Kevin Cronin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kevin Cronin has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- José Caro-Corrales
Posgrado en Ciencia y Tecnología de Alimentos, Facultad de Ciencias Químico Biológicas Universidad Autónoma de Sinaloa Culiacán Sinaloa Mexico
3 shared publications - Song Miao
Fujian Agriculture and Forestry University
2 shared publications Xin Gao
2 shared publicationsAli Doǧan Demir
Department of Process Engineering, University College, Cork
1 shared publication- António Barbot
ESE, Polytechnic of Porto
1 shared publication Denis Ring
1 shared publication
Latest Publications
- Open Access
The Evolution of Variance and Entropy of the Granule Size Distribution in Fluidized Bed Agglomeration
The evolution of the variance and entropy of granule size in the fluidized bed agglomeration process using two different aggregation kernels is examined. The first is a constant kernel (aggregation is independent of both time and granule size) and permits the most unconstrained agglomeration process that can occur where granules in any size class (up to a maximum size) can be formed at any point in time. This gives the fastest and largest increase in the variance and entropy of the resulting granule size distribution. The second kernel is a mechanistic kernel including a granule growth-limiting mechanism, in this case implemented by the consideration that not all collisions result in coalescence. This markedly changes the evolution of the variance and entropy of the distribution and reduces both significantly. Quantifying the entropy of the distribution provides another perspective on the change in the size distribution in an agglomeration process. It is shown that entropy can provide a better measure of size evolution than variance in that it represents the changing shape of the distribution more closely.
Open AccessThe Evolution of Variance and Entropy of the Granule Size Distribution in Fluidized Bed Agglomeration
The evolution of the variance and entropy of granule size in the fluidized bed agglomeration process using two different aggregation kernels is examined. The first is a constant kernel (aggregation is independent of both time and granule size) and permits the most unconstrained agglomeration process that can occur where granules in any size class (up to a maximum size) can be formed at any point in time. This gives the fastest and largest increase in the variance and entropy of the resulting granule size distribution. The second kernel is a mechanistic kernel including a granule growth-limiting mechanism, in this case implemented by the consideration that not all collisions result in coalescence. This markedly changes the evolution of the variance and entropy of the distribution and reduces both significantly. Quantifying the entropy of the distribution provides another perspective on the change in the size distribution in an agglomeration process. It is shown that entropy can provide a better measure of size evolution than variance in that it represents the changing shape of the distribution more closely.
- Open Access
An Experimental Study on the Dilute Phase Pneumatic Conveying of Fat-Filled Milk Powders: Particle Breakage
Powder breakage during pneumatic conveying negatively affects the properties of dairy products and causes increased dusting, reduced wettability, and decreased product performance. In particular, particle breakage is a serious issue for fat-filled milk powder (FFMP) which, if it breaks, releases fat that causes odours and leads to sticky blocked pipes. In this work, a conveying rig (dilute phase, positive pressure) with 50 mm diameter food grade stainless steel pipes (1.5 m high and 5 m conveying distance with three 90° bends, two in the vertical plane and one in the horizontal plane) was built as the test system. The effects of operating conditions (conveying air velocity and solid loading rate) on the attrition of FFMP in a dilute phase conveying system were experimentally studied. Four quality characteristics were measured before and after conveying: bulk density, particle size distribution, wettability, and solubility, to access the influence of particle breakage. Conveying air speed shows a significant impact on powder breakage. As air speed increased, more breakage occurred, and the volume mean diameter D[4,3] decreased by around 50%, using the largest conveying air speed of 38 m/s. Bulk density increased accordingly whereas wettability decreased with an increase in air speed, resulting from the higher breakage rate. On other hand, improving the solid loading rate can further reduce the breakage level, but the positive effect is not as good as decreasing air speed.
Open AccessAn Experimental Study on the Dilute Phase Pneumatic Conveying of Fat-Filled Milk Powders: Particle Breakage
Powder breakage during pneumatic conveying negatively affects the properties of dairy products and causes increased dusting, reduced wettability, and decreased product performance. In particular, particle breakage is a serious issue for fat-filled milk powder (FFMP) which, if it breaks, releases fat that causes odours and leads to sticky blocked pipes. In this work, a conveying rig (dilute phase, positive pressure) with 50 mm diameter food grade stainless steel pipes (1.5 m high and 5 m conveying distance with three 90° bends, two in the vertical plane and one in the horizontal plane) was built as the test system. The effects of operating conditions (conveying air velocity and solid loading rate) on the attrition of FFMP in a dilute phase conveying system were experimentally studied. Four quality characteristics were measured before and after conveying: bulk density, particle size distribution, wettability, and solubility, to access the influence of particle breakage. Conveying air speed shows a significant impact on powder breakage. As air speed increased, more breakage occurred, and the volume mean diameter D[4,3] decreased by around 50%, using the largest conveying air speed of 38 m/s. Bulk density increased accordingly whereas wettability decreased with an increase in air speed, resulting from the higher breakage rate. On other hand, improving the solid loading rate can further reduce the breakage level, but the positive effect is not as good as decreasing air speed.
- Open Access
- 5 June 2020
- Published by MDPI AG in Chemengineering
- Vol. 4 (2) , 35
Self-Agglomeration in Fluidised Beds after Spray Drying
Many powders are produced in spray-drying processes from liquid concentrates. Self-agglomeration can be performed in a fluidised bed where the spray-dried powder is agglomerated using the liquid concentrate as the binder material. This has advantages over traditional wet agglomeration in fluid beds using liquid binders (such as water or sugar solutions). These include thermal energy savings and no additional non-aqueous binder components added. The work presented has two parts. The first part is experimental, which investigated the self-agglomeration of whey protein isolate (WPI) powder as a case-study. It showed that satisfactory agglomeration was achieved with a great improvement in the wettability of the powder. The second part of the work performed thermal energy analysis to estimate the energy saving potential of self-agglomeration, and how this is influenced by binder to powder ratio and binder solids concentration. For the WPI case-study, the analysis showed there is potential for a 19% saving in thermal energy requirement for self-agglomeration in comparison to traditional agglomeration using a water binder.
- 5 June 2020
- Published by MDPI AG in Chemengineering
- Vol. 4 (2) , 35
Open AccessSelf-Agglomeration in Fluidised Beds after Spray Drying
Many powders are produced in spray-drying processes from liquid concentrates. Self-agglomeration can be performed in a fluidised bed where the spray-dried powder is agglomerated using the liquid concentrate as the binder material. This has advantages over traditional wet agglomeration in fluid beds using liquid binders (such as water or sugar solutions). These include thermal energy savings and no additional non-aqueous binder components added. The work presented has two parts. The first part is experimental, which investigated the self-agglomeration of whey protein isolate (WPI) powder as a case-study. It showed that satisfactory agglomeration was achieved with a great improvement in the wettability of the powder. The second part of the work performed thermal energy analysis to estimate the energy saving potential of self-agglomeration, and how this is influenced by binder to powder ratio and binder solids concentration. For the WPI case-study, the analysis showed there is potential for a 19% saving in thermal energy requirement for self-agglomeration in comparison to traditional agglomeration using a water binder.
- 27 October 2014
- Published by Wiley in International Journal of Dairy Technology
- Vol. 67 (4) , 604-605
Food Plant Engineering Systems (2013), 2nd edn. edited by D.Ring, K.Cronin. ISBN: 978‐1‐4398‐1 4809‐8.
- 27 October 2014
- Published by Wiley in International Journal of Dairy Technology
- Vol. 67 (4) , 604-605
Food Plant Engineering Systems (2013), 2nd edn. edited by D.Ring, K.Cronin. ISBN: 978‐1‐4398‐1 4809‐8.
- 23 May 2013
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 68, 49-66
Variability in output torque of capstan and wrap spring elements
- 23 May 2013
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 68, 49-66
Variability in output torque of capstan and wrap spring elements
- 4 May 2011
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 225 (3) , 195-204
Prediction of the collapse time of an outdoor storage tank under rainfall due to internal steam condensation
Thin-walled storage tanks are prone to vacuum collapse due to the development of a net external pressure. Condensation of steam inside the vessel can cause a rapid development of this mode of failure. External atmospheric conditions also affect the process; specifically, the enhanced heat transfer associated with rainfall on the vessel external surface accelerates the collapse process. Short but intense rain storms are becoming more common. An expression to predict the time taken for a storage vessel to collapse while subject to external rainfall is developed. Good agreement was found between the predictions of the modelling techniques and the experimentally obtained results. It is shown that the thermal energy stored in the vessel wall is very significant in determining the collapse time especially for outdoor vessels exposed to rain.
- 4 May 2011
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 225 (3) , 195-204
Prediction of the collapse time of an outdoor storage tank under rainfall due to internal steam condensation
Thin-walled storage tanks are prone to vacuum collapse due to the development of a net external pressure. Condensation of steam inside the vessel can cause a rapid development of this mode of failure. External atmospheric conditions also affect the process; specifically, the enhanced heat transfer associated with rainfall on the vessel external surface accelerates the collapse process. Short but intense rain storms are becoming more common. An expression to predict the time taken for a storage vessel to collapse while subject to external rainfall is developed. Good agreement was found between the predictions of the modelling techniques and the experimentally obtained results. It is shown that the thermal energy stored in the vessel wall is very significant in determining the collapse time especially for outdoor vessels exposed to rain.
- 31 July 2010
- Published by Elsevier in Journal of Food Engineering
- Vol. 99 (2) , 175-183
Heat transfer analysis of cheese cooling incorporating uncertainty in temperature measurement locations: Model development and validation
- 31 July 2010
- Published by Elsevier in Journal of Food Engineering
- Vol. 99 (2) , 175-183
Heat transfer analysis of cheese cooling incorporating uncertainty in temperature measurement locations: Model development and validation
- 31 July 2010
- Published by Elsevier in Journal of Food Engineering
- Vol. 99 (2) , 159-165
Heat transfer analysis of cheese cooling incorporating uncertainty in temperature measurement locations: Application to the industrial process
- 31 July 2010
- Published by Elsevier in Journal of Food Engineering
- Vol. 99 (2) , 159-165
Heat transfer analysis of cheese cooling incorporating uncertainty in temperature measurement locations: Application to the industrial process
- 1 June 2008
- Published by SAGE Publications in Food Science and Technology International
- Vol. 14 (3) , 241-250
Impingement Cooking of Meat Products: Effect of Variability on Final Temperature
Heat transfer coefficient (HTC) for chicken fillets and beef burgers were determined at a number of product-to-tube distances in an impingement air unit. The coefficient varied from < 100 W/m2 K to over 200 W/m2 K depending on the input parameter settings. The level of variation in the coefficient between adjacent product items in the oven has been quantified as ±20 W/m 2 K. Models of sheat transfer for both food products have been developed. Parameter of the models indicated that depending on the product, either dimensional variation in the product or dispersion in the HTC between products can make the dominant contribution to dispersion in final product temperature.
- 1 June 2008
- Published by SAGE Publications in Food Science and Technology International
- Vol. 14 (3) , 241-250
Impingement Cooking of Meat Products: Effect of Variability on Final Temperature
Heat transfer coefficient (HTC) for chicken fillets and beef burgers were determined at a number of product-to-tube distances in an impingement air unit. The coefficient varied from < 100 W/m2 K to over 200 W/m2 K depending on the input parameter settings. The level of variation in the coefficient between adjacent product items in the oven has been quantified as ±20 W/m 2 K. Models of sheat transfer for both food products have been developed. Parameter of the models indicated that depending on the product, either dimensional variation in the product or dispersion in the HTC between products can make the dominant contribution to dispersion in final product temperature.
- 31 January 2007
- Published by Elsevier in Journal of Loss Prevention in the Process Industries
- Vol. 20 (1) , 7-14
Prevention of thermo-hydraulic rupture of solvent transfer pipes in the pharmaceutical industry
- 31 January 2007
- Published by Elsevier in Journal of Loss Prevention in the Process Industries
- Vol. 20 (1) , 7-14
Prevention of thermo-hydraulic rupture of solvent transfer pipes in the pharmaceutical industry