nearfield airflow showed that there was no indoor airflow crossing out the radiators at low wind speeds. In this range of wind velocity, there is a direct proportionality between the air mass flow rate entering the cooling tower and thermal performance. But, at increased wind velocities (7 and 10 m/s) the indoor airflow crossing some radiators out reverses the proportionality between the air mass flow rate entering the cooling tower and thermal performance over these particular radiators. The sophisticated flow-field between the two cooling towers at high wind velocity increases the mentioned nonproportionality. The onset of such nonproportionality was taken place at lower wind velocity in the elliptical cooling towers compared to the circular ones.
- Open Access
- 17 March 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Impact of radiators periphery arrangement on thermal performance of side-by-side natural draft dry cooling towers under crosswind conditions
- 17 March 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Open AccessImpact of radiators periphery arrangement on thermal performance of side-by-side natural draft dry cooling towers under crosswind conditions
- 13 February 2024
- Published by Elsevier in Ocean Engineering
- Vol. 296
Numerical study on power generation versus force fluctuation of two side-by-side Savonius rotors
- 13 February 2024
- Published by Elsevier in Ocean Engineering
- Vol. 296
Numerical study on power generation versus force fluctuation of two side-by-side Savonius rotors
- Open Access
- 1 January 2022
- Published by Academic World Research in Journal of Applied Fluid Mechanics
- Vol. 15 (1) , 169-178
Stabilizing a Laminar Flow over a Rectangular Cylinder using Two Small Rotating Cylinders
The possibility of suppressing laminar vortex shedding after a rectangular cylinder with a pair of rotating controllers has been investigated for Re=150. Drag and lift coefficients of the rectangular cylinder have been measured at different positions of the controller system. Numerical results show that the controller system suppresses the vortex shedding completely when installing at some suitable positions. It was found that the controller system affects the vorticity intensity in the separation bubbles at these suitable positions. The controller system may completely eliminate the separation bubble or may make them remain in attached to the cylinder. Besides, the effectiveness sensitivity of the controller system to its rotation rate and Reynolds number was analyzed when installing at the edge of the cylinder boundary layer where its position is denoted by (r/a=2,q=40o). These analyses show that the controller system can still suppress the laminar vortex shedding completely when the rotation rate of the controller system and Reynolds number of the incoming flow change by less than 50%.
- 1 January 2022
- Published by Academic World Research in Journal of Applied Fluid Mechanics
- Vol. 15 (1) , 169-178
Open AccessStabilizing a Laminar Flow over a Rectangular Cylinder using Two Small Rotating Cylinders
The possibility of suppressing laminar vortex shedding after a rectangular cylinder with a pair of rotating controllers has been investigated for Re=150. Drag and lift coefficients of the rectangular cylinder have been measured at different positions of the controller system. Numerical results show that the controller system suppresses the vortex shedding completely when installing at some suitable positions. It was found that the controller system affects the vorticity intensity in the separation bubbles at these suitable positions. The controller system may completely eliminate the separation bubble or may make them remain in attached to the cylinder. Besides, the effectiveness sensitivity of the controller system to its rotation rate and Reynolds number was analyzed when installing at the edge of the cylinder boundary layer where its position is denoted by (r/a=2,q=40o). These analyses show that the controller system can still suppress the laminar vortex shedding completely when the rotation rate of the controller system and Reynolds number of the incoming flow change by less than 50%.
- Open Access
- 1 November 2021
- Published by Elsevier in Energy Reports
- Vol. 7, 4530-4539
Energy and exergy analyses of a new atmospheric regenerative Brayton and Inverse Brayton cycle
- 1 November 2021
- Published by Elsevier in Energy Reports
- Vol. 7, 4530-4539
Open AccessEnergy and exergy analyses of a new atmospheric regenerative Brayton and Inverse Brayton cycle
- 8 September 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (1) , 11168-11187
Numerical assessment of the effect of different end-plates on the performance of a finite-height Savonius turbine
I.e. semi-circular and circular end-plates, and also a new proposed one, which is called quarter-spherical end-plate. The effectiveness of the end plates are measured and compared with the benchmark case, i.e. without end-plate. Computed results show that all end-plates increase the power coefficient of the rotor, among them the circular end-plate does considerably. The rotor with circular end-plate generates positive power coefficient even at tip–speed ratio (TSR) greater than 1.0, whereas the other rotors do not. Circular end-plate increases the power coefficient of the wind turbine by 84% at TSR = 0.6, the TSR corresponding to the greatest power coefficients of all studied rotors, and averagely by 126% in the range 0.4<TSR<0.8. Unfortunately, the rotor with circular end-plate faces with the greatest levels of the drag and lift forces exerting on the rotor shaft. Introducing some designing indices shows that a rotor with quarter-spherical end-plate can be a good alternative for one with circular end-plate.
- 8 September 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (1) , 11168-11187
Numerical assessment of the effect of different end-plates on the performance of a finite-height Savonius turbine
I.e. semi-circular and circular end-plates, and also a new proposed one, which is called quarter-spherical end-plate. The effectiveness of the end plates are measured and compared with the benchmark case, i.e. without end-plate. Computed results show that all end-plates increase the power coefficient of the rotor, among them the circular end-plate does considerably. The rotor with circular end-plate generates positive power coefficient even at tip–speed ratio (TSR) greater than 1.0, whereas the other rotors do not. Circular end-plate increases the power coefficient of the wind turbine by 84% at TSR = 0.6, the TSR corresponding to the greatest power coefficients of all studied rotors, and averagely by 126% in the range 0.4<TSR<0.8. Unfortunately, the rotor with circular end-plate faces with the greatest levels of the drag and lift forces exerting on the rotor shaft. Introducing some designing indices shows that a rotor with quarter-spherical end-plate can be a good alternative for one with circular end-plate.
- Open Access
IoT-Based Sensor Data Fusion for Determining Optimality Degrees of Microclimate Parameters in Commercial Greenhouse Production of Tomato
Optimum microclimate parameters, including air temperature (T), relative humidity (RH) and vapor pressure deficit (VPD) that are uniformly distributed inside greenhouse crop production systems are essential to prevent yield loss and fruit quality. The objective of this research was to determine the spatial and temporal variations in the microclimate data of a commercial greenhouse with tomato plants located in the mid-west of Iran. For this purpose, wireless sensor data fusion was incorporated with a membership function model called Optimality Degree (OptDeg) for real-time monitoring and dynamic assessment of T, RH and VPD in different light conditions and growth stages of tomato. This approach allows growers to have a simultaneous projection of raw data into a normalized index between 0 and 1. Custom-built hardware and software based on the concept of the Internet-of-Things, including Low-Power Wide-Area Network (LoRaWAN) transmitter nodes, a multi-channel LoRaWAN gateway and a web-based data monitoring dashboard were used for data collection, data processing and monitoring. The experimental approach consisted of the collection of meteorological data from the external environment by means of a weather station and via a grid of 20 wireless sensor nodes distributed in two horizontal planes at two different heights inside the greenhouse. Offline data processing for sensors calibration and model validation was carried in multiple MATLAB Simulink blocks. Preliminary results revealed a significant deviation of the microclimate parameters from optimal growth conditions for tomato cultivation due to the inaccurate timer-based heating and cooling control systems used in the greenhouse. The mean OptDeg of T, RH and VPD were 0.67, 0.94, 0.94 in January, 0.45, 0.36, 0.42 in June and 0.44, 0.0, 0.12 in July, respectively. An in-depth analysis of data revealed that averaged OptDeg values, as well as their spatial variations in the horizontal profile were closer to the plants’ comfort zone in the cold season as compared with those in the warm season. This was attributed to the use of heating systems in the cold season and the lack of automated cooling devices in the warm season. This study confirmed the applicability of using IoT sensors for real-time model-based assessment of greenhouse microclimate on a commercial scale. The presented IoT sensor node and the Simulink model provide growers with a better insight into interpreting crop growth environment. The outcome of this research contributes to the improvement of closed-field cultivation of tomato by providing an integrated decision-making framework that explores microclimate variation at different growth stages in the production season.
Open AccessIoT-Based Sensor Data Fusion for Determining Optimality Degrees of Microclimate Parameters in Commercial Greenhouse Production of Tomato
Optimum microclimate parameters, including air temperature (T), relative humidity (RH) and vapor pressure deficit (VPD) that are uniformly distributed inside greenhouse crop production systems are essential to prevent yield loss and fruit quality. The objective of this research was to determine the spatial and temporal variations in the microclimate data of a commercial greenhouse with tomato plants located in the mid-west of Iran. For this purpose, wireless sensor data fusion was incorporated with a membership function model called Optimality Degree (OptDeg) for real-time monitoring and dynamic assessment of T, RH and VPD in different light conditions and growth stages of tomato. This approach allows growers to have a simultaneous projection of raw data into a normalized index between 0 and 1. Custom-built hardware and software based on the concept of the Internet-of-Things, including Low-Power Wide-Area Network (LoRaWAN) transmitter nodes, a multi-channel LoRaWAN gateway and a web-based data monitoring dashboard were used for data collection, data processing and monitoring. The experimental approach consisted of the collection of meteorological data from the external environment by means of a weather station and via a grid of 20 wireless sensor nodes distributed in two horizontal planes at two different heights inside the greenhouse. Offline data processing for sensors calibration and model validation was carried in multiple MATLAB Simulink blocks. Preliminary results revealed a significant deviation of the microclimate parameters from optimal growth conditions for tomato cultivation due to the inaccurate timer-based heating and cooling control systems used in the greenhouse. The mean OptDeg of T, RH and VPD were 0.67, 0.94, 0.94 in January, 0.45, 0.36, 0.42 in June and 0.44, 0.0, 0.12 in July, respectively. An in-depth analysis of data revealed that averaged OptDeg values, as well as their spatial variations in the horizontal profile were closer to the plants’ comfort zone in the cold season as compared with those in the warm season. This was attributed to the use of heating systems in the cold season and the lack of automated cooling devices in the warm season. This study confirmed the applicability of using IoT sensors for real-time model-based assessment of greenhouse microclimate on a commercial scale. The presented IoT sensor node and the Simulink model provide growers with a better insight into interpreting crop growth environment. The outcome of this research contributes to the improvement of closed-field cultivation of tomato by providing an integrated decision-making framework that explores microclimate variation at different growth stages in the production season.
- Open Access
- 1 May 2019
- Vol. 4 (4) , 5
Improving Thermo-hydraulic Performance of the Parallel-plate Flow with a Particular Counter-current Flow Division
- 1 May 2019
- Vol. 4 (4) , 5
Open AccessImproving Thermo-hydraulic Performance of the Parallel-plate Flow with a Particular Counter-current Flow Division
- Open Access
- 1 June 2017
- Vol. 1 (1) , 39-48
Comparative Analysis on Thermal Performance of Different Natural-draft Dry Cooling Towers under Crosswind Condition
- 1 June 2017
- Vol. 1 (1) , 39-48
Open AccessComparative Analysis on Thermal Performance of Different Natural-draft Dry Cooling Towers under Crosswind Condition